SAE J1772, also known as a J plug or Type 1 connector after its international standard, IEC 62196 Type 1, is a North American standard for electrical connectors for electric car, electric vehicles maintained by SAE International under the formal title "SAE Surface Vehicle Recommended Practice J1772, SAE Electric Vehicle Conductive Charge Coupler". The SAE maintains the general physical, electrical, communication protocol, and performance requirements for the electric vehicle conductive charge system and coupler. The intent is to define a common electric vehicle conductive charging system architecture including operational requirements and the functional and dimensional requirements for the vehicle inlet and mating connector. The J1772 5-pin standard supports a wide range of Single-phase electric power, single-phase (1φ) alternating current (AC) charging rates. They range from portable devices that can connect to a household NEMA 5, NEMA 5-15 outlet that can deliver 1.44 kW (12 amps @ 120 volts) to hardwired equipment that can deliver up to 19.2 kW (80 amps @ 240 volts). These connectors are sometimes informally referred to as chargers, but they are "electric vehicle supply equipment" (EVSE), since they only supply AC power to the vehicle's on-board charger, which then converts it to the direct current (DC) needed to recharge the battery. The Combined Charging System (CCS) Combo 1 connector builds on the standard, adding two additional pins for DC fast charging up to 350 kW.

History

The main stimulus for the development of SAE J1772 came from the California Air Resources Board (CARB). Early electric vehicles like the General Motors EV1 and Toyota RAV4 EV used Magne Charge (SAE J1773), an Electromagnetic induction, inductive system. CARB rejected the inductive technology in favor of conductive coupling to supply electricity for recharging. In June 2001, CARB adopted the SAE J1772-2001 standard as the charging interface for electric vehicles in California. This early version of the connector was made by Avcon and featured a rectangular connector capable of delivering up to 6.6 kW of electrical power. The California regulations mandated the usage of SAE J1772-2001 beginning with the 2006 model year. CARB would later ask for higher current delivery than the 6.6 kW that the 2001 J1772 (Avcon) standard supported. This process led to the proposal of a new round connector design by Yazaki which allowed for an increased power delivery of up to 19.2 kW delivered via single phase 120–240 V AC at up to 80 amps. In 2008, CARB published a new standard that mandated the usage of the new connector beginning with the 2010 model year; this was approved in 2012. The Yazaki plug that was built to the new SAE J1772 plug standard successfully completed certification at Underwriters Laboratories, UL. The standard specification was subsequently voted upon by the SAE committee in July 2009. On January 14, 2010, the SAE J1772 REV 2009 was adopted by the SAE Motor Vehicle Council. The companies participating in or supporting the revised 2009 standard include smart (marque), smart, Chrysler, General Motors, GM, Ford Motor Company, Ford, Toyota, Honda, Nissan Motors, Nissan, Rivian, and Tesla Motors, Tesla. The SAE J1772-2009 connector specification was subsequently added to the international IEC 62196, IEC 62196-2 standard (“Part 2: Dimensional compatibility and interchangeability requirements for a.c. pin and contact-tube accessories”) with voting on the final specification slated to close in May 2011. The SAE J1772 connector is considered a “Type 1” implementation providing a single phase coupler.“IEC International Standard for EV charging — A step forward for global EV roll-out”
, IEC Newslog, 3. February 2011

Vehicle equipment

The SAE J1772-2009 was adopted by electric vehicle manufacturers in the Chevrolet Volt and the Nissan Leaf. The connector became standard equipment in the U.S. market due to the availability of charging stations supporting it in the Electric vehicle network#United States of America, nation's electric vehicle network (helped by funding such as the ChargePoint America program drawing grants from the American Recovery and Reinvestment Act). The European versions were equipped with a SAE J1772-2009 inlet as well until the automotive industry settled on the IEC 62196, IEC Type 2 “Mennekes” connector as the standard inletsince all IEC connectors use the same #Signaling, SAE J1772 signaling protocol the car manufacturers are selling cars with either a SAE J1772-2009 inlet or an IEC Type 2 inlet depending on the regional market. There are also (passive) adapters available that can convert J1772-2009 to IEC Type 2 and vice versa. The only difference is that most European versions have an on-board charger that can take advantage of three-phase electric power with higher voltage and current limits even for the same basic electric vehicle model (such as Chevrolet Volt / Opel Ampera).

