Keystroke programming describes a specific way of programming by which each keystroke on a device or application is recorded in some way and then played back so that the recorded key-presses can be repeated multiple times. Keystroke programming is most commonly but not exclusively found in
programmable calculator
Programmable calculators are calculators that can automatically carry out a sequence of operations under control of a stored computer programming, program. Most are Turing complete, and, as such, are theoretically general-purpose computers. Howe ...
s, but there are keystroke-programmable software applications, too, for example
Vim (text editor)
Vim (;
"Vim is pronounced as one word, like Jim, not vi-ai-em. It's written with a capital, since it's a name, again like Jim." ...
Example: TI Calculators
![TI58c](https://upload.wikimedia.org/wikipedia/commons/7/71/TI58c.jpg)
The Texas Instruments
TI-58
The TI-59 is an early programmable calculator, that was manufactured by Texas Instruments from 1977. It is the successor to the TI SR-52, quadrupling the number of "program steps" of storage, and adding "ROM Program Modules" (an insertable ROM ...
/
TI-58C
The TI-59 is an early programmable calculator, that was manufactured by Texas Instruments from 1977. It is the successor to the TI SR-52, quadrupling the number of "program steps" of storage, and adding "ROM Program Modules" (an insertable ROM ...
/
TI-59
The TI-59 is an early programmable calculator, that was manufactured by Texas Instruments from 1977. It is the successor to the TI SR-52, quadrupling the number of "program steps" of storage, and adding "ROM Program Modules" (an insertable ROM ...
calculators were programmable, and program storage took the form of a sequence of codes which (mostly) corresponded to the position of keys on the calculator keypad. Here is a simplified diagram of the basic key layout:
Each key is assigned a two-digit code; for most (but not all) keys, the tens digit comes from the row number (as indicated down the left of the table) and the units digit comes from the column number (as indicated across the top of the table).
Now consider a very simple program, which adds 2 to the number being displayed, and then stops. The program is entered starting from program location 000, and looks like this:
To use this program, you would enter the number ''n'' to be operated on, press to ensure the current program location was 000, then to start execution. When the program stops (which should happen quite quickly for such a simple program), the display will be showing the number ''n'' + 2.
You can see that the codes 85, 95 and 91 correspond to the positions of the keys labelled , and on the grid above, but the code for the is not 83 as you would expect from the grid position, but 02. This last code was chosen to be more easily understandable by a human trying to read the program. There is no row 0, so the codes 00 .. 09 are used to represent the keys .. .
Context-Dependent Interpretations
These TI calculators allowed for addressing up to 100 data memory locations, numbered 00 to 99 (some models had a lower limit than this). A keystroke sequence like (store the currently-displayed number into memory 42) would be encoded as 42 42. In this case the first 42 is the key code for the key, but the second 42 is not a key code, but a memory register number. The calculator knows to interpret it as such because that's what has to follow the code for the key.
Program addresses were 3 digits, potentially allowing programs to consist of up to 1000 steps, numbered 000 to 999 (though in fact none of the models produced allowed for this maximum). A branch instruction, for example (unconditional branch to location 345) would be encoded as 61 03 45. In this case the hundreds digit of the branch destination is in the units digit of the second instruction byte (after the opcode), with a zero tens digit; and the remaining digits are in the third instruction byte.
A code sequence like 61 11, on the other hand, represents the keystrokes , which is a branch to the location marked by the ''symbolic label'' . The calculator can tell this is a symbolic branch, rather than a branch to a numbered location, because the tens digit of the byte immediately following the opcode is not zero.
Most of the keys on the keypad can be used as symbolic labels. For example, sequences like and are legitimate, provided that and have in fact been defined as labels somewhere in the program.
Modifier Keys
Most of the keys had multiple functions, depending on whether or had been pressed beforehand. invoked the "inverse" (whatever that meant) of the following function, and was recorded in a program as a separate keystroke (code 22), while invoked a completely different function which was written on the keypad faceplate just above the key. For example, pressing invoked the function, while (or ) gave you the arcsine.
The code for this alternate function is derived from that of the original key function by adding 5 to the units digit (''without'' carry to the tens digit). Thus, the key codes corresponding to the position of the key itself (21 and 26) are never used as opcodes. Here is the table of the codes produced with the prefix:
Merged Keystrokes
The key allows for indirection: wherever a reference to a memory register or a program location is allowed, this key can be used to fetch the actual value from a memory register. For example, the key sequence means to fetch the value in memory register 10, and use that value in turn as the number of a memory register whose contents are to be fetched as the current operand. However, in this case the cannot be encoded as code 40, because the code sequence 43 40 would be interpreted as , not .
But, because of the use of the 00 .. 09 codes for the .. keys, the codes 62-64, 72-74, 82-84 and 92 are available for other uses. So most of these are reallocated to represent ''op'' sequences:
Thus, the key sequence would be encoded as 73 10.
Note the use of code 92 for {{TI-5x/Keys/Brown, SBR (return from subroutine); this was not necessary for reasons of ambiguity, but was done to save space with such a common sequence.
See also
*
FOCAL keystroke programming
The HP-41C series are programmable, expandable, continuous memory handheld RPN calculators made by Hewlett-Packard from 1979 to 1990. The original model, HP-41C, was the first of its kind to offer alphanumeric display capabilities. Later cam ...
*
Macro recorder
A macro recorder is software that records macros for playback at a later time.
The main advantage of using a macro recorder is that it allows a user to easily perform complex operations much faster and with less effort without requiring custom co ...
*
Programming by demonstration
In computer science, programming by demonstration (PbD) is an end-user development technique for teaching a computer or a robot new behaviors by demonstrating the task to transfer directly instead of programming it through machine commands.
The te ...
References
Programmable calculators