Transmitarray Antenna
   HOME

TheInfoList



OR:

A transmitarray antenna (or just transmitarray or called as layered lens antenna) is a phase-shifting surface (PSS), a structure capable of focusing electromagnetic radiation from a source antenna to produce a high-Antenna gain, gain Directional antenna, beam. Transmitarrays consist of an array of unit cells placed above a source (feeding) Antenna (radio), antenna. Phase shifts are applied to the unit cells, between elements on the receive and transmit surfaces, to focus the incident wavefronts from the feeding antenna. These thin surfaces can be used instead of a Luneburg lens, dielectric lens. Unlike phased arrays, transmitarrays do not require a feed network, so losses can be greatly reduced. Similarly, they have an advantage over Reflectarray antenna, reflectarrays in that feed blockage is avoided. It is worth clarifying that transmitarrays can be used in both transmit and receive modes: the waves are transmitted through the structure in either direction. An important parameter in transmitarray design is the F/D ratio, which determines the Antenna aperture, aperture efficiency. F is the focal length and D is the diameter of the transmitarray. The projected area of the feeding antenna determines the illumination efficiency of a transmitarray panel. Provided that the insertion loss of each unit cell is minimised, an aperture area appropriate to the feed radiation pattern can efficiently focus the wavefronts from the feed.


Overview of techniques

Transmitarrays can be split into two types: fixed and reconfigurable. As described earlier, a transmitarray is a Phase (waves)#Phase shift, phase-shifting surface consisting of an array of unit cells. These focus the wavefronts from a feeding antenna into a narrower beamwidth. By applying a progressive phase shift across the aperture of the transmitarray, the beam can be focused and steered towards a direction away from boresight (0° angles).


Fixed transmitarrays

First, consider fixed transmitarrays. At each location on the surface of the structure, the unit cells are physically scaled or rotated in order to obtain the required amplitude and Phase (waves), phase distribution. Thus, only one focusing direction is available. The aim is to approximate the ideal phase distribution, such as \Delta \phi(x,y) = \frac\sqrt for a feed located at (0,0,-F), which can be achieved by discretising the surface of the transmitarray into several Zone plate, Fresnel zones. High aperture efficiency (55%) can be achieved at oblique Angle of incidence (optics), angles of incidence using precision-machined double split ring Slot antenna, slot unit cells. A switched-beam transmitarray covering the 57 – 66 GHz band has been reported. Three different types of unit cells were used, based on Microstrip antenna, patches and coupling slots. Similarly, a 60 GHz design used unit cells with a 2-bit phase resolution and selected an optimal F/D ratio to widen the Bandwidth (signal processing), bandwidth. When F/D = 0.5, a scan loss of 2.2 dB was achieved at a 30° steering angle. Different types of unit cells have been used within the same transmitarray. In, Slot antenna, slot elements were placed near the centre of the transmitarray, as their Polarization (waves), polarisation performance is better at Angle of incidence (optics), normal incidence, whereas double square ring Slot antenna, slot elements were used at the edges, as they perform better at oblique Angle of incidence (optics), incidence angles. This enabled the subtended (flare) angle of the feed Horn antenna, horn to be increased, and hence the length of the horn, and the overall antenna size, to be reduced. Unit cells were not required at the centre of the transmitarray, where the phase shift was 0°. This reduced the insertion loss to around 1 dB at 105 GHz, as the majority of the beam amplitude was in the central region. In a different design, Post-wall waveguide, substrate integrated waveguide (SIW) aperture coupling was employed to reduce insertion losses and widen the Bandwidth (signal processing), bandwidth of a transmitarray operating at 140 GHz. Due to the large number of Via (electronics), vias required, this performance improvement was at the expense of a more complex and costly fabrication. It has been shown that transmitarray implementation can be divided into two approaches: layered-scatterer and guided-wave. The first approach uses multiple coupled layers to achieve a phase shift, but has poor Side lobe, sidelobe level (SLL) performance when steering due to higher-order Floquet theory, Floquet modes. The second approach enables wider steering, at the expense of increased hardware cost and complexity.


