The Rocket (locomotive)

Stephenson's ''Rocket'' is an early steam locomotive of 0-2-2 wheel arrangement. It was built for and won the Rainhill Trials of the Liverpool and Manchester Railway (L&MR), held in October 1829 to show that improved locomotives would be more efficient than stationary steam engines.

''Rocket'' was designed and built by Robert Stephenson in 1829, and built at the Forth Street Works of his company in Newcastle upon Tyne.

Though ''Rocket'' was by no means the first steam locomotive, it was the first to bring together several innovations to produce the most advanced locomotive of its day. It is the most famous example of an evolving design of locomotives by Stephenson that became the template for most steam engines in the following 150 years.

The locomotive was preserved and displayed in the Science Museum in London until 2018, after which it was displayed at the National Railway Museum in York.

Design

Overall layout

The locomotive had a tall smokestack chimney at the front, a cylindrical boiler in the middle, and a separate firebox at the rear.
The large front pair of wooden wheels was driven by two external cylinders set at an angle. The smaller rear wheels were not coupled to the driving wheels, giving an 0-2-2 wheel arrangement.

Design objectives

Stephenson designed ''Rocket'' for the Rainhill trials, and the specific rules of that contest. As the first railway intended for passengers more than freight, the rules emphasised speed and would require reliability, but the weight of the locomotive was also tightly restricted. Six-wheeled locomotives were limited to six tons, four-wheeled locomotives to four and a half tons. In particular, the weight of the train expected to be hauled was to be no more than three times the actual weight of the locomotive. Stephenson realised that whatever the size of previously successful locomotives, this new contest would favour a fast, light locomotive of only moderate hauling power.

Innovations

Single pair of driving wheels

Stephenson's most visible decision was to use a single pair of driving wheels, with a small carrying axle behind. This was the first 0-2-2 and first single driver locomotive. The use of single drivers gave several advantages. The weight of coupling rods was avoided and the second axle could be smaller and lightweight, as it only carried a small portion of the weight. ''Rocket'' placed just over  tons of its  ton total weight onto its driving wheels, a higher axle load than ''Sans Pareil'', even though the 0-4-0 was heavier overall at 5 ton, and officially disqualified by being over the  ton limit. Early locomotive designers had been concerned that the adhesion of a locomotive's driving wheels would be inadequate, but Stephenson's past experience convinced him that this would not be a problem, particularly with the light trains of the trials contest.

Multiple boiler fire-tubes

''Rocket'' uses a multi-tubular boiler design. Previous locomotive boilers consisted of a single pipe surrounded by water (though the '' Lancashire Witch'' did have twin flues). ''Rocket'' had 25 copper fire-tubes that carry the hot exhaust gas from the firebox, through the wet boiler to the blast pipe and chimney. This arrangement resulted in a greatly increased surface contact area of hot pipe with boiler water when compared to a single large flue. Additionally, radiant heating from the enlarged separate firebox helped deliver a further increase in steaming and hence boiler efficiency.

The original innovator of multiple fire-tubes is unclear, between Stephenson and Marc Seguin. It is known that Seguin visited Stephenson to observe ''Locomotion'' and that he also built two multi-tubular locomotives of his own design for the Saint-Étienne–Lyon railway before ''Rocket''. ''Rocket''s boiler was of the more highly developed form, with the separate firebox and a blastpipe for draught, rather than Seguin's cumbersome fans, but ''Rocket'' was not the first multi-tubular boiler, although it remains unclear just whose invention it was.

The benefits of increasing the fire-tube area had also been attempted with Ericsson and Braithwaite's ''Novelty'' at Rainhill. Their design though used a single fire-tube, folded in three. This offered an increased surface area, but only at the cost of a proportionately increased length and so poor draught on the fire. Its arrangement also made tube cleaning impractical.

The advantages of the multiple-tube boiler were quickly recognised, even for heavy, slow freight locomotives. By 1830, Stephenson's past employee Timothy Hackworth had re-designed his return-flued ''Royal George'' as the return-tubed ''Wilberforce'' class.

