HOME

TheInfoList



OR:

A swivel is a connection that allows the connected object, such as a
gun A gun is a ranged weapon designed to use a shooting tube (gun barrel) to launch projectiles. The projectiles are typically solid, but can also be pressurized liquid (e.g. in water guns/cannons, spray guns for painting or pressure washing, p ...
,
chair A chair is a type of seat, typically designed for one person and consisting of one or more legs, a flat or slightly angled seat and a back-rest. They may be made of wood, metal, or synthetic materials, and may be padded or upholstered in vario ...
,
swivel caster A swivel is a connection that allows the connected object, such as a gun, chair, swivel caster, or an anchor rode to rotate horizontally or vertically. Swivel designs A common design for a swivel is a cylindrical rod that can turn freely wi ...
, or an
anchor An anchor is a device, normally made of metal , used to secure a vessel to the bed of a body of water to prevent the craft from drifting due to wind or current. The word derives from Latin ''ancora'', which itself comes from the Greek ἄγ ...
rode to rotate horizontally or vertically.


Swivel designs

A common design for a swivel is a cylindrical rod that can turn freely within a support structure. The rod is usually prevented from slipping out by a nut, washer or thickening of the rod. The device can be attached to the ends of the rod or the center. Another common design is a sphere that is able to rotate within a support structure. The device is attached to the sphere. A third design is a hollow cylindrical rod that has a rod that is slightly smaller than its inside diameter inside of it. They are prevented from coming apart by flanges. The device may be attached to either end. A swivel joint for a
pipe Pipe(s), PIPE(S) or piping may refer to: Objects * Pipe (fluid conveyance), a hollow cylinder following certain dimension rules ** Piping, the use of pipes in industry * Smoking pipe ** Tobacco pipe * Half-pipe and quarter pipe, semi-circula ...
is often a threaded connection in between which at least one of the pipes is curved, often at an angle of 45 or 90 degrees. The connection is tightened enough to be water- or air-tight and then tightened further so that it is in the correct position.


Anchor rode swivel

Swivels are also used in the nautical sector as an element of the anchor rode and in a boat mooring systems. With yachts, the swivel is most commonly used between the anchor and chain. There is a school of thought that anchor swivels should not be connected to the anchor itself, but should be somewhere in the chain rode. The anchor swivel is expected to fulfill two purposes: * If the boat swings in a circle the chain may become twisted and the swivel may alleviate this problem. * If the anchor comes up turned around, some swivels may right it.


Concerns

The biggest concern about anchor swivels is that they might introduce a weak link to the rode. * With most swivels the shaft is nice and tidily embedded in the other half of the swivel as in the example of the
stainless steel Stainless steel is an alloy of iron that is resistant to rusting and corrosion. It contains at least 11% chromium and may contain elements such as carbon, other nonmetals and metals to obtain other desired properties. Stainless steel's corros ...
anchor swivel shown here. When used in marine applications, and worse in tropical climates, this is a cause for corrosion, even in stainless steel. ** The chromium in stainless steel creates a passivation layer on the surface that protects the steel from rusting. In low oxygen situations and/or warm water this passivation layer breaks down and corrosion will set in. Low oxygen will occur in crevasses which stary wet (cracks, welds, shackle threads, keel bolts, etc.) or confined spaces (swivel shafts, etc.). Corrosion may also happen internally. Welding may cause the cromium to bind with carbon and thus indirectly lead to corrosion. * In come cases the shaft is threaded with a nut welded onto it to hold the two bits together. First of all, a threaded bar is inherently weaker than a solid bar of the same diameter. Then there is the issue of the welds not holding. * When a boat swings on a well-embedded anchor, this can cause strong lateral loads on the swivel, causing its jaws to be prized open - thus disconnecting the chain from the swivel. Hence the above advice from Rocna. * Some boating schools teach that the anchor should be pulled tight against the bow roller by the windlass. This causes stress to the weakest link (swivel) as the vessel pounds though waves and can thus speed up failure.


See also

*
Slewing bearing {{unreferenced, date=January 2016 To "slew" means to turn without change of place. A slewing bearing or slew ngring (also called a turntable bearing) is a rotational rolling-element bearing that typically supports a heavy but slow-turning or sl ...


References


Bibliography

* Blackwell, Alex & Daria; ''Happy Hooking – the Art of Anchoring,'' 2008, 2011, 2019 White Seahorse; * Hinz, Earl R.; ''The Complete Book of Anchoring and Mooring, Rev. 2d ed.,'' 1986, 1994, 2001 Cornell Maritime Press;


External links

* {{wiktionary-inline, swivel Joining Mechanical engineering