Reconfiguration methods

In a reconfigurable transmitarray, the focusing direction is determined by electronically controlling the phase shift through each unit cell. This enables the beam to be steered towards the Mobile telephony, user. Electronic reconfiguration can be achieved by several possible methods. PIN diodes can be used to enable fast phase reconfiguration with an insertion loss below 1 dB. However, a large number of components is typically required, which increases the cost. A reconfigurable transmitarray, operating at 29 GHz with Circular polarization, circular polarisation, has been demonstrated as a Beamforming, beamformer. A Antenna boresight, boresight Antenna gain, gain of 20.8 dBi was achieved, and the scan loss was 2.5 Decibel, dB at 40°. Another implementation example is an active Zone plate, Fresnel Reflectarray antenna, reflectarray with control circuitry for the PIN diodes. Although the unit cells were optimised, the scan loss was 3.4 dB at 30°. Reconfigurable Electromagnetic radiation#Near and far fields, near-field focusing can be implemented using slots containing PIN diodes. By adjusting the phase compared to a reference wave, Holography, holographic principles enabled the use of a compact, planar feeding structure and suppression of Side lobe, undesired lobes. This was extended in to an implementation of a Mills Cross Array, Mills cross based on PIN diodes, in which an aperture was synthesised for Imaging radar, imaging applications. Stub (electronics)#Radial stub, Radial stubs were used to isolate the bias lines from the Radio frequency, RF. By switching combinations of meta-elements on or off, the scan loss was 0 dB for steering angles of ±30°, but the Antenna efficiency, total efficiency was only 35%. In 2019, a transmitarray was fed by a planar phased array operating at 10 GHz, in order to achieve a high beam crossover gain level whilst maintaining an Antenna aperture, aperture efficiency of 57.5%. The scan loss was 3.13 dB at ±30°. Similarly, a lens-enhanced phased array antenna, similar to a transmitarray, has been demonstrated. By combining the beam steering capabilities of phased arrays and the focusing properties of transmitarrays, this hybrid antenna has a smaller form factor, and steers to ±45° in both planes with a 3.2 dB increase in directivity at this angle. Its reconfigurable phase-shifting surface (PSS) contained Microelectromechanical systems, micro-electro-mechanical (MEMS) switches to change the length of resonators, sandwiched within an antenna-filter-antenna structure. The PSS created the optimal 2D phase distribution needed to achieve high-gain beam focusing, but the MEMS fabrication process was complex and costly, requiring a large number of control lines. MEMS and other mechanical switching methods can achieve a relatively low insertion loss (2.5 dB) and an excellent Intermodulation, linearity, but are prone to stiction and reliability issues Metamaterial, Reconfigurable materials have shown promise for enabling a low-loss beam steering transmitarray. A Vanadium(IV) oxide, vanadium dioxide reconfigurable metasurface operating at 100 GHz was presented in using a crossed-slot unit cell. A heating element was used to Heat transfer, thermally control the phase shift through each cell. The permittivity of liquid crystal (and hence the phase shift) can be reconfigured by applying a voltage between two parallel conducting plates. However, liquid crystal has several practical challenges. The liquid must be hermetically sealed in a cavity, and the crystal orientations aligned with the cavity walls in an unbiased state. The liquid can flow between cells, causing a variation in the Radio frequency, RF properties of the transmitarray, and dynamic instabilities. Liquid crystal Reflectarray antenna, reflectarrays have been extensively investigated at 78 GHz and 100 GHz. In, a fishnet metamaterial lens was designed, using liquid crystal to achieve a 360° electronically controlled phase range. The 5 dB unit cell insertion loss could be reduced by controlling the Bloch impedance (both \epsilon_ and \mu_) of each unit cell. The advantage of liquid crystal is that its loss tangent reduces with frequency, however it suffers from a slow switching time of around 100 ms and fabrication difficulties.