Blastpipe

''Rocket'' also used a blastpipe, feeding the exhaust steam from the cylinders into the base of the chimney so as to induce a partial vacuum and pull air through the fire. Credit for the invention of the blastpipe is disputed, though Stephenson used it as early as 1814. The blastpipe worked well on the multi-tube boiler of ''Rocket'' but on earlier designs with a single flue through the boiler it had created so much suction that it tended to rip the top off the fire and throw burning cinders out of the chimney, vastly increasing the fuel consumption.

Cylinders closer to the horizontal

Like the ''Lancashire Witch'', ''Rocket'' had two cylinders set at angle from the horizontal, with the pistons driving a pair of diameter wheels. Most previous designs had the cylinders positioned vertically, which gave the engines an uneven swaying motion as they progressed along the track. Subsequently, ''Rocket'' was modified so that the cylinders were set close to horizontal, a layout that influenced nearly all designs that followed.

Pistons directly connected to driving wheels

Again like the ''Lancashire Witch'', the pistons were connected directly to the driving wheels, an arrangement which is found in subsequent steam locomotives.

Separate firebox

The firebox was separate from the boiler and was double walled, with a water jacket between them. Stephenson recognised that the hottest part of the boiler, and thus the most effective for evaporating water, was that surrounding the fire itself. This firebox was heated by radiant heat from the glowing coke, not just convection from the hot exhaust gas.

Locomotives of ''Rocket''s era were fired by coke rather than coal. Local landowners were already familiar with the dark clouds of smoke from coal-fired stationary engines and had imposed regulations on most new railways that locomotives would 'consume their own smoke'. The smoke from a burning coke fire was much cleaner than that from coal. It was not until 30 years later and the development of the long firebox and brick arch that locomotives would be effectively able to burn coal directly.

''Rocket''s first firebox was of copper sheet and of a somewhat triangular shape from the side. The throatplate was of firebrick, possibly the backhead too. When rebuilt around 1831, this was replaced by a wrought iron backhead and throatplate, with a drum wrapper (now missing), presumed to be of copper, between them. This gave a larger internal volume and encouraged better combustion within the firebox, rather than inside the tubes. These early fireboxes formed a separate water space from the boiler drum and were connected by prominent external copper pipes.

Credit for the design

There have been differences in opinion on who should be given the credit for designing ''Rocket''. George Stephenson had designed several locomotives before but none as advanced as ''Rocket''. At the time that ''Rocket'' was being designed and built at the Forth Banks Works, he was living in Liverpool overseeing the building of the Liverpool and Manchester Railway. His son Robert had recently returned from a stint working in South America and resumed as managing director of Robert Stephenson and Company. He was in daily charge of designing and constructing the new locomotive. Although he was in frequent contact with his father in Liverpool and probably received advice from him, it is difficult not to give the majority of the credit for the design to Robert. A third person who may deserve a significant amount of credit is Henry Booth, the treasurer of the Liverpool and Manchester Railway. He is believed to have suggested to Robert Stephenson that a multi-tube boiler should be used.

Evolution of the Stephenson locomotive design

Before ''Rocket''

''Rocket'' was built at a time of rapid development of steam engine technology. It was based on experience gained from earlier designs by George and Robert Stephenson, including the Killingworth locomotive ''Blücher'' (1814); ''Locomotion'' (1825); and the '' Lancashire Witch'' (1828).

''Rocket'' type locomotives

''Rocket'' was followed by a number of other engines of similar 0-2-2 layout with rear-mounted cylinders built for the L&MR before it opened on 15 September 1830, culminating in the ''Northumbrian'' (1830), by which time the cylinders were horizontal. Other engines of the ''Rocket'' design which were delivered to the Liverpool and Manchester railway included ''Arrow'', ''Comet'', ''Dart'' and ''Meteor'', all being delivered to the railway during 1830.

