HOME

TheInfoList



OR:

Texas Mill was a cotton spinning mill in the Whitelands district of Ashton-under-Lyne,
Greater Manchester Greater Manchester is a metropolitan county and combined authority, combined authority area in North West England, with a population of 2.8 million; comprising ten metropolitan boroughs: City of Manchester, Manchester, City of Salford, Salford ...
, in England. It was built between 1905 and 1907 for the Ashton Syndicate by Sydney Stott of Oldham. It was destroyed in a massive fire on 22–23 October 1971. It had been re-equipped as a ring mill for spinning artificial fibres when it was destroyed.


Location

Texas mill was built next to Minerva Mill in Whitelands, in a meander of the River Tame.


History

The Minerva Spinning Company Limited was registered in 1891 to build the Minerva Mill at Whitelands. The directors were Messrs Barlow, Marland, Coop, Newton, Pollitt and Pownall; they were later referred to as the Ashton syndicate. The syndicate then built Rock Mill, Atlas Mill, Curzon Mill, Tudor Mill, Cedar Mill and finally the Texas Mill. The syndicate registered the Texas Mill Co. Ltd, with a capital of GBP70,000 to build this, their seventh mill. The cotton industry peaked in 1912 when it produced 8 billion yards of cloth. The great war of 1914–1918 halted the supply of raw cotton, and the British government encouraged its colonies to build mills to spin and weave cotton. The war over, Lancashire never regained its markets. On 7 January 1921 all the syndicate's mills went into voluntary liquidation and were passed to the Atlas Mills Ltd. group . They were struggling. The Bank of England set up the
Lancashire Cotton Corporation The Lancashire Cotton Corporation was a company set up by the Bank of England in 1929, to rescue the Lancashire spinning industry by means of horizontal rationalisation. In merged 105 companies, ending up in 1950 with 53 operating mills. It was ...
in 1929 to attempt to rationalise and save the industry. Atlas Mills Limited was taken over by the LCC in 1929. Thus, Texas Mill was one of 104 mills brought into LCC ownership, and one of the 53 mills that survived through to 1950. It had been converted to rings and it produced 20 to 40 count high class combed and carded hosiery yarns. Later it converted to artificial fibres. Still spinning, was destroyed by fire 22–23 October 1971. The Texas Mill fire was one of the largest fires in the North West. Lancashire County Fire Service initially responded, but soon requested assistance from neighbouring brigades such was the size of the incident. Firefighters fought the blaze using about 40 pumps plus specials and relief appliances. Sadly, whilst engaged in firefighting duties, Manchester Fire Brigade Fireman Norman Nolan of Blackley Fire Station died when a wall collapsed on him whilst he was working on an escape. Alongside him was Sub Officer Bill Partington of Mossley Fire Station, who survived although badly injured. The site was cleared and became a bus depot, and when that closed it became a factory.


Architecture

This was a 30 bay mill designed by Sydney Stott, it had his trademark double rings on its chimney. It was four storeys high built on a basement from engineering brick. It had a Hotel-de-Ville style water tower. The large windows were in groups of three, and there was yellow brick decoration. The six bay engine house, boiler house and chimney were to the north.


Power

The 1907 steam engine was by
George Saxon & Co George Saxon & Co was an English engineering company that manufactured stationary steam engines. It was based in the Openshaw district of Greater Manchester, Manchester. The company produced large steam-driven engines for power stations and la ...
, of Openshaw. It was built as a triple expansion at 1200 hp. It was altered in 1921 and became a 1500 hp vertical three cylinder compound engine. The later engine had a 28" diameter high pressure (HP) in the centre, with a 33" IP and 51"LP cylinder. It had a 4 ft stroke and ran at 78rpm. The boiler operated at 170psi. The 22 ft flywheel was mounted at end of shaft, driving 28 ropes. There were Corliss valves on all cylinders. Air pumps were driven from LP and IP crossheads. In 1921 a new 51"LP cylinder was built, the old 21"HP removed and the IP was used for HP.


Equipment

The mule frames were provided by Hetherington and Sons Ltd. There were 76,896 mule spindles spinning medium counts of yarn from American cotton. By 1948, the mill had been re-equipped with 35,000 ring spindles.


Usage

Texas Mill was used for spinning medium counts of American cotton. In 1951 it was spinning high-class combed and carded hosiery yarns from 20's to 40's count. In 1971 it was spinning artificial fibres.


Owners

* The Ashton syndicate * Atlas Mills * Lancashire Cotton Corporation * Courtauld's Northern Textiles


See also

*
Textile manufacturing Textile Manufacturing or Textile Engineering is a major industry. It is largely based on the conversion of fibre into yarn, then yarn into fabric. These are then dyed or printed, fabricated into cloth which is then converted into useful goods ...
*
Stott The Stotts were a family of architects from Oldham, North West England, of Scottish descent who specialised in the design of cotton mills. James Stott was the father, Joseph and his elder brother Abraham Stott had rival practices, and in later ...


References


Bibliography

* * * * *


External links


www.cottontown.org

www.spinningtheweb.org.uk
{{DEFAULTSORT:Texas Mill, Ashton-Under-Lyne Textile mills in Tameside Buildings and structures in Ashton-under-Lyne Textile mills owned by the Lancashire Cotton Corporation Demolished buildings and structures in Greater Manchester Industrial buildings completed in 1907 1907 establishments in England 1971 disestablishments in England Buildings and structures demolished in 1971