General principles
Diving equipment is used to facilitate underwater activity by the diver. The primary requirements are to keep the diver alive and healthy during the dive. Secondary requirements include providing diver comfort, and sufficient capacity to perform the intended activities. The diver is an integral part of the system, which relies on diver competence as well as correct equipment function for safe operation. Fault tolerance is the property that enables a system to continue operating properly in the event of the failure of some of its components. If its operating quality decreases at all, the decrease is proportional to the severity of the failure, as compared to a naively designed system, in which even a small failure can cause total breakdown. Fault tolerance is particularly important in high availability orBreathing apparatus
Breathing apparatus must allow the diver to breathe with minimum added work of breathing, and minimise additionalRebreathers
Rebreather equipment removes carbon dioxide from exhaled gas and replaces the oxygen, then lets the diver breathe the gas again. This can be done in a self-contained system carried by the diver, in a system where the scrubber is carried by the diver and gas is supplied from the surface, or where the gas is returned to the surface for recycling, and the power to circulate gas in the loop can be the lung power of the diver, energy from the supply gas pressure, or externally powered booster pumps. Scuba rebreathers tend to circulate the gas in the breathing loop by lung power, and the work of breathing can be a significant part of diver effort at depth, in extreme circumstances it may exceed the capacity of the diver. The widest variety of rebreather types is used in diving, as the physical and physiological consequences of breathing under pressure complicate the requirements, and a large range of engineering options are available depending on the specific application and available budget. A diving rebreather is safety-critical life-support equipment – some modes of failure can kill the diver without warning, others can require immediate appropriate response for survival. General operational requirements include: *waterproof and corrosion resistant construction *reasonably close to neutrally buoyant and balanced after ballasting *acceptably streamlined, to minimize added swimming resistance *low work of breathing in all diver attitudes and over the full operating depth range *the unit should not adversely affect the diver's trim and balance *easy and quick release of harness and unaided removal of the unit from the diver *accessibility of control and adjustment components *unambiguous feedback to the diver of critical information *no critical single-point failure modes – The user should be able to deal with any single reasonably foreseeable failure without outside help Special applications may also require: *low noise signal *low emission of bubbles/small bubbles *low electromagnetic signature *rugged construction *light weight in air *minimal additional task-loading for normal operation Rebreathers can vary considerably in setup and operation, and type training is considered essential for safe operation by the training agencies and manufacturers.Diving suits
Diving suits are worn for protection from the environment. In most cases this is to keep the diver warm, as heat loss to water is rapid. There is a trade-off between insulation, comfort, and mobility. When diving in the presence of hazardous materials, the diving suit also serves as personal protective equipment to limit exposure to those materials.Wetsuits
Wetsuits rely on a good fit to work effectively. The insulation relies on the low heat conductivity of the gas bubbles in the neoprene foam of the suit slowing heat loss from the water inside the suit to the water outside. If the water inside the suit can be flushed out and replaced by cold water, this insulating function is bypassed. Movement of the diver tends to move the water in the suit around mostly where it is present in thick layers, and if this water is forced out it will be replaced by cold water from outside. A close fit reduces the thickness of the layer of water and makes it more resistant to flushing. Semi-dry suits attempt to address this issue by making it more difficult for water to enter and leave the suit. They are also most effective when close fitting. A different problem can be caused by a suit that is too tight. If it restricts breathing this can aggravate work of breathing issues due to depth and gas density, which may not be noticeable at the surface, but can become a serious problem at depth. The insulation of foamed neoprene is mostly in the gas bubbles, which are compressed by the ambient pressure, so the insulation reduces with depth. Heavier duty neoprene compresses less but is less flexible, so it may be a better insulator, but may also encumber the diver more. A number of inner surface finishes, from bare rubber to plush have been tried. Each has advantages some of the time. Wetsuits are sufficiently similar that once the buoyancy characteristics of a different suit have been compensated by correct ballasting and a suitable buoyancy compensator selected, very little familiarisation is needed, and retraining is unnecessary.Dry suits
