The near–far problem or hearability problem is the effect of a strong signal from a near signal source in making it hard for a receiver to hear a weaker signal from a further source due to
adjacent-channel interference,
co-channel interference,
distortion
In signal processing, distortion is the alteration of the original shape (or other characteristic) of a signal. In communications and electronics it means the alteration of the waveform of an information-bearing signal, such as an audio signal ...
,
capture effect,
dynamic range limitation, or the like. Such a situation is common in wireless communication systems, in particular
CDMA. In some
signal jamming techniques, the near–far problem is exploited to disrupt ("
jam") communications.
Analogies
Consider a receiver and two transmitters, one close to the receiver, the other far away. If both transmitters transmit simultaneously and at equal powers, then due to the
inverse square law the receiver will receive more power from the nearer transmitter. Since one transmission's
signal
A signal is both the process and the result of transmission of data over some media accomplished by embedding some variation. Signals are important in multiple subject fields including signal processing, information theory and biology.
In ...
is the other's
noise
Noise is sound, chiefly unwanted, unintentional, or harmful sound considered unpleasant, loud, or disruptive to mental or hearing faculties. From a physics standpoint, there is no distinction between noise and desired sound, as both are vibrat ...
, the
signal-to-noise ratio (SNR) for the further transmitter is much lower. This makes the farther transmitter more difficult, if not impossible, to understand. In short, the near–far problem is one of detecting or filtering out a weaker signal amongst stronger signals.
To place this problem in more common terms, imagine you are talking to someone 6 meters away. If the two of you are in a quiet, empty room then a conversation is quite easy to hold at normal voice levels. In a loud, crowded bar, it would be impossible to hear the same voice level, and the only solution (for that distance) is for both you and your friend to speak louder. Of course, this increases the overall noise level in the bar, and every other patron has to talk louder too (this is equivalent to power control runaway). Eventually, everyone has to shout to make themselves heard by a person standing right beside them, and it is impossible to communicate with anyone more than half a meter away. In general, however, a human is very capable of filtering out loud sounds; similar techniques can be deployed in signal processing where suitable criteria for distinguishing between signals can be established (see
signal processing
Signal processing is an electrical engineering subfield that focuses on analyzing, modifying and synthesizing ''signals'', such as audio signal processing, sound, image processing, images, Scalar potential, potential fields, Seismic tomograph ...
and notably
adaptive signal processing).
Taking this analogy back to wireless communications, the far transmitter would have to drastically increase transmission power which simply may not be possible.
Solutions
In
CDMA systems and similar
cellular phone-like networks, the problem is commonly solved by dynamic output power adjustment of the transmitters. That is, the closer transmitters use less power so that the SNR for all transmitters at the receiver is roughly the same. This sometimes can have a noticeable impact on battery life, which can be dramatically different depending on distance from the base station. In high-noise situations, however, closer transmitters may boost their output power, which forces distant transmitters to boost their output to maintain a good SNR. Other transmitters react to the rising noise floor by increasing their output. This process continues, and eventually distant transmitters lose their ability to maintain a usable SNR and drop from the network. This process is called ''power control runaway''. This principle may be used to explain why an area with low signal is perfectly usable when the cell isn't heavily loaded, but when load is higher, service quality degrades significantly, sometimes to the point of unusability.
Other possible solutions to the near–far problem:
# Increased receiver dynamic range - Use a higher resolution ADC. Increase the dynamic range of receiver stages that are saturating.
# Dynamic output power control – Nearby transmitters decrease their output power so that all signals arrive at the receiver with similar signal strengths.
# TDMA – Transmitters use some scheme to avoid transmitting at the same time.
See also
*
Direct-sequence spread spectrum
*
Hidden node problem
In wireless networking, the hidden node problem or hidden terminal problem occurs when a Node (networking), node can communicate with a wireless access point (AP), but cannot directly communicate with other nodes that are communicating with that ...
*
Signal-to-noise ratio
References
{{DEFAULTSORT:Near-far problem
Signal processing
Code division multiple access