Revolver (other)

A revolver (also called a wheel gun) is a repeating handgun that has at least one barrel and uses a revolving cylinder containing multiple chambers (each holding a single cartridge) for firing. Because most revolver models hold up to six cartridges before needing to be reloaded, revolvers are also commonly called six shooters.

Before firing, cocking the revolver's hammer partially rotates the cylinder, indexing one of the cylinder chambers into alignment with the barrel, allowing the bullet to be fired through the bore. The hammer cocking in nearly all revolvers are manually driven, and can be achieved either by the user using the thumb to directly pull back the hammer (as in single-action), via internal linkage relaying the force of the trigger-pull (as in double-action), or both (as in double/single-action). By sequentially rotating through each chamber, the revolver allows the user to fire multiple times until having to reload the gun, unlike older single-shot firearms that had to be reloaded after each shot. Some rare revolver models can utilize the blowback of the preceding shot to automatically cock the hammer and index the next chamber, although these self-loading revolvers (known as automatic revolvers, despite technically being semi-automatic) never gained any widespread usage.

Although largely surpassed in convenience and ammunition capacity by semi-automatic pistols, revolvers still remain popular as back-up and off-duty handguns among American law enforcement officers and security guards and are still common in the American private sector as defensive, sporting, and hunting firearms. Famous revolvers models include the Colt 1851 Navy Revolver, the Webley, the Colt Single Action Army, the Colt Official Police, Smith & Wesson Model 10, the Smith & Wesson Model 29 of '' Dirty Harry'' fame, the Nagant M1895, and the Colt Python.

Though the majority of weapons using a revolver mechanism are handguns, other firearms may also have a revolver action. These include some models of rifles, shotguns, grenade launchers, and cannons. Revolver weapons differ from Gatling-style rotary weapons in that in a revolver only the chambers rotate, while in a rotary weapon there are multiple full firearm actions with their own barrels which rotate around a common ammunition feed.

History

In the development of firearms, an important limiting factor was the time required to reload the weapon after it was fired. While the user was reloading, the weapon was useless, allowing an adversary to attack the user. Several approaches to the problem of increasing the rate of fire were developed, the earliest involving multi-barrelled weapons which allowed two or more shots without reloading. Later weapons featured multiple barrels revolving along a single axis.

A matchlock revolver with a single barrel and four chambers held at the Tower of London is believed to have been invented some time in the 15th century. A revolving three-barrelled matchlock pistol in Venice is dated from at least 1548. During the late 16th century in China, Zhao Shi-zhen invented the Xun Lei Chong, a five-barreled musket revolver spear. Around the same time, the earliest examples of what today is called a revolver were made in Germany. These weapons featured a single barrel with a revolving cylinder holding the powder and ball. They would soon be made by many European gun-makers, in numerous designs and configurations. However, these weapons were complicated, difficult to use and prohibitively expensive to make, and as such they were not widely distributed.

In the early 19th century, multiple-barrel handguns called "pepper-boxes" were popular. Originally they were muzzleloaders, but in 1837, the Belgian gunsmith Mariette invented a hammerless pepperbox with a ring trigger and turn-off barrels that could be unscrewed.

In 1836, American Samuel Colt patented a popular revolver which led to the widespread use of the revolver. According to Colt, he came up with the idea for the revolver while at sea, inspired by the capstan, which had a ratchet and pawl mechanism on it, a version of which was used in his guns to rotate the cylinder by cocking the hammer. This provided a reliable and repeatable way to index each round and did away with the need to manually rotate the cylinder. Revolvers proliferated largely due to Colt's ability as a salesman, but his influence spread in other ways as well. The build quality of his company's guns became famous, and its armories in America and England trained several seminal generations of toolmakers and other machinists, who had great influence in other manufacturing efforts of the next half century.

