Torsion Bar

A torsion bar suspension, also known as a torsion spring suspension, is any vehicle suspension that uses a torsion bar as its main weight-bearing spring. One end of a long metal bar is attached firmly to the vehicle chassis; the opposite end terminates in a lever, the torsion key, mounted perpendicular to the bar, that is attached to a suspension arm, a spindle, or the axle. Vertical motion of the wheel causes the bar to twist around its axis and is resisted by the bar's torsion resistance. The effective spring rate of the bar is determined by its length, cross section, shape, material, and manufacturing process.

Usage

Torsion bar suspensions are used on combat vehicles and tanks like the T-72, Leopard 1, Leopard 2, M26 Pershing, M18 Hellcat, M48 Patton, M60 Patton and the M1 Abrams (many tanks from World War II used this suspension), and on modern trucks and SUVs from Ford, Chrysler, GM, Mitsubishi, Mazda, Nissan, Isuzu, LuAZ, and Toyota. Class 8 truck manufacturer Kenworth also offered a torsion bar suspension for its K100C and W900A models, up to about 1981.

Manufacturers change the torsion bar or key to adjust the ride height, usually to compensate for engine weight.

Advantages and disadvantages

The main advantages of a torsion bar suspension are soft ride due to elasticity of the bar, durability, easy adjustability of ride height, and small profile along the width of the vehicle. It takes up less of the vehicle's interior volume than coil springs.

Torsion bars reached the height of their popularity on mass-production road cars in the middle of the 20th century at the same time that unitary construction was being adopted. At a time when the mechanics of stress and metal fatigue in monocoque body frames was poorly understood, torsion bars were very attractive to vehicle designers as the bars could be mounted to reinforced parts of the central structure, typically the bulkhead. Using MacPherson struts to achieve independent front suspension with coil springs meant providing strong turrets in the frontal structure of the car.

A disadvantage is that torsion bars, unlike coil springs, usually cannot provide a progressive spring rate. In most torsion bar systems, ride height (and therefore many handling features) may be changed by simply adjusting bolts that connect the torsion bars to the steering knuckles. In most cars with this type of suspension, swapping torsion bars for a different spring rate is usually an easy task. Longitudinal torsion bars extend under the passenger compartment, cutting into interior space by raising the floor, while in transverse systems, torsion bar length is limited by vehicle width.

Leveling

Some vehicles use torsion bars to provide automatic levelling, using a motor to pre-stress the bars to provide greater resistance to load and, in some cases (depending on the speed with which the motors can act), to respond to changes in road conditions. Height adjustable suspension has been used to implement a wheel-change mode where the vehicle is raised on three wheels so that the remaining wheel is lifted off the ground without the aid of a jack. This example is of a vehicle that uses oleopneumatic suspension where a high pressure pump primes a pressure reservoir that feeds terminating spheres with hydraulic oil (LHM) to achieve suspension. The ride height is maintained by cross-linking front and rear suspension spheres using hydraulic connecting pipes.

History

The first vehicle to use torsion bars was Leyland Eight designed by J. G. Parry-Thomas and produced from 1920 to 1923, however its rear suspension, patented in 1919, was retrospectively named "torsion bar assisted" by Leyland in a 1966 publication because the bars only complemented the leaf springs. Less than two dozen cars (including racing variants) were produced, and the suspension was only ever used again on Marlborough-Thomas racing cars few years later.

In 1923 Parry-Thomas patented an updated design featuring a true torsion bar design with no leaf springs, however the inventor's death in a car crash in 1927 prevented its further development. Therefore the invention is often credited to the Porsche GmbH, which patented it in 1931 and later used in a lot of designs.

The front wheel drive Citroën Traction Avant from 1934 was the first to implement the idea in a serially produced car, featuring independent front torsion bar suspension and a flexible trailing dead axle, also sprung by torsion bars. The flexibility of the axle beam provided wheel location features like a twist beam axle. Also in the 1930s, Porsche's prototypes of the first Volkswagen Beetle incorporated torsion bars—especially their transverse mounting style. Czechoslovakian Tatra's 1948 T600 Tatraplan employed rear torsion bar suspension, the only Tatra to do so.