Dry suits rely on staying dry inside and maintaining a limited volume of gas distributed through the thermal undergarments. The volume of gas needed is fairly constant, but it expands and contracts in response to the ambient pressure variations as the diver changes depth. Squeeze and overinflation are dangerous. Suit squeeze is caused by insufficient gas in the suit, and will reduce flexibility of the suit and restrict the diver's freedom of motion. This could prevent the diver from reaching critical equipment in an emergency. Gas is added manually by pressing a button to open the inflation valve, which is customarily sited in the central chest area where it can easily be reached by both hands and is clear of the harness and buoyancy compensator. High flow rates are neither necessary nor desirable, as they could lead to overinflation, particularly if the valve sticks open due to freeze. Overinflation will cause an uncontrollable rapid ascent if not corrected. Dumping of suit gas is only possible in a restricted range of orientations, where the dump valve is above the gas to be dumped. During ascent, the diver has several things to monitor and do. so an adjustable automatic exhaust valve which provides hands-free operation helps reduce this task loading. Problems caused by flooding of dry suits: *Loss of thermal insulation and body chilling will generally make it necessary to abort the dive, but an immediate ascent may not be possible, or safe. *Loss of buoyancy can be mitigated by deploying a DSMB, use of a large volume buoyancy compensator, or small lifting bag, or ditching ballast weight. It depends on details of the leak whether the suit will retain any gas, and where such gas can be held. *The added mass and bulk of water in the suit will make exit from the water difficult. Mitigation is possible by fitting ankle dumps or cutting the suit at each ankle to allow the water to drain. The ability of the diver to reach the cylinder valve can be constrained by the suit and personal joint flexibility of the diver. Back-mount configurations with valves up are difficult for many divers to reach to open or close the valves. This can cause delays in reacting effectively to some emergencies. This is partly a suit issue and partly a cylinder configuration issue. The combination of suit and helmet can constrain movement more than either on its own. Dive suits can produce physiological strain in the user and considerable effort may be necessary to overcome the encumbrance of the suit. This can result in longer periods required to complete complex tasks, in an environment that is already non-conducive to dexterity or heavy labour. This was particularly noticeable on the standard diving suit. Wrist and neck seals are commonly available in latex rubber, silicone rubber and expanded neoprene. Some divers are allergic to latex, and should avoid latex seals. Dry suits can be effective for protection against exposure to a wide range of hazardous materials, and the choice of suit material should take into account its resistance to the known contaminants.Hot water suits
Hot water suits are usually made in one piece of foamedAtmospheric suits
The physiological problems of ambient pressure diving are largely eliminated by isolating the diver from the water and hydrostatic pressure in an atmospheric suit. Dexterity problems with manipulators on atmospheric diving suits reduce their effectiveness for many tasks. The joints of atmospheric suits allow walking but are not suitable for swimming. The interior of the suit must maintain constant volume during articulation, as a variable volume would require additional effort to move from a lower volume geometry to higher volume due to the large pressure difference. A range of user sizes can be accommodated by providing spacers between components, but the extra joints are potential leaks. Mix and match alternative limbs that require moving seals to be split and reconnected may need to be pressure tested before use. The work required to overcome friction in the pressure-resistant joint seals, inertia of the limb armour, and hydrodynamic drag of the bulky limbs moving through the water are major constraints on agility and the modes of locomotion available, though buoyancy control is relatively simple, as the suit is relatively incompressible, and the life support system is closed so there is no weight change due to gas consumption. Although the pressure hull of the suit is often made from metals with high heat conductivity, insulating the diver is largely a matter of wearing clothing suitable for the internal air temperature, and insulating the shell away from the moving parts of joints is fairly straightforward. The air is recycled through the scrubber, which will heat it slightly through the exothermic chemical reaction which removes carbon dioxide. The helmet is rigidly connected to the torso of the suit, which limits the field of vision. this can be partly compensated by using a nearly hemispherical dome viewport. Atmospheric diving suits are still an emerging technology, and differ considerably, so specialist training is required for each model.Harness