Early revolvers were caplocks and muzzleloaders: the user poured black powder into each chamber, rammed down a bullet on top of it, then placed a percussion cap on the nipple at the rear of each chamber, where the hammer would fall on it. This was similar to loading a traditional single-shot muzzle-loading pistol, except that the powder and shot could be loaded directly into the front of the cylinder rather than having to be loaded down the whole length of the barrel. Importantly, this allowed the barrel itself to be rifled, since the user was not required to force the tight-fitting bullet down the barrel in order to load it (a traditional muzzle-loading pistol had a smoothbore and relatively loose-fitting shot, which allowed easy loading, but gave much less accuracy). When firing the next shot, the user would raise his pistol vertically as he cocked the hammer back so as to let the fragments of the burst percussion cap fall out so as to not jam the mechanism. Some of the most popular cap-and-ball revolvers were the Colt Model 1851 "Navy" model, 1860 "Army" model, and Colt Pocket Percussion Revolvers, all of which saw extensive use in the American Civil War. Although American revolvers were the most common, European arms makers were making numerous revolvers by that time as well, many of which found their way into the hands of the American forces. These included the single-action Lefaucheux and LeMat revolvers and the Beaumont–Adams and Tranter revolvers—early double-action weapons in spite of being muzzle-loaders.

In 1854, Eugene Lefaucheux introduced the Lefaucheux Model 1854, the first revolver to use self-contained metallic cartridges rather than loose powder, pistol ball, and percussion caps. It is a single-action, pinfire revolver holding six rounds.

On November 17, 1856, Daniel B. Wesson and Horace Smith signed an agreement for the exclusive use of the Rollin White Patent at a rate of 25 cents for every revolver. Smith & Wesson began production late in 1857, and enjoyed years of exclusive production of rear-loading cartridge revolvers in America due to their association with Rollin White, who held the patent and vigorously defended it against any perceived infringement by other manufacturers (much as Colt had done with his original patent on the revolver). Although White held the patent, other manufacturers were able to sell firearms using the design, provided they were willing to pay royalties.

After White's patent expired in April 1869, a third extension was refused. Other gun-makers were then allowed to produce their own weapons using the rear-loading method, without having to pay a royalty on each gun sold. Early guns were often conversions of earlier cap-and-ball revolvers, modified to accept metallic cartridges loaded from the rear, but later models, such as the Colt Model 1872 "open top" and the Smith & Wesson Model 3, were designed from the start as cartridge revolvers.

In 1873, Colt introduced the famous Model 1873, also known as the Single Action Army, the "Colt .45" (not to be confused with Colt-made models of the M1911 semi-automatic) or simply, "the Peacemaker", one of the most famous handguns ever made. This popular design, which was a culmination of many of the advances introduced in earlier weapons, fired 6 metallic cartridges and was offered in over 30 different calibers and various barrel lengths. It is still in production, along with numerous clones and lookalikes, and its overall appearance has remained the same since 1873. Although originally made for the United States Army, the Model 1873 was widely distributed and popular with civilians, ranchers, lawmen, and outlaws alike. Its design has influenced countless other revolvers. Colt has discontinued its production twice, but brought it back due to popular demand and continues to make it to this day.

In the U.S., the traditional single-action revolver still reigned supreme until the late 19th century. In Europe, however, arms makers were quick to adopt the double-action trigger. While the U.S. was producing weapons like the Model 1873, the Europeans were building double-action models like the French MAS Modèle 1873 and the somewhat later British Enfield Mk I and II revolvers (Britain relied on cartridge conversions of the earlier Beaumont–Adams double-action prior to this). Colt's first attempt at a double action revolver to compete with the European manufacturers was the Colt Model 1877, which earned lasting notoriety for its overly complex, expensive and fragile trigger mechanism, which in addition to failing frequently, also had a terrible trigger pull unless given the attentions of a competent gunsmith.

In 1889, Colt introduced the Model 1889, the first truly modern double action revolver, which differed from earlier double action revolvers by having a "swing-out" cylinder, as opposed to a "top-break" or "side-loading" cylinder. Swing out cylinders quickly caught on, because they combined the best features of earlier designs. Top-break actions gave the ability to eject all empty shells simultaneously, and exposed all chambers for easy reloading, but having the frame hinged into two halves weakened the gun and negatively affected accuracy, due to lack of rigidity. "Side-loaders", like the earlier Colt Model 1871 and 1873, gave a rigid frame, but required the user to eject and load one chamber at a time as they rotated the cylinder to line each chamber up with the side-mounted loading gate. Smith & Wesson followed seven years later with the Hand Ejector, Model 1896 in .32 S&W Long caliber, followed by the very similar, yet improved, Model 1899 (later known as the Model 10), which introduced the new .38 Special cartridge. The Model 10 went on to become the best selling handgun of the 20th century, at 6,000,000 units, and the .38 Special is still the most popular chambering for revolvers in the world. These new guns were an improvement over the Colt 1889 design since they incorporated a combined center-pin and ejector rod to lock the cylinder in position. The 1889 did not use a center pin and the cylinder was prone to move out of alignment.