Combined Charging System (CCS)

In 2011, SAE developed a J1772/CCS ''Combo Coupler'' variant of the J1772-2009 connector in order to also support the Combined Charging System standard for direct current (DC) fast charging, which includes the standard 5-pin J1772 connector along with an additional two larger pins to support fast DC charging. ''Combo 1'' accommodates charging at 200–920 volts DC and up to 350 k

!-- needs updated with sourced specs for ''Combo 2'' connector, which can apparently handle max 350 kW charge rates --> The combination coupler will also use power-line communication technology to communicate between the vehicle, off-board charger, and smart grid. Seven car makers (Audi, BMW, Daimler, Ford, General Motors, Hyundai, Porsche, Volvo, and Volkswagen) agreed in late 2011 to introduce the Combined Charging System in mid-2012. The first vehicles using the SAE Combo plug were the BMW i3 released in late 2013, and the Chevrolet Spark EV released in 2014. In Europe, the combo coupler is based on the Type 2 (VDE) AC charging connector (Combo 2) maintaining full compatibility with the SAE specification for DC charging and the Homeplug#HomePlug Green PHY, HomePlug Green PHY PLC protocol. In 2019 Tesla introduced the Model 3 with a CCS Combo 2 plug in Europe, but has not introduced models with CCS in the US. With the introduction of the Model 3 in Europe, Tesla added CCS charging cables to V2 Superchargers (supporting both CCS Combo 2 and Tesla DC Type 2). European V3 Tesla Superchargers include only a CCS charging cable.

Properties

Connector

The J1772-2009 connector is designed for single phase alternating current electrical systems with 120 V or 240 V such as those used in North America and Japan. The round diameter connector is keyed and has five pins: The connector is designed to withstand 10,000 mating cycles (a connection and a disconnection) and exposure to the elements. With 1 mating cycle per day, the connector's lifespan should exceed 27 years.

Release mechanism

File:Charging Plug (5462096910).jpg, Black release button on a SAE J1772 plug in a mockup car File:Newone - VinFast electric charger by Phoenix Contact.jpg, SAE J1772 plugs operated by thumb at a Vietnamese Charger File:Nissan Leaf Ladekabel Mennekes.JPG, Adaptor cable from Nissan with type 1 plug for the car, type 2 plug for a European charger socket File:Type 2 connector-side oblique PNr°0525a.jpg, IEC 62196 Type 2 connector with openings on the side for automatic release The SAE J1772 or Type 1 plug is locked into the car with a hook that is manually operated, mostly by pressing a button with the thumb, which interrupts power. This allows anybody to stop charging and even theft of the cable. To prevent this, the European IEC 62196 Type 2 connector has openings on the side for automatic locking and release, operated by the car owner via remote control. If the car locks or releases its plug, the charger will follow suit according to the PP signal.

Charging

The SAE J1772-2017 standard defines four levels of charging: AC Level 1, AC Level 2, DC Level 1, and DC Level 2. Earlier released revisions of J1772 also listed a never-implemented AC Level 3, which was moved to an appendix. For example, the 2020 Chevrolet Bolt has a 66-kWh lithium-ion battery and a 7.2-kW onboard charging module (OBCM); with an EPA range of and energy efficiency of , it can use its portable charge cord to charge at AC Level 1 (120V, 12A) to get up to of range per hour or go off an AC Level 2 charging unit (240V, 32A) to get up to of range per hour. Using an optional charging station, DC fast charging (DCFC) port, this model can also charge at up to 55kW to get up to of range per half hour. Some EVs have extended J1772 to allow 120V charging at greater than 16 amps. This is useful, for example, at RV parks where NEMA connector#NEMA TT-30, TT-30 ("Travel Trailer" - 120V, 30A) receptacles are common. These allow charging at up to 24 amps. However this level of 120V charging has not been codified into J1772. Another extension, notably supported by Tesla, Inc., Tesla, is Level 2 charging at 277V. Like 208V, 277V is commonly found in North American commercial Three phase electric power, three-phase circuits.

