History of the IEC standard
The International Electrotechnical Commission (IEC) was established inHistory of the ANSI standard
Standardization of batteries in theIEC battery nomenclature
Three different technical committees of IEC make standards on batteries: TC21( lead-acid), SC21(other secondary) and TC35( primary). Each group has published standards relating to the nomenclature of batteries - IEC 60095 for lead-acid starter batteries, IEC 61951-1 and 61951-2 for Ni-Cd and Ni-MH batteries, IEC 61960 for Li-ion, and IEC 60086-1 for primary batteries.Primary batteries
Battery numbering
Examples of the IEC nomenclature are batteries coded R20, 4R25X, 4LR25-2, 6F22, 6P222/162, CR17345 and LR2616J. The letters and numbers in the code indicate the number of cells, cell chemistry, shape, dimensions, the number of parallel paths in the assembled battery and any modifying letters deemed necessary. A multi-section battery (two or moreElectrochemical system
The first letter identifies the chemical composition of the battery, which also implies a nominal voltage. It is common to refer to the negative electrode first in IEC battery definitions. ''Italics'' indicate a chemical system unlikely to be found in consumer or general-purpose batteries, or withdrawn from the current standard.Shape
Shape codes are: : R Round, (coin, button or cylindrical) : P Not round : ''F Flat (layer built)'' : ''S Square (or rectangular or prismatic)'' The ''F'' and ''S'' shape codes are still in use but are not to be used for new battery definitions.Size code
Certain sizes, given by one or two digit numbers, represent standard size codes from previous editions of the standard. Sizes given as 4 or more digits indicate the diameter of the battery and the overall height. The numbers in the code correlate with the battery dimensions. For batteries with dimensions of < 100 mm the (truncated) diameter in millimetres, followed by the height in tenths of a millimetre; for batteries with a single dimension ≥ 100 mm the diameter in millimetres, then a slash (/) followed by the height in millimetres. As well as the recommended size code definitions there are also ten modifying suffix letters that can be added to the end of the specific size code. These run from A to L (omitting F and I) and depending on the largest dimension of the battery can either signify 0.0 – 0.9 mm maximum dimensions or 0.00 – 0.09 mm maximum dimensions with A being 0.0 or 0.00 and L being 0.9 or 0.09. For flat cells the diameter code is given as the diameter of a circle circumscribed around the whole cell's area. Standardized size codes for round batteries which do not follow the current nomenclature but have been retained for ease of use are given by a one or two digit number following the R. These include but are not limited to: Round button batteries also carry two-digit size codes such as R44, see the button battery table for typical dimensions. Other round, flat, and square sizes have been standardized but are used mostly for components of multi-cell batteries. The following is a partial list of IEC standard recommended diameter and height codes for round cells:Modifiers
After the package size code(s), additional letters may optionally appear. Terminal styles and variants of the same battery can be designated with the letters X or Y. Performance levels may also be designated with a C, P, S, CF, HH, or HB or other letter suffixes. An appended letter "W" states that this battery complies with all the requirements of the IEC 60086-3 standard for watch batteries, such as dimensional tolerance, chemical leakage, and test methods.Battery categories
IEC nomenclature classifies batteries according to their general shape and overall physical appearance. These categories, however, are not identified in the IEC battery nomenclature: * Category 1: Cylindrical cells with protruding positive and recessed or flat negative terminals. The positive terminal shall be concentric with the cell overall. The total height of the cell is not necessarily the same as the total distance between terminals (This accounts for nubs, recesses and battery casings). The cell casing is insulated. ''E.g. R1 & LR8D425'' * Category 2: Cylindrical cells with protruding positive and protruding or flat negative terminals. The total height of the cell is the same as the total distance between terminals. The cell casing is insulated. ''E.g. CR14250, LR61'' * Category 3: Cylindrical cells with flat positive and negative terminals. The total height