Revolvers have remained popular to the present day in many areas, although in the military and law enforcement, they have largely been supplanted by magazine-fed semi-automatic pistols such as the Beretta M9 and the SIG Sauer M17, especially in circumstances where reload time and higher cartridge capacity are deemed important.

Patents

Elisha Collier of Boston, Massachusetts, patented a flintlock revolver in Britain in 1818, and significant numbers were being produced in London by 1822. The origination of this invention is in doubt, as similar designs were patented in the same year by Artemus Wheeler in the United States, and by Cornelius Coolidge in France. Samuel Colt submitted a British patent for his revolver in 1835 and an American patent (number 138) on February 25, 1836, for a ''Revolving gun'', and made the first production model on March 5 of that year.

Another revolver patent was issued to Samuel Colt on August 29, 1839. The February 25, 1836, patent was then reissued as entitled ''Revolving gun'' on October 24, 1848. This was followed by on September 3, 1850, for a ''Revolver'', and by on September 10, 1850, for a ''Revolver''. was issued to Roger C. Field for an economical device for minimizing the flash gap of a revolver between the barrel and the cylinder. In 1855, Rollin White patented the bored-through cylinder entitled ''Improvement in revolving fire-arms'' . In 1856, Horace Smith & Daniel Wesson formed a partnership (S&W), developed and manufactured a revolver chambered for a self-contained metallic cartridge.

Design

A revolver works by having several firing chambers arranged in a circle in a cylindrical block that are brought into alignment with the firing mechanism and barrel one at a time. In contrast, other repeating firearms, such as bolt-action, lever-action, pump-action, and semi-automatic, have a single firing chamber and a mechanism to load and extract cartridges into it.

A single-action revolver requires the hammer to be pulled back by hand before each shot, which also revolves the cylinder. This leaves the trigger with just one "single action" left to perform - releasing the hammer to fire the shot - so the force and distance required to pull the trigger can be minimal. In contrast, with a self-cocking revolver, one long squeeze of the trigger pulls back the hammer and revolves the cylinder, then finally fires the shot. They can generally be fired faster than a single-action, but with reduced accuracy in the hands of most shooters.

Most modern revolvers are "traditional double-action", which means they may operate either in single-action or self-cocking mode. The accepted meaning of "double-action" has, confusingly, come to be the same as "self-cocking", so modern revolvers that cannot be pre-cocked are called "double-action-only". These are intended for concealed carry, because the hammer of a traditional design is prone to snagging on clothes when drawn. Most revolvers do not come with accessory rails, which are used for mounting lights and lasers, except for the Smith & Wesson M&P R8 (.357 Magnum), Smith & Wesson Model 325 Thunder Ranch (.45 ACP), and all versions of the Chiappa Rhino (.357 Magnum, 9×19mm, .40 S&W, or 9×21mm) except for the 2" and 3" models, respectively. However, certain revolvers, such as the Taurus Judge and Charter Arms revolvers, can be fitted with accessory rails.

Most commonly, such revolvers have 5 or 6 chambers, hence the common names of "six-gun" or "six-shooter". However, some revolvers have 7, 8, 9, or 10 chambers, often depending on the caliber, and at least one revolver has 12 chambers (the US Fire Arms Model 12/22). Each chamber has to be reloaded manually, which makes reloading a revolver a much slower procedure than reloading a semi-automatic pistol.

Compared to autoloading handguns, a revolver is often much simpler to operate and may have greater reliability. For example, should a semiautomatic pistol fail to fire, clearing the chamber requires manually cycling the action to remove the errant round, as cycling the action normally depends on the energy of a cartridge firing. With a revolver, this is not necessary as none of the energy for cycling the revolver comes from the firing of the cartridge, but is supplied by the user either through cocking the hammer or, in a double-action design, by just squeezing the trigger. Another significant advantage of revolvers is superior ergonomics, particularly for users with small hands. A revolver's grip does not hold a magazine, and it can be designed or customized much more than the grip of a typical semi-automatic. Partially because of these reasons, revolvers still hold significant market share as concealed carry and home-defense weapons.