The system first saw military use in the Swedish Stridsvagn L-60 tank of 1934. Its suspension was developed by German engineers, including Porsche employee Karl Rabe who also held patents on torsion bar suspensions personally.

It was used extensively in European cars like Renault, Citroën and Volkswagen, as well as by Packard in the 1950s. The Packard used torsion bars at both front and rear, and interconnected the front and rear systems to improve ride quality. Morris Minor and Oxford from the late 1940s onwards used a front torsion bar system very similar to the Citroën, as did the Riley RM models. The revolutionary Jaguar E-Type introduced in 1961 had a torsion bar front suspension very similar to the Citroën and Morris Minor, and an independent coil spring rear suspension using four shock absorbers with concentric springs.

An early application of a torsion bar in an American car was by Hudson Motor Car Company of Detroit who had introduced the innovative front axle flex suspension in 1934 Hudson and Hudson Terraplane, Terraplane cars and realized for 1935 that a transverse torsion bar linked to the rear axle was needed as an anti-roll bar to stabilize the cars. The single torsion bar was mounted through the frame sides behind the rear axle and then attached by arms and links to the front side of the spring U-bolt plates. Axle flex was discontinued for the 1936 model year.

Post-war the use of torsion bar front suspension was a defining feature of British Morris Motors, Morris cars, starting with the Morris Minor of 1948, its larger Morris Oxford MO counterpart and the upmarket Morris Six MS, plus the Wolseley Motors, Wolseley-badged upmarket variants of the latter two models. The designer of these cars, Alec Issigonis, was inspired by the Citroën Traction Avant, Traction Avant's suspension, although the Morris cars were rear-wheel drive and used conventional leaf springs for their rear axles. The Minor used Lever arm shock absorber, lever arm dampers with its torsion bars while the Oxford and the Six used innovative Shock absorber, telescopic dampers. The Minor remained in production largely unchanged until 1972 and was replaced by the Morris Marina which also used the torsion bar-lever arm damper system for its front suspension—one of the last new cars worldwide to be introduced with the system and which remained in production until 1984. The Oxford/Six platform was developed through several Morris Oxford series II, revised series which used Issigonis' torsion bar system until 1959 when the new Morris Oxford Farina, Farina Oxford was introduced using front suspension with coil springs, lower wishbones and lever arm dampers.

The most famous American passenger car application was the Chrysler system used beginning with all Chrysler products starting with the 1957 model year in cars such as the Imperial (automobile)#Second generation (1957–1966), Imperial Crown series, Chrysler Windsor, DeSoto Firedome#1957–61, DeSoto Firedome, Dodge Coronet#Fourth generation (1957–1959), Dodge Coronet and Plymouth Belvedere#1957–1959, Plymouth Belevedere although Chrysler's "Torsion-Air" suspension was only for the front axle; the same basic system (longitudinal mounting) was maintained until the 1981 introduction of the Chrysler K platform, K-car. A reengineered torsion bar suspension, introduced with the 1976 Dodge Aspen, introduced transverse-mounted torsion bars (possibly based on the Volkswagen Type 3 passenger car) until production ended in 1989 (with Chrysler's M platform). Some generations of the Dodge Dakota and Dodge Durango#First generation (DN; 1997), Durango used torsion bars on the front suspension.

General Motors first used torsion bars on their light-duty pickup trucks in 1960 until it was phased out in 1963 where traditional coil springs are used up front for their 2WD trucks. Its first use in a passenger car was in 1966, starting with the E-platform vehicles (Oldsmobile Toronado, Cadillac Eldorado), 4WD Chevrolet S-10, S-10 pickups and Chevrolet Astro, Astro vans with optional AWD, and since 1988, full size trucks and SUVs with 4WD (GMT400, GMT800, and GMT900 series).

