Jerry Palmer is a retired automotive designer.

Career

Palmer graduated from the

College for Creative Studies College for Creative Studies (CCS) is a private art school in Detroit, Michigan. It enrolls more than 1,400 students and focuses on arts education. The college is also active in offering art education to children through its Community Arts Par ...

in 1966, and immediately started working for General Motors' design studios. He was appointed chief designer at

Chevrolet Chevrolet ( ), colloquially referred to as Chevy and formally the Chevrolet Motor Division of General Motors Company, is an American automobile division of the American manufacturer General Motors (GM). Louis Chevrolet (1878–1941) and ous ...

III Studio in 1974, later being promoted to GM's Advance Design division in 1986, director of the

Thousand Oaks Thousand Oaks is the second-largest city in Ventura County, California, United States. It is in the northwestern part of Greater Los Angeles, approximately from the city of Los Angeles and from Downtown. It is named after the many oak tree ...

Advance Concept Centre in 1990, and finally executive director of design. "Palmer retired in 2002 as the executive director of design for General Motors (GM) North American Operations. In this position, he oversaw the interior and exterior design of all of GM’s production vehicles." He was a principal designer."Palmer was largely responsible for the design of the four rotor-Aerovette" which was "his design of the Fourth Generation Corvette". He "began working on the design and advanced aerodynamics that became the 1984 Corvette." "Jerry Palmer was the chief stylist for the third-generation Camaro." In 2000, he was inducted into the Corvette Hall of Fame.

Designs

* 1978

Chevrolet Camaro Z28 The Chevrolet Camaro is a mid-size American automobile manufactured by Chevrolet, classified as a pony car. It first went on sale on September 29, 1966, for the 1967 model year and was designed to compete with the Ford Mustang. The Camaro sh ...

facelift * 1978

Chevrolet Corvette (C3) The Chevrolet Corvette (C3) is a sports car that was produced from 1967 until 1982 by Chevrolet for the 1968 to 1982 model years. Engines and chassis components were mostly carried over from the previous generation, but the body and interior we ...

facelift A facelift, technically known as a rhytidectomy (from the Ancient Greek () "wrinkle", and () "excision", the surgical removal of wrinkles), is a type of cosmetic surgery procedure used to give a more youthful facial appearance. There are mul ...

* 1980

* 1982

Chevrolet Camaro The Chevrolet Camaro is a mid-size American automobile manufactured by Chevrolet, classified as a pony car. It first went on sale on September 29, 1966, for the 1967 model year and was designed to compete with the Ford Mustang. The Camaro ...

Pontiac Firebird The Pontiac Firebird is an American automobile that was built and produced by Pontiac from the 1967 to 2002 model years. Designed as a pony car to compete with the Ford Mustang, it was introduced on February 23, 1967, five months after GM's ...

* 1984

Chevrolet Corvette (C4) The Chevrolet Corvette (C4) is a sports car produced by American automobile manufacturer Chevrolet from 1983 until 1996. The convertible returned, as did higher performance engines, exemplified by the LT5 found in the ZR-1. In early March 1990 ...

* 1987

Chevrolet Beretta The Chevrolet Beretta is a front-wheel-drive two-door coupé produced by Chevrolet from 1987 until 1996. The Beretta was designed in the same design studio as the Camaro and the Corvette, Chevrolet Exterior Studio 3, and was built at the Wilmi ...

* 1990 CERV III

References

{{DEFAULTSORT:Palmer, Jerry American automobile designers General Motors designers General Motors people