A revolver can be kept loaded and ready to fire without fatiguing any springs and is not very dependent on lubrication for proper firing. Additionally, in the case of double-action-only revolvers there is no risk of accidental discharge from dropping alone, as the hammer is cocked by the trigger pull. However, the revolver's clockwork-like internal parts are relatively delicate and can become misaligned after a severe impact, and its revolving cylinder can become jammed by excessive dirt or debris.

Over the long period of development of the revolver, many calibers have been used. Some of these have proved more durable during periods of standardization and some have entered general public awareness. Among these are the .22 rimfire, a caliber popular for target shooting and teaching novice shooters; .38 Special and .357 Magnum, known for police use; the .44 Magnum, famous from Clint Eastwood's '' Dirty Harry'' films; and the .45 Colt, used in the Colt revolver of the Wild West. Introduced in 2003, the Smith & Wesson Model 500 is one of the most powerful revolvers, utilizing the .500 S&W Magnum cartridge.

Because the rounds in a revolver are headspaced on the rim, some revolvers are capable of chambering more than one type of ammunition. The .44 Magnum round will also chamber the .44 Special and .44 Russian, and .38 Short Colt. In 1996, a revolver known as the Medusa M47 was made that could chamber 25 different cartridges with bullet diameters between .355" and .357".

Revolver technology lives on in other weapons used by the military. Some autocannons and grenade launchers use mechanisms similar to revolvers, and some riot shotguns use spring-loaded cylinders holding up to 12 rounds. In addition to serving as backup guns, revolvers still fill the specialized niche role as a shield gun; law enforcement personnel using a "bulletproof" gun shield sometimes opt for a revolver instead of a self-loading pistol, because the slide of a pistol may strike the front of the shield when fired. Revolvers do not suffer from this disadvantage. A second revolver may be secured behind the shield to provide a quick means of continuity of fire. Many police also still use revolvers as their duty weapon due to their relative mechanical simplicity and user friendliness.

With the advancement of technology and design in 2010, major revolver manufacturers started producing polymer frame revolvers like the Ruger LCR, Smith & Wesson Bodyguard 38, and Taurus Protector Polymer. The new innovative design incorporates advanced polymer technology that lowers weight significantly, helps absorbs recoil, and strong enough to handle .38 Special +P and .357 Magnum loads. The polymer is only used on the lower frame and joined to a metal alloy upper frame, barrel, and cylinder. Polymer technology is considered one of the major advancements in revolver history because the frame has always been metal alloy and mostly a one piece frame design.

Another recent development in revolver technology is the Chiappa Rhino, a revolver introduced by Italian manufacturer Chiappa in 2009, and first sold in the U.S. in 2010. The Rhino, built with the U.S. concealed carry market in mind, is designed so the bullet fires from the bottom chamber of the cylinder instead of the top chamber as in standard revolvers. This is intended to reduce muzzle flip, allowing for faster and more accurate repeat shots. In addition, the cylinder cross-section is hexagonal instead of circular, further reducing the weapon's profile.

Loading and unloading

Front-loading cylinder

The first revolvers were ''front loading'' (also referred to as muzzleloading), and were a bit like muskets in that the powder and bullet were loaded separately. These were caplocks or "cap and ball" revolvers, because the caplock method of priming was the first to be compact enough to make a practical revolver feasible. When loading, each chamber in the cylinder was rotated out of line with the barrel, and charged from the front with loose powder and an oversized bullet. Next, the chamber was aligned with the ramming lever underneath the barrel. Pulling the lever would drive a rammer into the chamber, pushing the ball securely in place. Finally, the user would place percussion caps on the nipples on the rear face of the cylinder.

After each shot, a user was advised to raise his revolver vertically while cocking back the hammer so as to allow the fragments of the spent percussion cap to fall out safely. Otherwise, the fragments could fall into the revolver's mechanism and jam it. Caplock revolvers were vulnerable to "chain fires", wherein hot gas from a shot ignited the powder in the other chambers. This could be prevented by sealing the chambers with cotton, wax, or grease. Chain fire led to the shots hitting the shooters hand, which is one of the main reasons why revolver rifles were uncommon. By the time metallic cartridges became common, more effective mechanisms for a repeating rifle, such as lever-action, had been developed.