Geometry and radiation pattern

A conventional transmitarray consists of a planar arrangement of unit cells, illuminated by a feed source. For this structure, the required Phase (waves), phase distribution is: \phi_(x_, y_, z_) = -k_(\sin\cosx_ + \sin\siny_ + \cosz_) where (\theta_, \phi_) are the Spherical coordinate system, elevation and azimuth steering directions, and (x_, y_, z_) are the coordinates of unit cell m. Note that x_ = \left(m + \frac\right)d, y_ = \left(n + \frac\right)d, and z_ = 0. M and N are the total numbers of unit cells in the x- and y-directions respectively. When steering in azimuth only, this simplifies to: \phi_(x_, y_) = k_(d_ - \sin(x_\cos + y_\sin)) where d_ = \sqrt and (x_,y_,z_) are the coordinates of the feed, in this case (0,0,-F). The overall radiation pattern can be calculated, using. Here, terms are combined to express the formula in full: E(\theta, \phi) = \sum_^ \sum_^ \cos^\left(\right) \frac, T_, e^\times e^ where the radiation pattern of the steered array source is modelled as \cos^\left(\right). The term e^ corresponds to the phases applied to the transmitarray unit cells, to undo the phase variation due to the geometry of the cells from the feed, i.e. e^e^ = 1.


Edge taper and aperture efficiency

G_ = 10\log_\left(\cos^\right) An edge taper of around -10 dB is desired, so that the illumination efficiency is maximised. For a planar (conventional) transmitarray, fed by an antenna with radiation pattern G_(\theta,\phi) = \cos^, and subtended angle \theta_ = \tan^\left(\right), the taper efficiency is calculated by: \eta_ = 1 - \cos^ \eta_ = \frac \frac \theta_ is a function of F/D. Note that \cos(\tan^) = \frac, so using x = \frac, this formula can be expressed in terms of F/D, rather than the subtended angle. The illumination efficiency is the product of these: \eta_ = \eta_\eta_. The overall aperture efficiency \eta_ is obtained by multiplying by material losses and any directivity reduction terms.


Unit cell design

A variety of unit cell shapes have been proposed, including double square Loop antenna, loops, U-shaped resonators, Microstrip antenna, microstrip patches, and Slot antenna, slots. The double square loop has the best transmission performance at wide Angle of incidence (optics), angles of incidence, whereas a large Bandwidth (signal processing), bandwidth can be achieved if Jerusalem cross slots are used. A switchable FSS using MEMS capacitors was demonstrated in. The four-legged loaded element was used to obtain full control of the Bandwidth (signal processing), bandwidth and Angle of incidence (optics), incidence angle properties. For space applications, in which thermal expansion must be considered, air gaps between layers can be used instead of dielectric, to minimise the insertion loss (metal-only transmitarray). However, this increases the thickness, and requires a large number of screws for mechanical support.


Design example

Consider the structure of the proposed 1-bit unit cell, which operates at 28 GHz. It is based on the design presented in. It consists of two metal layers, printed on a Rogers RT5880 substrate material having a thickness of 0.254 mm, a dielectric constant of 2.2, and a loss tangent of 0.0009. Each metal layer consists of a pair of crossed slots, and the incident fields are Vertical polarization, vertically polarised (E_). By selecting a symmetrical unit cell shape, they can be adapted for dual Linear polarization, linear or Circular polarization, circular polarisation. The two metal layers are separated by a 3 mm thick layer of ePTFE material (of Permittivity, dielectric constant \epsilon_ = 1.4), which creates a 100° phase shift between these layers. The unit cell has reduced thickness and insertion loss compared with multilayer designs. The unit cell can be reconfigured between two phase states, OFF (0°) and ON (180°). For the OFF state, it has a Jerusalem cross slot structure. In the ON state, the slots are not loaded with Jerusalem cross (JC) shaped caps, producing a large phase change. Due to the use of single-pole resonators (a two-layer structure), the transmission performance was challenging to achieve, requiring fine-tuning of the unit cell physical dimensions. Both unit cell states were simulated in CST Microwave Studio using Floquet theory, Floquet ports and the frequency domain solver. This included the magnitude and phase of the E_ transmission coefficient through the unit cell in ON and OFF states. A phase change of 189° was observed, which is close to 180°, and the transmission magnitude is at least -1.76 dB at 28 GHz for both states. For the JC cells, the Current density, surface currents are in opposite directions (anti-phase) on each conductor layers, whereas for the CS cells, the Current density, surface currents are in the same direction (in-phase). The Phase (waves), phase difference between states is given by: \Delta\phi = \angle_ -\angle_.


