Large aircraft

Large aircraft allow the transportation of large and/or heavy payloads over long distances. Making an aircraft design larger can also improve the overall fuel efficiency and man-hours for transporting a given load, while a greater space is available for transporting lightweight cargoes or giving passengers room to move around. However, as aircraft increase in size they pose significant design issues not present in smaller types. These include structural efficiency, flight control response and sufficient power in a reliable and cost-effective installation.

Large aircraft also require specialised ground facilities, and some countries have special regulatory environments for them.

The giant airships of the 1930s remain, as of 2016, the largest aircraft ever constructed, while the Hughes H-4 "Spruce Goose" of 1947 had the largest wingspan of any fixed-wing type. The Hybrid Air Vehicles Airlander 10 hybrid airship is the largest aircraft flying today.

Characteristics

Payload space

The lifting capacity of an aircraft depends on the wing size and its "loading", the weight per unit area that the wing can support. Loading is more or less constant for a given level of technology. Thus, as aircraft size increases the lifting capacity increases with the surface area. For a given aerodynamic form, the area in turn increases with the square of the wing span. If structural efficiency can be maintained, the structural weight of the airframe also increases with its surface area and the square of the span. But the internal volume increases with the cube of the span.

For example, if the dimensions are all doubled in size, then the area and lifting capacity increase 2 × 2 = 4 times, while the volume increases 2 × 2 × 2 = 8 times.

For a passenger aircraft, this doubling in size allows up to twice the cabin space per passenger. Alternatively, for a transport it allows up to twice the space to fit in bulky but light cargo. Thus, large aircraft are both more comfortable and operationally flexible in use than smaller types.

Structure

Although a larger wing carries larger forces, it is also thicker. The main spar in the wing approximates an I-beam, whose depth equals the wing thickness. For a given overall load to be carried, the forces in the beam decrease with the square of its depth. If a wing is doubled in span it is also doubled in thickness. This reduces the forces in the spar by a factor of 2 x 2 = 4, allowing a fourfold increase in the overall load. This exactly matches the increased lift available from the larger wing area.

This means that the metal parts of a large aircraft need be no thicker or heavier than those of a smaller aircraft. However, because these parts must cover four times the area they make the aircraft four times heavier. This again exactly matches the increase in laden weight, so there is no structural limit to how large (or small) an aeroplane can be made.

Large aircraft do still pose a design challenge. The structural members may be no thicker, but they are now twice as long, so stiffness becomes a problem, and the design approach must be adapted to ensure adequate overall stiffness. This is typically achieved by making structural members cellular. For example, the wing spar in a small aircraft may in fact be a simple I-beam with a solid cross-section, but in a larger design the upright part of the beam or "web" will be constructed as an open lattice of trusses in a triangulated structure.

Flight control

The effectiveness of a flight control such as an aileron depends mainly on its area and its distance from the centre of the aircraft - its lever arm. If the wingspan is doubled, the area increases fourfold and the lever arm doubles, making the aileron 8 times more effective.

With the aircraft being also four times heavier, and with the weight on average twice as far out, it requires 8 times the effort to achieve the same acceleration of the wing tip.

These balance out, so on a large aircraft the equivalent aileron will accelerate the wing tip up or down at the same speed as a smaller aircraft. But on a wing twice the span, the tip must travel twice as far to achieve the same change in aircraft attitude. This takes longer, so a large aircraft manoeuvres more slowly than the equivalent smaller aircraft.

On very large types such as the Airbus A380, conventional ailerons alone are not enough, and additional lift spoilers are used to reduce the lift of the downward-tipping wing and increase the roll rate to a practical and safe level.

Similar issues occur with the elevator and pitch control. Without extra design measures to ensure adequate control response, any attempt to make a last-minute correction to the flight path is likely to prove too little too late, making a last-minute landing abort and fly-around difficult and dangerous.

Engines

The number of engines on an aircraft affects its reliability and safety. The more engines there are, the safer it is if one engine fails. But on the other hand, the more engines there are, the more likely there is to be a failure of one or more and the greater the workload on the flight engineer. Nowadays, two engines are preferred in practice, with even quite large wide-body aircraft having only two engines. Four is generally accepted as the limit, for both safety and cost reasons.

Barring a few military types, no practical large aircraft has ever had more than four engines. As aircraft get bigger, it therefore becomes necessary to design bigger engines.

The airspeed of a fan blade must be kept below the speed of sound in order to avoid damaging and noisy shock waves. This maximum speed of the tip sets a limit on the rate of rotation. For a given rate of rotation, the tip of a larger fan will travel faster. So to keep down the top speed of a large engine, the fan must spin more slowly. The fan is driven by a turbine off the same shaft, so the turbine blades also spin round more slowly.

Operations

In practice, the operational savings inherent in flying fewer aircraft make larger types more economical on routes which can sustain their size.

However, ground facilities such as runways, handling facilities and hangars must be enlarged to cope, and the expense of this must be offset against the lower operating cost. The limited width available at some airports restricts the wing span achievable on a practical aircraft.