Loading a cylinder in this manner was a slow and awkward process and generally could not be done in the midst of battle. Some soldiers solved this by carrying multiple revolvers in the field. Another solution was to use a revolver with a detachable cylinder design. These revolvers allowed the shooter to quickly remove a cylinder and replace it with a full one.

Fixed cylinder designs

In many of the first generation of cartridge revolvers (especially those that were converted after manufacture), the base pin on which the cylinder revolved was removed, and the cylinder taken from the revolver for loading. Most revolvers using this method of loading are single-action revolvers, although Iver Johnson produced double-action models with removable cylinders. The removable-cylinder design is employed in some modern "micro-revolvers" (usually chambered in .22 rimfire), in order to simplify their design. These weapons are small enough to fit in the palm of the hand.

Later single-action revolver models with a fixed cylinder used a loading gate at the rear of the cylinder that allowed insertion of one cartridge at a time for loading, while a rod under the barrel could be pressed rearward to eject the fired case.

The loading gate on the original Colt designs (and on nearly all single-action revolvers since, such as the famous Colt Single Action Army) is on the right side, which was done to facilitate loading while on horseback; with the revolver held in the left hand with the reins of the horse, the cartridges can be ejected and loaded with the right hand.

Because the cylinders in these types of revolvers are firmly attached at the front and rear of the frame, and the frame is typically full thickness all the way around, fixed cylinder revolvers are inherently strong designs. Accordingly, many modern large caliber hunting revolvers tend to be based on the fixed cylinder design. Fixed cylinder revolvers can fire the strongest and most powerful cartridges, but at the price of being the slowest to load or unload, as they cannot use speedloaders or moon clips for loading, as only one chamber is exposed at a time to the loading gate.

Top-break cylinder

In a top-break revolver, the frame is hinged at the bottom front of the cylinder. Releasing the lock and pushing the barrel down exposes the rear face of the cylinder. In most top-break revolvers, this act also operates an extractor that pushes the cartridges in the chambers back far enough that they will fall free, or can be removed easily. Fresh rounds are then inserted into the cylinder. The barrel and cylinder are then rotated back and locked in place, and the revolver is ready to fire.

Top-break revolvers are able to be loaded more rapidly than fixed frame revolvers, especially with the aid of a speedloader or moon clip. However, this design is much weaker and cannot handle high pressure rounds. While this design is mostly obsolete today, supplanted by the stronger yet equally convenient swing-out cylinder design, manufacturers have begun making reproductions of late 19th century designs for use in cowboy action shooting.

The first top-break revolver was patented in France and Britain at the end of December in 1858 by Devisme. The most commonly found top-break revolvers were manufactured by Smith & Wesson, Webley & Scott, Iver Johnson, Harrington & Richardson, Manhattan Fire Arms, Meriden Arms and Forehand & Wadsworth.

Tip-up cylinder

The tip-up revolver was the first design to be used with metallic cartridges in the Smith & Wesson Model 1, on which the barrel pivoted upwards, hinged on the forward end of the topstrap. On the S&W tip-up revolvers, the barrel release catch is located on both sides of the frame in front of the trigger. Smith & Wesson discontinued it in the third series of the Smith & Wesson Model 1 1/2 but it was fairly widely used in Europe in the 19th century, after a patent by Spirlet in 1870, which also included an ejector star.

Swing-out cylinder

The most modern method of loading and unloading a revolver is by means of the ''swing-out cylinder''. The first swing-out cylinder revolver was patented in France and Britain at the end of December in 1858 by Devisme. The cylinder is mounted on a pivot that is parallel to the chambers, and the cylinder swings out and down (to the left in most cases). An extractor is fitted, operated by a rod projecting from the front of the cylinder assembly. When pressed, it will push all fired rounds free simultaneously (as in top-break models, the travel is designed to not completely extract longer, unfired rounds). The cylinder may then be loaded, individually or again with the use of a speedloader, closed, and latched in place.

The pivoting part that supports the cylinder is called the crane; it is the weak point of swing-out cylinder designs. Using the method often portrayed in movies and television of flipping the cylinder open and closed with a flick of the wrist can in fact cause the crane to bend over time, throwing the cylinder out of alignment with the barrel. Lack of alignment between chamber and barrel is a dangerous condition, as it can impede the bullet's transition from chamber to barrel. This gives rise to higher pressures in the chamber, bullet damage, and the potential for an explosion if the bullet becomes stuck.

