Trailer connectors between the trailer and passenger car, light truck or heavy trucks with 12V systems
In Europe, both 7-pin (ISO 1724) and 13-pin (ISO 11446) are common. The 13-pin version being phased in is newer, provides more services than the 7-pin, a more positive locking and also better protection against moisture and contamination. The connectors are designed for 12V systems. Exceptions for the 7-pin connector may exist where they may be used for 6V and 24V. Vehicles and trailers with 6V systems can use the 7-pin or a 5-pin connector, but these are rare today. Heavy trucks that may have 12V systems are usually older (vintage vehicles) or on non-European markets. The color coding is defined in ISO 4141-3, but the standard color codes are not always followed and may be different for a particular vehicle.13-pin trailer connector ( ISO 11446)
Physical design of the standard ISO 11446 but also called Jaeger-connector from the company that developed it. The following supplementary information exists for the connector:7-pin trailer connector for ABS/ EBS (ISO 7638-2)
Physical design according to standard ISO 7638-2. This connector is intended to be used for 12V ABS and EBS on heavy duty trailers. Identified by key tab on outer ring between pin 3 and 4. The following supplementary information exists for the connector:7-pin trailer connector Type 12N (ISO 1724)
Physical design according to standard ISO 1724. The 7-pin connector uses on newer trailers all 7 pins according to the ISO standard. On older trailers there's sometimes a 5-wire setup using a 7-pin connector. In these cases exclude connection for right tail light (58R) and rear fog light (54G) and connect the tail lights only to pin for left tail light (58L). Joining the pins for right and left tail lights (58R and 58L) can cause problems on German cars where it is possible to activate Standing Lamps on only one side of the vehicle.Pin 2 (54G)
According toSpecial case for Australia
Australia uses basically the same wiring with the exception for pin 5 and pin 2. The problematic part here is that pin 5 is used for trailer brake which means that if you for some reason connect an Australian trailer to a towing vehicle with ISO wiring you will get into trouble with the trailer brakes being applied as soon as you turn on the lights. Further reading at Trailer Connector/Australia.7-pin trailer connector Type 12S (ISO 3732)
Physical design according to standard ISO 3732. Signals in this connector (if following the standard) are not generally legally required (local regulations may still apply), which means that it is not mandatory to connect it if it is present. This connector is basically the same as the 12N (ISO 1724) connector, but the center pin (pin 7) has changed gender to make the plug and outlet unique. Socket is replaced with pin in the plug, pin is replaced with socket in outlet. The purpose of this connector is to supplement the 12N (ISO 1724) connector for power supply of consumers common in caravans (Travel trailers). This is used in5-pin connector (ISO 1724)
Physical design according to standard ISO 1724. The 5-pin has a design and pin layout that is identical to the 7-pin ISO 1724 connector with the exception for the lack of pin 1 (L) and pin 4 (R). This connector is sometimes present on vintage vehicles and the actual wiring may be completely different from what the standard states which means that measuring before connecting is a good idea. Whenever there is a need to change the plug or outlet it can be replaced with a 7-pin.Trailer connectors between heavy duty trailer and the tractor unit
These connectors are designated as 24 volt.15-pin trailer connector (ISO 12098)
Physical design according to standard ISO 12098. This connector is present on newer heavy duty commercial trucks and trailers following the ISO standard and is intended to replace the combination of connectors according to standards ISO 1185 and ISO 3731. The 15-pin connector is not designed to replace the ISO 7638 connector. The following supplementary information exists for the connector:7-pin trailer connector for ABS/ EBS (ISO 7638-1)
Physical design according to standard ISO 7638-1. This connector is intended for 24V ABS and EBS on heavy duty trailers. Identified by key tab on outer ring by pin 5. The following supplementary information exists for the connector:7-pin trailer connector 24N (ISO 1185)
Physical design according to standard ISO 1185. This connector is common on heavy duty commercial trucks and trailers but is replaced by the ISO 12098 connector on newer vehicles. The following supplementary information exists for the connector:7-pin trailer connector 24S (ISO 3731)
Physical design according to standard ISO 3731. This connector is common but on newer vehicles it is replaced by the connectors according to ISO 12098 and ISO 7638.See also
*References
Symbol Guide
{{DEFAULTSORT:Trailer Connector ISO Automotive electrics Trailers DC power connectors