Safety

The J1772 standard includes several levels of shock protection, ensuring the safety of charging even in wet conditions. Physically, the connection pins are isolated on the interior of the connector when mated, ensuring no physical access to those pins. When not mated, J1772 connectors have no power at the pins; they are not energized until commanded by the vehicle. The proximity detection pin is connected to a switch in the connector release button. Pressing the release button causes the vehicle to stop drawing current. As the connector is removed, the shorter control pilot pin disconnects first, causing the EVSE to drop power to the plug. This also ensures that the power pins will not be disconnected under load, causing arcs and shortening their life. The ground pin is longer than the other pins, so it breaks last.

Signaling

The signaling protocol has been designed for the following charging sequence. * supply equipment signals presence of AC input power * vehicle detects plug via proximity circuit (thus the vehicle can prevent driving away while connected) and can detect when latch is pressed in preparation for plug removal. * Control Pilot (CP) functions begin ** supply equipment detects plug-in electric vehicle (PEV) ** supply equipment indicates to PEV readiness to supply current ** PEV ventilation requirements are determined ** supply equipment current capacity provided to PEV * PEV commands energy flow * PEV and supply equipment continuously monitor continuity of safety ground * charge continues as determined by PEV * charge may be interrupted by disconnecting the plug from the vehicle The technical specification was described first in the 2001 version of SAE J1772 and subsequently the IEC 61851-1 and IEC TS 62763:2013. The charging station puts 12 V on the Control Pilot (CP) and the Proximity Pilot (AKA Plug Present: PP) measuring the voltage differences. This protocol does not require integrated circuits, which would be required for other charging protocols, making the SAE J1772 robust and operable through a temperature range of −40 °C to +85 °C.

Control Pilot

Control Pilot (Mode): The charging station sends a 1 kHz square wave on the control pilot that is connected back to the protective Earth (electricity), earth on the vehicle side by means of a resistor and a diode (voltage range ±12.0±0.4 V). The live wires of public charging stations are always dead if the CP-PE (Protective earth, Protective Earth) circuit is open, although the standard allows a charging current as in Mode 1 (maximum 16 A). If the circuit is closed, the charging station can also verify that the protective earth is functional. The vehicle can request a certain charging function by setting the resistance between the CP and PE pins; 2.7 kΩ announces a Mode 3 compatible vehicle (''vehicle detected'') which does not require charging. 880 Ω says the vehicle is ''ready'' to be charged, and 240 Ω requests ''with ventilation'' charging, in which case the charging stations supplies charging power is only if the area is ventilated (i.e., outdoors). The Control Pilot line circuitry examples in SAE J1772:2001 show that the current loop CP-PE is connected permanently on the vehicle side via a 2.74 kΩ resistor, making for a voltage drop from +12 V to +9 V when a cable is hooked up to the charging station, which activates the wave generator. The charging is activated by the vehicle by adding parallel 1.3 kΩ resistor resulting in a voltage drop to +6 V or by adding a parallel 270 Ω resistor for a required ventilation resulting in a voltage drop to +3 V. Hence the charging station can react by only checking the voltage range present on the CP-PE loop. Note that the diode will only make for a voltage drop in the positive range; any negative voltage on the CP-PE loop is blocked by D1 in the vehicle, any significant current that does flow in the CP-PE loop during the negative period will shut off the current as being considered a fatal error (like touching the pins). For IEC62196-2 male plugs the Control Pilot pin is made shorter to prevent untethered cables being used as "extension leads", This prevents the use of downstream cables that may have a lower current capability being connected to a cable of a higher current rating. Control Pilot (Current limit): The charging station can use the wave signal to describe the maximum current that is available via the charging station with the help of pulse-width modulation: a 16% PWM is a 10 A maximum, a 25% PWM is a 16 A maximum, a 50% PWM is a 32 A maximum and a 90% PWM flags a fast charge option. The PWM duty cycle of the 1 kHz CP signal indicates the maximum allowed mains current. According to the SAE it includes socket outlet, cable and vehicle inlet. In the US, the definition of the ''ampacity'' (ampere capacity, or current capacity) is split for continuous and short term operation. The SAE defines the ampacity value to be derived by a formula based on the 1 ms full cycle (of the 1 kHz signal) with the maximum continuous ampere rating being 0.6 A per 10 µs up to 850 µs (with the lowest 100 µs × 0.6 A = 6 A). Above 850 µs, the formula requires subtraction of 640 µs and multiplying the difference by 2.5. For example (960 µs − 640 µs) × 2.5 A = 80 A.