of the cell is not necessarily the same as the total distance between terminals (This accounts for any protuberances from the negative terminal). The cell casing is in connection with the positive terminal. No part of the cell is allowed to protrude from the positive terminal surface. ''E.g. CR11108, LR9'' * Category 4: Cylindrical cells with a protruding flat negative terminal. The total height of the cell is the same as the total distance between terminals. The cell casing is the positive terminal and it is recommended that the outer surface is used for positive connection even though it is possible from the base. No part of the cell is allowed to protrude from the positive terminal surface. ''E.g. LR44, CR2032'' * Category 5: Cylindrical batteries which fit none of the other categories. ''E.g. R40, 8LR23'' * Category 6: Non-cylindrical batteries. ''E.g. 3R12, 4R25, 6F22''Secondary batteries
Nickel-cadmium and nickel-metal hydride batteries
Nickel-cadmium and Nickel-metal hydride batteries follow a similar rule as the system above; especially cylindrical cells designed to be dimensionally interchangeable with primary batteries use the same designation as the primary batteries, the codes for electrochemical systems as below. All other cells use the following system: * Small prismatic cells: KF or HF followed by maximum width in mm / maximum thickness in mm / maximum height in mm. E.g. KF 18/07/49 * Cylindrical cells: KR or HR followed by a letter indicating discharge rate (L, M, H or X for low, medium, high and very high, respectively); then another letter may be added to indicate use at elevated temperatures (T or U) or rapid charge (R); then maximum diameter in mm / maximum height in mm. E.g. KRL 33/62, HRHR 23/43 * Button cells: KB or HB followed by maximum diameter in tenths of mm / maximum height in tenths of mm. E.g. KBL 116/055Lithium-ion batteries
Lithium-ion batteries have a different rule for naming, which applies both to batteries of multiple cells and single cell. They will be designated as:IEC 61960 ed1.0 N1A1A2A3N2/N3/N4-N5 where N1 denotes number of series connected cells and N5 denotes number of parallel connected cells (only when the number is greater than 1); these numbers only apply to batteries. A1 indicates the basis of negative electrode phase, where I is for lithium ion and L is for lithium metal or alloy. A2 indicates the basis of positive electrode phase, and could be C, N, M, V or T for cobalt, nickel, manganese, vanadium and titanium respectively. A3 is for the shape of the cell; either R for cylinder or P for prism. N2 is the maximum diameter (in case of cylindrical cells) or thickness (prismatic cells) in mm. N3 is only used for prismatic cells to denote the maximum width in mm. N4 is the maximum overall height in mm. (For any of the lengths above, if the dimension is smaller than 1 mm it can be written as tN, where N is tenths of mm) E.g. ICR19/66, ICP9/35/48, 2ICP20/34/70, 1ICP20/68/70-2ANSI battery nomenclature
Early editions of the ANSI standard used a letter code to identify the dimensions of the cell. Since at the time there were only carbon-zinc cells, no suffix letters or other notation were required. The letter system was introduced in the 1924 edition of the standard, with letters A through J assigned approximately in order of increasing cell volume, for cells typically manufactured at that time. By 1934, the system had been revised and extended to 17 sizes ranging from NS at inch diameter by inch height, through size J at inches diameter by inches high, to the largest standard cell which retained its old designation of No. 6 and which was inches in diameter and 6 inches high.Size and shape codes
The current edition of the standard uses a numerical code to show the cell size. Common round cell sizes are: Since these IEC and ANSI battery standards have been harmonized, for example, an R20 cell will have the same dimensions as an ANSI 13 cell. Flat cells, used as components of multi-cell batteries, have an F prefix and a series of numbers to identify sizes. Coin cells were assigned size codes in the 5000 range. Secondary cells using systems H and K (nickel-metal hydride and nickel-iron sulfide) have a separate series of size codes, but the cells are dimensionally interchangeable with primary cells.System and performance suffix letters
The electrochemical system and performance information is given in suffix letters.See also
*References
{{List of IEC standards Battery (electricity) Technical terminology