After ''Rocket''

At around the same time, Stephenson experimented with front-mounted cylinders. The unsuccessful 0-4-0 ''Invicta'', built in 1829 immediately after ''Rocket'', still had them at an angle. The successful 2-2-0 locomotive ''Planet'' (1830) had internal front-mounted cylinders set to the horizontal.

Engines built to the ''Planet'' design and the subsequent 2-2-2 ''Patentee'' design of 1833 made the design of ''Rocket'' obsolete.

Rainhill Trials

On 20 April 1829, the board of the Liverpool and Manchester Railway project passed a resolution for a competition to be held to prove their railway could be reliably operated by steam locomotives, there being advice from eminent engineers of the age that stationary engines would be required. A prize of £500 was offered as an incentive to the winner, with strict conditions a locomotive would need to meet to enter the trial. Robert Stephenson was able to report to Henry Booth on 5 September 1829 that ''Rocket'' had performed initial manufacturer tests with flying colours at Killingworth. ''Rocket'' was dismantled at Newcastle and began the long trip to Rainhill: by horse wagon to Carlisle; lighter to Port Carlisle then by the ''Cumberland'' steamer to Liverpool for re-assembly on 18 September 1829. ''Rocket'' passed the trial requirement of achieving an average speed of over by over 40 percent. Demonstrations also saw ''Rocket'' consistently and easily haul a carriage of over 20 person up the Whiston incline at over , and light engine running of around . No other locomotive at the trials was able to achieve anything like the level of performance reliably, with partners Booth and Stephensons sharing the £500 winnings, and perhaps more importantly the need for stationary engines being demonstrated as unnecessary with sceptics such as Rastrick on the way to conversion.

Operation and subsequent history

Opening-day accident

The opening ceremony of the L&MR on 15 September 1830 was a considerable event, drawing luminaries from the government and industry, including the Prime Minister, the Duke of Wellington. The day started with a procession of eight trains setting out from Liverpool for Manchester. The parade was led by ''Northumbrian'' driven by George Stephenson, and included ''Phoenix'' driven by his son Robert, ''North Star'' driven by his brother Robert Sr. and ''Rocket'' driven by assistant engineer Joseph Locke. The day was marred by the death of William Huskisson, the Member of Parliament for Liverpool, who was struck and killed by ''Rocket'' at Parkside.

Service

History between 1830 and 1840 is only vaguely documented.
From 1830 to 1834, ''Rocket'' served on the Liverpool and Manchester Railway.

After service on the L&MR, ''Rocket'' was used between 1836 and 1840 on Lord Carlisle's Railway near Brampton, in Cumberland (now Cumbria), England.

Modifications

Built as a prototype to win a speed trial, the engine was soon superseded by improved designs, such as Stephenson's ''Northumbrian'' and ''Planet'' designs, both of 1830.

Within a few years, the ''Rocket'' itself had been much modified to be similar to the ''Northumbrian'' class. The cylinders were altered to a near-horizontal position, compared to the angled arrangement as new; the firebox capacity was enlarged and the shape simplified; and the locomotive was given a drum smokebox. These arrangements can be seen in the engine today.
Such are the changes in the engine from 1829 that ''The Engineer'' magazine, circa 1884, concluded that "it seems to us indisputable that the ''Rocket'' of 1829 and 1830 were totally different engines".

Lord Dundonald's rotary engine

In 1834, the engine was selected for further (unsuccessful) modifications to test a newly developed rotary steam engine designed by Admiral The 10th Earl of Dundonald. At a cost of nearly £80, ''Rocket''s cylinders and driving rods were removed and two of the engines were installed directly on its driving axle with a feedwater pump in between. On 22 October, of that year, an operational trial was held with disappointing results; one witness observing, that "the engine could not be made to draw a train of empty carriages". Due to inherent design flaws and engineering difficulties associated with their design, Lord Dundonald's engines were simply too feeble for the task.

Lord Carlisle's Railway

In 1836, ''Rocket'' was sold for £300 and began service on the Brampton Railway, a mineral railway in Cumberland that had recently converted to Stephenson gauge. It remained here at Tindale, after service, until 1862 and its donation to the Patent Office Museum, London.

