A slip joint is a mechanical construction allowing extension and compression in a linear structure.

General forms

Slip joints can be designed to allow continuous relative motion of two components or it can allow an adjustment, by unclamping from one fixed position, and re-clamping to another. Examples of the latter are

tripod A tripod is a portable three-legged frame or stand, used as a platform for supporting the weight and maintaining the stability of some other object. The three-legged (triangular stance) design provides good stability against gravitational loads ...

hiking pole Trekking poles (also known as hiking poles, hiking sticks or walking poles) are a common hiking accessory that function to assist walkers with their rhythm, to provide stability, and reduce strain on joints on rough terrain. Description When in ...

s, or similar telescoping device. The clamping mechanism is based on a

cam Calmodulin (CaM) (an abbreviation for calcium-modulated protein) is a multifunctional intermediate calcium-binding messenger protein expressed in all eukaryotic cells. It is an intracellular target of the secondary messenger Ca2+, and the bind ...

, a

set screw In American English, a set screw is a screw that is used to secure an object, by pressure and/or friction, within or against another object, such as fixing a pulley or gear to a shaft. A set screw is normally used without a nut (which distingu ...

, or a similar locking mechanism. Slip joints can also be non-telescoping, such as the joints on some older wooden surveyor's

levelling rod Levelling or leveling (American English; see spelling differences) is a branch of surveying, the object of which is to establish or verify or measure the height of specified points relative to a datum. It is widely used in geodesy and cartog ...

s. These use a joint that keeps the sections offset from each other but able to be slid together for transport. Examples of continuous slip joints are given below.

Special purpose slip joints

Civil engineering

Slip joints in large structures are used to allow the independent motion of large components while enabling them to be joined in some way. For example, if two tall buildings are to be joined with a pedestrian

skyway A skyway, skybridge, skywalk, or sky walkway is an elevated type of pedway connecting two or more buildings in an urban area, or connecting elevated points within mountainous recreational zones. Urban skyways very often take the form of enclos ...

at some high level, there are two options in structural engineering. If the buildings are identical in mass and elasticity they will tend to respond similarly to

ground motion Ground motion is the movement of the earth's surface from earthquakes or explosions. Ground motion is produced by seismic waves that are generated by sudden slip on a fault or sudden pressure at the explosive source and travel through the earth a ...

induced by

earthquake An earthquake (also known as a quake, tremor or temblor) is the shaking of the surface of the Earth resulting from a sudden release of energy in the Earth's lithosphere that creates seismic waves. Earthquakes can range in intensity, from ...

s. In this case, it may be appropriate to construct a rigid connection between the buildings, although this may require additional supporting members within the structures. On the other hand, a lower cost connection may be made by using a lightweight structure that is not coupled rigidly but instead is allowed to slide or "float" relative to one or both structures. This is especially suitable where the two structures may respond differently to ground motion. The structure will not be completely free to move but rather may use elastic materials to locate it near the center of its range of motion and

viscous The viscosity of a fluid is a measure of its resistance to deformation at a given rate. For liquids, it corresponds to the informal concept of "thickness": for example, syrup has a higher viscosity than water. Viscosity quantifies the inter ...

shock absorber A shock absorber or damper is a mechanical or hydraulic device designed to absorb and damp shock impulses. It does this by converting the kinetic energy of the shock into another form of energy (typically heat) which is then dissipated. Most sh ...

s to absorb energy and to restrict the speed of relative motion. When a sliding connection is used it is extremely important that there be sufficient range of motion without failure to accommodate the maximum credible relative motion of the structures. Additional "fail-safe" flexible connections may be added to ensure that the structure does not fall, although it may be damaged to a point of being unserviceable or unrepairable. Slip joints are common under conditions where temperature changes can cause expansion and contraction that may overstress a structure. These are generally referred to as ''

expansion joint An expansion joint, or movement joint, is an assembly designed to hold parts together while safely absorbing temperature-induced expansion and contraction of building materials, and vibration, or to allow movement due to ground settlement or seis ...

s.'' Bridges and overpasses frequently have sliding joints that allow a deck to move relative to piers or abutments. The joints can be constructed with elastomeric pads that permit motion or can use rollers on flat surfaces to allow the ends to move smoothly. The exact details are limited by the imagination of the designer.

Mechanical engineering

Slip joints are sometimes found in tubular structures such as piping but are generally avoided for this application due to requirements for sealing against leakage, instead of using either a large loop that is allowed to flex or a semi-rigid bellow. Slip joints are used when the main problem is a large axial movement.Slip Type Expansion Joints
U.S. Bellows, (retrieved January 2012) Pipe supports often are slip joints to allow for the thermal expansion or contraction of the pipe relative to the support.

Wastewater plumbing

Slip joint connections are also commonly used in wastewater plumbing, most commonly under kitchen sinks. Here, the slip joint provides a water-tight seal for non-pressurized drainage, with adjustability to aid installation. The slip joint includes a gasket that fits snugly on a pipe end, with a threaded nut behind the gasket, but with gasket position adjustable as needed. This pipe end fits loosely into another with a flange for the gasket to seal against, and threads for the nut to clamp the gasket to the flange.

References