The shock of firing can exert a great deal of stress on the crane, as in most designs the cylinder is only held closed at one point, the rear of the cylinder. Stronger designs, such as the Ruger Super Redhawk, use a lock in the crane as well as the lock at the rear of the cylinder. This latch provides a more secure bond between cylinder and frame, and allows the use of larger, more powerful cartridges. Swing-out cylinders are rather strong, but not as strong as fixed cylinders, and great care must be taken with the cylinder when loading, so as not to damage the crane.

Other designs

One unique design was designed by Merwin Hulbert in which the barrel and cylinder assembly were rotated 90° and pulled forward to eject shells from the cylinder.

Action

Single-action

In a single-action revolver, the hammer is manually cocked, usually with the thumb of the firing or supporting hand. This action advances the cylinder to the next round and locks the cylinder in place with the chamber aligned with the barrel. The trigger, when pulled, releases the hammer, which fires the round in the chamber. To fire again, the hammer must be manually cocked again. This is called "single-action" because the trigger only performs a single action, of releasing the hammer. Because only a single action is performed and trigger pull is lightened, firing a revolver in this way allows most shooters to achieve greater accuracy. Additionally, the need to cock the hammer manually acts as a safety. Unfortunately with some revolvers, since the hammer rests on the primer or nipple, accidental discharge from impact is more likely if all 6 chambers are loaded. The Colt Paterson, Colt Walker, Colt Dragoon, and Colt Single Action Army of the American frontier era are all good examples of this system.

Double-action

In double-action (DA), the stroke of the trigger pull generates two actions:
#The hammer is pulled back to the cocked position which also indexes the cylinder to the next round.
#The hammer is released to strike the firing pin.
Thus, DA means that a cocking action separate from the trigger pull is unnecessary; every trigger pull will result in a complete cycle. This allows uncocked carry, while also allowing draw-and-fire using only the trigger. A longer and harder trigger stroke is the trade-off. However, this drawback can also be viewed as a safety feature, as the gun is safer against accidental discharges from being dropped.

Most double-action revolvers may be fired in two ways.
# The first way is single-action; that is, exactly the same as a single-action revolver; the hammer is cocked with the thumb, which indexes the cylinder, and when the trigger is pulled, the hammer is tripped.
# The second way is double-action, or from a hammer-down position. In this case, the trigger first cocks the hammer and revolves the cylinder, then trips the hammer at the rear of the trigger stroke, firing the round in the chamber.

Certain revolvers, called ''double-action-only'' (DAO) or, more correctly but less commonly, ''self-cocking'', lack the latch that enables the hammer to be locked to the rear, and thus can only be fired in the double-action mode. With no way to lock the hammer back, DAO designs tend to have ''bobbed'' or ''spurless'' hammers, and may even have the hammer completely covered by the revolver's frame (i.e., shrouded or hooded). These are generally intended for concealed carrying, where a hammer spur could snag when the revolver is drawn. The potential reduction in accuracy in aimed fire is offset by the increased capability for concealment.

DA and DAO revolvers were the standard-issue sidearm of countless police departments for many decades. Only in the 1980s and 1990s did the semiautomatic pistol begin to make serious inroads after the advent of safe actions. The reasons for these choices are the modes of carry and use. Double action is good for high-stress situations because it allows a mode of carry in which "draw and pull the trigger" is the only requirement—no safety catch release nor separate cocking stroke is required.

Other

In the cap-and-ball days of the mid 19th century, two revolver models, the English Tranter and the American Savage "Figure Eight", used a method whereby the hammer was cocked by the shooter's middle finger pulling on a second trigger below the main trigger.

Iver Johnson made an unusual model from 1940 to 1947 called the ''Trigger Cocking Double Action''. If the hammer was down, pulling the trigger would cock the hammer. If the trigger was pulled with the hammer cocked, it would then fire. This meant that to fire the revolver from a hammer down state, the trigger must be pulled twice.

3D printed revolver

The Zig zag revolver

HOME


Content is Copyleft
Website design, code, and AI is Copyrighted (c) 2014-2017 by Stephen Payne


Consider donating to Wikimedia



As an Amazon Associate I earn from qualifying purchases