Porsche used four-wheel torsion bar suspension for their Porsche 356, 356 and Porsche 911, 911 series from 1948 until 1989 with the introduction of the 964. They are also used in the front suspension of the Porsche 914, 914 as well as the rear suspension of the Porsche 924, 924, Porsche 944, 944, and Porsche 968, 968. Honda also used front torsion bars on the Honda_Civic_(third_generation), third generation Civic and other variants built on the same platform including the Honda Ballade, Ballade and Honda CRX, first generation CRX.

Variations

The German World War II Panther tank (and some Tigers) had double torsion bars. Needing bars longer than the width of the tank to get the required spring rate and maximum elastic bend angle from available steel alloys, designer Ernst Lehr created a suspension that effectively folded the bars in half. For each wheel, one rod was attached to the suspension arm, while another was mounted to a nearby point on the frame. On the opposite side of the tank, the two rods were attached to each other and fitted into a pivot. Deflection of the suspension arm caused both halves of the double torsion bar to twist. A disadvantage of the torsion bar suspension used in Tiger and Panther tanks (and many other WWII-era tanks and other Armoured fighting vehicle, AFVs) was the inability to incorporate an escape hatch through the bottom of the hull, a common feature of WWII-era tanks, as the torsion bar arrangement would have blocked crew access to such a hatch; however, the absence of leaf, coil or volute springs often left a large expanse of the side of the hull clear to include a side-escape hatch, and it was rare for a tank to be flipped over in such a way that all top-side hatches were unable to open, which is the purpose of ventral hatches.

Many contemporary main battle tanks use torsion bar suspension, including the American M1 Abrams, German Leopard 2, and Chinese MBT-3000, though the newest generation of tanks such as the Russian T-14 Armata utilize an adjustable hydraulic suspension. Due to their small size, tremendous load capacity, and relative ease of service, torsion bar suspension has been ideal for tanks, though it is not without disadvantage. The large travel and high elasticity of the torsion bars results in a "rocking" motion when the tank is moving or coming to a sudden stop. A gun stabilizer must be used to compensate for the rocking motion. Due to the massive weight of a main battle tank, compared to an automobile, there is a much greater risk of breaking a torsion bar on sudden bumps or maneuvers, and if it is not replaced in short order the reduced suspension can affect the maneuverability of the vehicle, and in extreme cases risk immobilizing the vehicle as the reduced capacity of the suspension causes additional torsion bars to break.

Some front-wheel drive automobiles use a related type of torsion beam suspension, usually called a twist-beam rear suspension, in which the rear wheels are carried on trailing arms connected by a laterally mounted torsion beam, as found on the Mitsubishi Debonair#Second generation, Mitsubishi Debonair. The actual springing medium for these is usually coil springs. The torsion beam functions both as wheel locating arm and as an anti-roll bar to resist lateral motion of the wheels as the body leans in turns. Its advantages are that it is inexpensive to manufacture and install, and engages a minimum amount of interior volume, leaving more space for the carriage of passengers, cargo, and other components. Because the torsion beam acts in the lateral plane, not vertically, the twist beam axle cannot provide ride height adjustment, and it suffers, to some extent, similar car handling limitations as other beam axle suspensions. However these limitations may not be apparent on the road, because of the trend towards firmer, more sporty suspension setups with more limited wheel travel. Twist-beam rear suspensions were pioneered on the Volkswagen Golf in the early 1970s, and remain common on compact cars and minivans.

Other uses

Torsion bars were sometimes used instead of conventional coil valve springs in some older motorcycles, such as the Honda CB450, and also on the Panhard Dyna X and Panhard Dyna Z cars of the 1950s. They were also used in the door mechanism of the DMC DeLorean automobile.

References

Bibliography

*
*
*

{{DEFAULTSORT:Torsion Bar Suspension
Automotive suspension technologies
Armoured fighting vehicle equipment
Tank suspensions
French inventions