Multi-threshold CMOS (MTCMOS) is a variation of
CMOS
Complementary metal–oxide–semiconductor (CMOS, pronounced "sea-moss", ) is a type of metal–oxide–semiconductor field-effect transistor (MOSFET) fabrication process that uses complementary and symmetrical pairs of p-type and n-type MOSF ...
chip technology which has
transistor
upright=1.4, gate (G), body (B), source (S) and drain (D) terminals. The gate is separated from the body by an insulating layer (pink).
A transistor is a semiconductor device used to Electronic amplifier, amplify or electronic switch, switch ...
s with multiple
threshold voltage
The threshold voltage, commonly abbreviated as Vth or VGS(th), of a field-effect transistor (FET) is the minimum gate-to-source voltage (VGS) that is needed to create a conducting path between the source and drain terminals. It is an important s ...
s (V
th) in order to optimize delay or power. The V
th of a
MOSFET
The metal–oxide–semiconductor field-effect transistor (MOSFET, MOS-FET, or MOS FET) is a type of field-effect transistor (FET), most commonly fabricated by the controlled oxidation of silicon. It has an insulated gate, the voltage of which d ...
is the gate voltage where an
inversion layer forms at the interface between the insulating layer (oxide) and the substrate (body) of the transistor. Low V
th devices switch faster, and are therefore useful on critical delay paths to minimize clock periods. The penalty is that low V
th devices have substantially higher static leakage power. High V
th devices are used on non-critical paths to reduce static leakage power without incurring a delay penalty. Typical high V
th devices reduce static leakage by 10 times compared with low V
th devices.
One method of creating devices with multiple threshold voltages is to apply different bias voltages (Vb) to the base or bulk terminal of the transistors. Other methods involve adjusting the
gate oxide thickness, gate oxide
dielectric
In electromagnetism, a dielectric (or dielectric medium) is an electrical insulator that can be polarised by an applied electric field. When a dielectric material is placed in an electric field, electric charges do not flow through the ma ...
constant (material type), or
dopant
A dopant, also called a doping agent, is a trace of impurity element that is introduced into a chemical material to alter its original electrical or optical properties. The amount of dopant necessary to cause changes is typically very low. Whe ...
concentration in the channel region beneath the gate oxide.
A common method of fabricating multi-threshold CMOS involves simply adding additional
photolithography
In integrated circuit manufacturing, photolithography or optical lithography is a general term used for techniques that use light to produce minutely patterned thin films of suitable materials over a substrate, such as a silicon wafer, to protec ...
and
ion implantation
Ion implantation is a low-temperature process by which ions of one element are accelerated into a solid target, thereby changing the physical, chemical, or electrical properties of the target. Ion implantation is used in semiconductor device fa ...
steps. For a given fabrication process, the V
th is adjusted by altering the concentration of dopant atoms in the channel region beneath the gate oxide. Typically, the concentration is adjusted by
ion implantation
Ion implantation is a low-temperature process by which ions of one element are accelerated into a solid target, thereby changing the physical, chemical, or electrical properties of the target. Ion implantation is used in semiconductor device fa ...
method. For example,
photolithography
In integrated circuit manufacturing, photolithography or optical lithography is a general term used for techniques that use light to produce minutely patterned thin films of suitable materials over a substrate, such as a silicon wafer, to protec ...
methods are applied to cover all devices except the p-MOSFETs with photoresist. Ion implantation is then completed, with ions of the chosen dopant type penetrating the gate oxide in areas where no photoresist is present. The photoresist is then stripped. Photolithography methods are again applied to cover all devices except the n-MOSFETs. Another implantation is then completed using a different dopant type, with ions penetrating the gate oxide. The photoresist is stripped. At some point during the subsequent fabrication process, implanted ions are activated by annealing at an elevated temperature.
In principle, any number of threshold voltage transistors can be produced. For CMOS having two threshold voltages, one additional photomasking and implantation step is required for each of p-MOSFET and n-MOSFET. For fabrication of normal, low, and high V
th CMOS, four additional steps are required relative to conventional single-V
th CMOS.
Implementation
The most common implementation of MTCMOS for reducing
power
Power most often refers to:
* Power (physics), meaning "rate of doing work"
** Engine power, the power put out by an engine
** Electric power
* Power (social and political), the ability to influence people or events
** Abusive power
Power may a ...
makes use of sleep transistors. Logic is supplied by a virtual
power rail
A third rail, also known as a live rail, electric rail or conductor rail, is a method of providing electric power to a railway locomotive or train, through a semi-continuous rigid conductor placed alongside or between the rails of a railway t ...
. Low V
th devices are used in the logic where fast switching speed is important. High V
th devices connecting the power rails and virtual power rails are turned on in active mode, off in
sleep mode. High V
th devices are used as sleep transistors to reduce static leakage power.
The design of the power
switch
In electrical engineering, a switch is an electrical component that can disconnect or connect the conducting path in an electrical circuit, interrupting the electric current or diverting it from one conductor to another. The most common type of ...
which turns on and off the
power supply
A power supply is an electrical device that supplies electric power to an electrical load. The main purpose of a power supply is to convert electric current from a source to the correct voltage, current, and frequency to power the load. As ...
to the
logic gate
A logic gate is an idealized or physical device implementing a Boolean function, a logical operation performed on one or more binary inputs that produces a single binary output. Depending on the context, the term may refer to an ideal logic ga ...
s is essential to low-voltage, high-speed
circuit techniques such as MTCMOS. The speed, area, and power of a logic circuit are influenced by the characteristics of the power switch.
In a "coarse-grained" approach, high V
th sleep transistors gate the power to entire logic blocks. The sleep signal is de-asserted during active mode, causing the transistor to turn on and provide virtual power (ground) to the low V
th logic. The sleep signal is asserted during
sleep mode, causing the transistor to turn off and disconnect power (ground) from the low V
th logic. The drawbacks of this approach are that:
* logic blocks must be partitioned to determine when a block may be safely turned off (on)
* sleep transistors are large and must be carefully sized to supply the current required by the circuit block
* an always active (never in sleep mode) power management circuit must be added
In a "fine-grained" approach, high V
th sleep transistors are incorporated within every gate. Low V
th transistors are used for the pull-up and pull-down networks, and a high V
th transistor is used to gate the leakage current between the two networks. This approach eliminates problems of logic block partitioning and sleep transistor sizing. However, a large amount of area overhead is added due both to inclusion of additional transistors in every
Boolean gate, and in creating a sleep signal distribution tree.
An intermediate approach is to incorporate high V
th sleep transistors into threshold gates having more complicated function. Since fewer such threshold gates are required to implement any arbitrary function compared to Boolean gates, incorporating MTCMOS into each gate requires less area overhead. Examples of threshold gates having more complicated function are found with Null Convention Logic and Sleep Convention Logic.
Some art is required to implement MTCMOS without causing glitches or other problems.
References
{{DEFAULTSORT:Multi-Threshold Cmos
Electronic design
Digital electronics
Logic families