Regulatory definitions

In the regulation of air activity, authorities pose additional rules and restrictions on types above a certain size.

The American Federal Aviation Administration defines a large aircraft as any aircraft of more than maximum certificated takeoff weight.

The European Aviation Safety Agency (EASA) defines a large aircraft as either "an aeroplane with a maximum take-off mass of more than , a multi-engined helicopter or a gas airship with a volume of more than 15 000 m3."

History

The first practical aircraft were balloons, used for sport and for military observation. In 1901 the giant balloon ''Preusen'' (Prussia) of rose to a height of . Early airships were little more than elongated balloons with an engine slung underneath. These craft were limited in size because their bodies were non-rigid and could not be made too long. The German Count Ferdinand von Zeppelin realised that a rigid frame could support a much larger volume, and in 1900 the Luftschiff Zeppelin 1 of volume and length took briefly to the air.Ege, L,; "Balloons and Airships", Blandford (1973).

Early fixed-wing aeroplanes were mostly single-engined. When the Russian Igor Sikorsky designed and flew his Ilya Muromets in 1913 it became not only the first four-engined aircraft but, with a wing span of and laden weight of , by far the largest and heaviest to date. By comparison the LZ 18 airship, which flew the same year, was long (the envelope had a capacity of ) and an empty weight of 20 tonnes.

The Beardmore Inflexible of 1928 had a wingspan of and an all up weight of 37,000 lbs. However it was underpowered for such a heavy aircraft. It was structurally advanced for its time, being of all-metal stressed-skin construction.''Air Enthusiast International'' March 1974, p.145. The Dornier Do X was the largest, heaviest, and most powerful flying boat in the world when it flew in 1929, having a similar span of 48 m (157 ft 6 in) and a maximum takeoff weight of 56,000 kg (123,459 lb).

During the years between the two World Wars, only the Soviet Tupolev ANT-20 ''Maxim Gorki'' landplane of 1934 was larger at 63.00 m (206 ft 9 in) span, but at 53 metric tons maximum takeoff weight it was not as heavy as the Do X's 56 tonnes.

The largest airship ever built was the Zeppelin LZ 129 "Hindenburg". First flying in 1936, the Hindenburg had a volume of and a length of . Its maximum payload, of combined passengers and freight, was . Following the Hindenburg's disastrous end, no airships of this scale have since been built.

By then, larger aeroplanes—especially long-distance flying boats—had exceeded the Ilya Muromets in scale. Then, during World War II, America foresaw a requirement for a large trans-Pacific cargo carrier able to operate from bases with no prepared landing strip. The giant Hughes H-4 Hercules flying boat was constructed from timber, earning it the name the "Spruce Goose". When finally flown briefly in 1947, its wingspan made it the largest plane ever to fly, and it has never been equalled. It required 8 Pratt & Whitney R-4360 Wasp Major radial engines to get it into the air. By then, the landplane had taken over long-distance flight and the H-4 - having made no more than a single mile-long flight less than 100 ft off the water - never flew again. It is today preserved as a museum piece.

At the start of the Second World War, Barnes Wallis proposed a "Victory Bomber" of 50 tonnes to carry a 10-tonne bomb but it was discounted by the Air Ministry because of its limited application. As the war progressed the British contemplated very large bomber designs (from 75 to 100 tonnes with bombloads of 25 tonnes and six or more engines) but considered the time required to bring them into use, the difficulty of balancing bombload, defensive armament and range, and the success of existing designs (such as the Avro Lancaster) to outweigh any advantages. Some of the work on large aircraft fed into the post-war Bristol Brabazon a 70-m wingspan 130-tonne airliner which would have given its 100 passengers ship-like levels of space and comfort.

With the arrival of the jet age, airliners continued to increase in size. Wide-body types were introduced and, in 1970, the Boeing 747 "Jumbo jet" entered service. It featured a short second, upper deck to provide increased passenger accommodation. Variants of the 747 remained the largest airliners flying for well over thirty years, some with a "stretched" upper deck, until the arrival of the Airbus A380 series in 2007 featuring a full-length upper deck. Both lines continue to be developed, with ever-larger variants being introduced. The largest is currently (2014) the A380-800, capable of seating up to 853 people.

In order to airlift the Buran space shuttle, in 1988 Soviet Union introduced the sole Antonov An-225 Mriya (''dream''). With a (maximum takeoff weight greater than and a wing span of , it was the largest operational aeroplane in the world. Since the conclusion of Buran flights, the Mriya remained in service as a heavy transport plane until it's destruction in the Battle of Antonov Airport during the 2022 Russian invasion of Ukraine.

The largest aircraft of any kind flying today (2014) is the Hybrid Air Vehicles Airlander 10 hybrid airship, with an internal capacity of 38,000 cubic metres and a length of 91 m.

Lists of largest aircraft

See also

* List of large aircraft
*List of transport megaprojects

References

{{reflist, 2

Aircraft by design configuration