Proximity Pilot

The proximity pin, PP (also known as ''plug present''), as shown in the SAE J1772 example pinout, describes the switch, S3, as being mechanically linked to the connector latch release actuator. During charging, the EVSE side connects the PP-PE loop via S3 and a 150 Ω R6; when opening the release actuator a 330 Ω R7 is added in the PP-PE loop on the EVSE side which gives a voltage shift on the line to allow the electric vehicle to initiate a controlled shut off prior to actual disconnection of the charge power pins. However, many low-power adapter cables do not offer that locking actuator state detection on the PP pin. Under IEC 62196 the Proximity Pin is also used to indicate the cable capacity – this is relevant for non-tethered EVSEs. The resistor is coded to the maximum current capability of the cable assembly. The EVSE interrupts the current supply if the current capability of the cable is exceeded as detected by the measurement of the Rc (shown as R5 in the J1772 signaling circuit above), as defined by the values for the recommended interpretation range. Rc is placed between the PP and PE, within the detachable cable assembly.

P1901 powerline communication

In an updated standard due in 2012, SAE proposes to use power line communication, specifically IEEE 1901, between the vehicle, off-board charging station, and the smart grid, without requiring an additional pin; SAE and the IEEE Standards Association are sharing their draft standards related to the smart grid and vehicle electrification. P1901 communication is compatible with other 802.x standards via the IEEE 1905 standard, allowing arbitrary IP-based communications with the vehicle, meter or distributor, and the building where chargers are located. P1905 includes wireless communications. In at least one implementation, communication between the off-board DC EVSE and PEV occurs on the pilot wire of the SAE J1772 connector via HomePlug Green PHY power line communication (PLC).

Competing standards

A competing proposal known as the Mennekes connector initiated by RWE and Daimler was standardized in 2011's IEC 62196 as its Type 2 connector. It has been widely adopted as the European Union's standard single and three phase coupler. The connector adopted the same protocols for the pilot pin as J1772's J-Plug. The IEC specification allows for up to 63 A and 43.6 kW. In 2018, the SAE J3068 committee released an enhancement to the EU connector tailored for the North American industrial market allowing up to 160 A / 166 kW on 3φ power. The same IEC 62196-2 standard also specified a pair of Type 3 connector from Scame Global providing a single and three phase coupler with shutters. After a 2016 approval by the IEC for a small modification to the Mennekes connector optionally allowing shutters, Type 3 has been deprecated. Tokyo Electric Power Company has developed a specification solely for automotive high-voltage DC fast charging using the JARI DC connector, and formed the CHAdeMO (''charge de move'', equivalent to "charge for moving") association with Japanese automakers Mitsubishi Motors, Mitsubishi, Nissan and Subaru to promote it.

References

External links

SAE J1772 Committee
{{DEFAULTSORT:Sae J1772 Charging stations International Electrotechnical Commission Mains power connectors Plug-in hybrid vehicle industry Automotive standards