Preservation

In 1862, ''Rocket'' was donated to the Patent Office Museum in London (now the Science Museum) by the Thompsons of Milton Hall, near Brampton.

The locomotive still exists, though it has not been operated since becoming a museum exhibit. It was displayed at the Science Museum for 150 years, although in a form much modified from its state at the Rainhill Trials. In 2018, it was displayed first in Newcastle and then in Manchester at the Science and Industry Museum from 25 September 2018 to 8 September 2019. From 2019, it has been displayed at the National Railway Museum, York.

Replicas

In 1923, Buster Keaton had a functioning replica built for the film '' Our Hospitality''. Two years later, the replica was used again in the Al St. John film, '' The Iron Mule'', directed by Keaton's mentor, Roscoe "Fatty" Arbuckle. The subsequent whereabouts of the replica are unknown. There are, however, at least two other replicas of ''Rocket'' in the US, both built by Robert Stephenson and Hawthorns in 1929; one is at the Henry Ford Museum in the Metro Detroit suburb of Dearborn, Michigan, the other at the Museum of Science and Industry, Chicago.

The earliest full-size replica of ''Rocket'' seems to have been one depicted on a London and North Western Railway postcard (therefore pre-1923).

A cut-away static replica (see photo above) was built in 1935 and displayed for many years next to the original at London's Science Museum.

In 1979, a further, working replica ''Rocket'' was built by Locomotion Enterprises in the Springwell workshops at the Bowes Railway for the 150th anniversary celebrations. It first worked in public on a short length of track in front of the Albert Memorial in Kensington Gardens from 25 August to 2 September 1979, before going to Newcastle on 9 September, York on 16 October and running the measured mile, between Lea Green and Rainhill, on the last two days at the Rocket 150 celebrations from 24 to 26 May 1980. It has a shorter chimney than the original to clear the bridge at Rainhill: successive additions of ballast and heavier rail have raised the track, leaving less headroom than in the 19th century. As of 2022, both of these replicas were based at the National Railway Museum, York, with the original ''Rocket''.

Models

In 1963, Tri-ang Railways released a 00 Gauge model of ''Rocket'' containing three coaches and crew members. It was produced until 1969 by Tri-ang Hornby.
It was re-introduced to the Hornby range in 1982 until 1983 in Hornby Railways packaging. However this 1982 re-introduced model was un-catalogued, and it was only available through exclusive retailers and from Hornby directly.

In 1980, as part of the Rocket 150 anniversary, Hornby launched a gauge live steam ''Rocket'' locomotive, with additional track and coaches available separately.

In 2020, Hornby announced a newly tooled 00 Gauge model of Stephenson's ''Rocket'' with three coaches and crew members as part of their Centenary range. It was available as a standard model and a limited edition with commemorative certificate of authentication in retro 1963 Hornby Centenary Tri-ang Railways packaging.

See also

* ''Novelty''
* ''Invicta''
* ''Lion''
* ''Tom Thumb'' (first American-built steam locomotive)
* ''John Bull''
* ''Locomotion''
* Rainhill Trials
*''Sans Pareil''
* ''Stourbridge Lion'' (first American-operated steam locomotive)

Notes

Footnotes

References

*
*
*
*

External links

The Science Museum – Stephenson's ''Rocket'' locomotive, 1829

''The Engineer''
magazine examines the differences between the 1829 and 1830 ''Rocket'', as reprinted in ''Scientific American'' Supplement, No. 460, 25 October 1884.
*

{{Authority control

Railway locomotives introduced in 1829
Rocket
Early steam locomotives
English inventions
History of Northumberland
Rocket
Land speed record rail vehicles
Liverpool and Manchester Railway locomotives
Preserved steam locomotives of Great Britain
Rainhill Trials locomotives
Standard gauge steam locomotives of Great Britain
Steam engines in the Science Museum, London