![Janka hardness test](https://upload.wikimedia.org/wikipedia/commons/7/76/Janka_hardness_test.jpg)
The Janka hardness test (; ), created by Austrian-born American researcher Gabriel Janka (1864–1932), measures the resistance of a sample of wood to denting and wear. It measures the
force required to embed an steel ball halfway into a sample of wood. (The diameter was chosen to produce a circle with an area of 100 square millimeters
ne square centimeter
NE, Ne or ne may refer to:
Arts and entertainment
* Neutral Evil, an alignment in the American role-playing game ''Dungeons & Dragons''
* New Edition, an American vocal group
* Nicomachean Ethics, a collection of ten books by Greek philosopher A ...
) A common use of Janka hardness ratings is to determine whether a species is suitable for use as
flooring
Flooring is the general term for a permanent covering of a floor, or for the work of installing such a floor covering. Floor covering is a term to generically describe any finish material applied over a floor structure to provide a walking surface ...
. For hardwood flooring, the test usually requires a sample with a thickness of at least 6–8 mm, and the most commonly used test is the ASTM D1037. When testing wood in lumber form, the Janka test is always carried out on wood from the tree trunk (known as the heartwood), and the standard sample (according to ASTM D143) is at 12% moisture content and clear of knots.
The hardness of wood varies with the direction of the
wood grain
Wood grain is the longitudinal arrangement of wood fibers or the pattern resulting from such an arrangement.
Definition and meanings
R. Bruce Hoadley wrote that ''grain'' is a "confusingly versatile term" with numerous different uses, including ...
. Testing on the surface of a plank, perpendicular to the grain, is said to be of "side hardness". Testing the cut surface of a stump is called a test of "end hardness". Side hardness may be further divided into "radial hardness" and "tangential hardness", although the differences are minor and often neglected.
The results are stated in various ways, leading to confusion, especially when the actual units employed are often not attached. The resulting measure is always one of
force
In physics, a force is an influence that can change the motion of an object. A force can cause an object with mass to change its velocity (e.g. moving from a state of rest), i.e., to accelerate. Force can also be described intuitively as a p ...
. In the United States, the measurement is in
pounds-force
The pound of force or pound-force (symbol: lbf, sometimes lbf,) is a unit of force used in some systems of measurement, including English Engineering units and the foot–pound–second system.
Pound-force should not be confused with pound-ma ...
(lbf). In Sweden it is in
kilograms-force
The kilogram-force (kgf or kgF), or kilopond (kp, from la, pondus, lit=weight), is a non-standard gravitational metric unit of force. It does not comply with the International System of Units (SI) and is deprecated for most uses. The kilogram- ...
(kgf), and in Australia, either in
newton
Newton most commonly refers to:
* Isaac Newton (1642–1726/1727), English scientist
* Newton (unit), SI unit of force named after Isaac Newton
Newton may also refer to:
Arts and entertainment
* ''Newton'' (film), a 2017 Indian film
* Newton ( ...
s (N) or kilonewtons (kN). This confusion is greatest when the results are treated as units, for example "660 Janka".
The Janka hardness test results tabulated below followed
ASTM
ASTM International, formerly known as American Society for Testing and Materials, is an international standards organization that develops and publishes voluntary consensus technical standards for a wide range of materials, products, systems, an ...
D 1037-12 testing methods. Lumber stocks tested range from 1" to 2" thick. The tabulated Janka hardness numbers are an average. There is a standard deviation associated with each species, but these values are not given. No testing was done on actual flooring. Other factors affect how flooring performs: the type of core for engineered floorings, such as pine, HDF, poplar, oak, or birch; grain direction and thickness; floor or top wear surface, etc. The chart is not to be considered an absolute; it is meant to help people understand which woods are harder than others.
Typical Janka hardness values
References
External links
Janka Hardness Scale For Wood – Side Hardness Chart of Some WoodsUSDA – Wood Handbook – Wood as an Engineering MaterialUSDA – Janka Hardness Using Nonstandard Specimens
{{DEFAULTSORT:Janka Hardness Test
Woodworking
Woodcarving
Wood
Hardness tests