Biasing reconfigurable unit cells

PIN diodes can be placed across the ends of the Jerusalem cross caps, applying a different bias voltage for each state. Coupling capacitor, DC blocking in the form of interdigital capacitors would be needed to isolate the bias voltages, and Radio frequency, RF Choke (electronics), choke inductors would be needed at the ends of the bias lines. To demonstrate the transmitarray concept, unit cells with fixed phase shifts were used in the fabricated prototypes. For electronic reconfiguration, PIN diodes would need to be placed on both the top and bottom layers. When the diodes are forward biased (ON), incident radiation is transmitted through the slots with a 180° phase change, but when the diodes are reverse biased (OFF), the current path is lengthened so that there is minimal phase change (around 0°). The MACOM MA4GP907 diode has an ON resistance R_ = 4.2 \Omega, an OFF resistance R_ = 300 k\Omega, and small parasitic inductance and capacitance values (L_ = 0.05 nH, C_ = 42 fF in the 28 GHz band). Given that it has a high OFF Electrical resistance, resistance value, and that the switching time is very fast (2 ns), this component is suitable for the design. The position and orientation of the bias lines must be chosen to minimise their effect on the transmission of the incident waves through the structure. If the lines are sufficiently narrow (width up to 0.1 mm), they will present a high Electrical impedance, impedance, so will have less effect on the wavefronts. As they act as a polarising grid, the bias lines should be perpendicular to the incident field direction. This design has no ground plane, so each group of active unit cells must have both a V_ and a ground connection. As groups of cells share the same bias voltages, these lines can be routed between adjacent cells. The required number of external control lines is equal to the number of beam directions supported, so is inversely proportional to the steering resolution. The bias lines could be implemented as large blocks of copper around the unit cells, separated by thin gaps (through which the RF wave propagation is heavily attenuated). The gaps may need to be meandered to form Coupling capacitor, DC block capacitors. Stub (electronics)#Radial stub, Radial stubs or high-impedance lines of length \frac (a quarter of a guided wavelength) could be used as Choke (electronics), chokes (inductors) on the external control lines, to prevent the Radio frequency, RF signal from affecting the Direct current, DC control circuitry.


Discussion

A key challenge in transmitarray design is that the insertion loss increases with the number of Electrical conductor, conductor layers within the unit cell. In, it was shown that the optimal number of layers to maximise the Antenna gain, gain (directivity vs. Insertion loss, loss) is 3 layers. This has been corroborated by an analysis of cascaded sheet admittances. However, for scenarios when cost and efficiency are more important, a low-cost two-layer transmitarray may be preferred. Alternatively, the efficiency can be improved by integrating the antenna used to feed the transmitarray within a monolithic chip, as recently demonstrated in the D band (waveguide), D-band frequency range (114 – 144 GHz). Another high-gain transmitarray was demonstrated, operating at D band (waveguide), D-band (110 – 170 GHz). The F/D was optimised to maximise the aperture efficiency. The antenna was connected to an integrated frequency multiplier to demonstrate a communication link. A data rate of 1 Gbit/s was achieved over a distance of 2.5 m, with an error vector magnitude (EVM) of 25%


See also

*Phased array *Metamaterial *Luneburg lens, Dielectric Lens *Extremely high frequency, Millimeter Wave *Beamforming *Reflectarray antenna, Reflectarray Antenna


References


External links


Welcome
''5GCHAMPION project - a transmitarray demonstrator'' {{Antenna Types Antennas (radio) Radio frequency antenna types