The surface-supplied diver's harness is an item of strong webbing, and sometimes cloth, which is fastened around a diver over the exposure suit, and allows the diver to be lifted without risk of falling out of the harness. It also provides support for the bailout gas cylinder, and may carry the ballast weights, a buoyancy compensator, the cutting tool, and other equipment. Several types are in use. Recreational scuba harness is mainly used to support the gas cylinders, buoyancy compensator and often the weights and small accessories, but is not normally required to function as a lifting harness. These functions require distribution of the loads to the diver securely and comfortably. Load distribution of weight carried by the harness can cause discomfort and nerve pressure injury out of the water, and the weight of the harness including cylinders can be problematic for putting the set on for some divers. A harness that must support side-mounted cylinders should not unduly encumber the diver or make it difficult to access critical equipment like buckles, weights, cylinder valves, demand valves and pressure gauges. More than one cylinder may be mounted at each side. In professional diving the harness must also function as a lifting harness, and must be strong enough to support the diver and attached equipment if lifted by the lifeline or umbilical, without causing direct or indirect injury. Some discomfort is considered acceptable as this is an emergency procedure.Buoyancy control equipment
Buoyancy control by adjustable volume of gas in an environment where pressure varies rapidly with depth is inherently unstable and requires continuous monitoring and control input from the diver. The instability is proportional to the volume of the gas required for neutral buoyancy. For the least sensitivity to depth variation, the volume of gas required for neutral buoyancy should be kept to a minimum averaged over the dive. This implies ballasting that is just sufficient to allow neutral buoyancy at the minimum weight of diver and equipment that is reasonably likely to occur during the dive. The obvious case is where a delay pushes the diver further into decompression obligation than planned, and it may be necessary to decompress at a shallow stop with the last remaining gas. This is not a time to be struggling to stay down, using more gas than otherwise necessary with the effort. The weight change in most dives is due to gas use, and unless equipment is lost or abandoned, the maximum weight change is the consumption of all the gas in all the cylinders carried. This can be calculated easily. The diver needs enough buoyancy volume to remain comfortably afloat before the dive starts. At the end of the dive there will be more buoyancy in reserve as a result of the gas consumption. Any large amount of reserve volume in the buoyancy compensator has potential for contributing to an uncontrolled buoyant ascent. Gas in the dry suit is primarily intended for thermal insulation. The additional buoyancy is a normally undesirable but unavoidable side effect. When there is sufficient gas to relieve compression of the under-suit, any excess will gather at a local high point and contributes little to insulation. Removal of excess gas from the suit is only possible when the path of the excess gas to the dump valve or other vent point is upward. Automatic dump valve position is conventionally on the upper left sleeve, clear of the harness, but in easy reach of the diver at all times and at a natural high point for the most useful and likely trim positions for swimming, work, and particularly ascents. Other less popular options are on the forearm or cuff dumps, and most cuff seals will vent if raised high enough unless dry gloves are worn. Any upward excursion by the diver will cause the gas in the suit to expand in proportion to the pressure change. Diver trim which guarantees easy venting of the suit during a normal, head-up ascent is inefficient for horizontal propulsion. The diver in a position trimmed with feet high is at risk of losing control of buoyancy in the event of a significant upward excursion. This can be mitigated by ankle dump valves, but they are not fitted as standard equipment and are not used by most divers. Finning downwards against the buoyancy of excess gas trapped in the legs of a dry suit is energetic at best and futile at worst. The problem can be exacerbated if the legs are baggy at the ankles and the boots are loose, as if they slip off the feet all control of, and transfer of power to the fins is lost. Gaiters and ankle straps can reduce the volume of this part of a suit, and may also reduce hydrodynamic drag, while ankle weights require acceleration with every fin stroke. The dry suit should not unduly restrict the diver's freedom of movement, but should not be excessively baggy, which can trap gas in unwanted places, and can increase drag as well as causing buoyancy and trim problems. The inherently baggy rubberised canvas standard diving dress was available with lace-up legs to manage this problem. This option is no longer available, and divers must have suits tailored for a good fit. Female divers are reported to have more difficulties with buoyancy and trim. This may be a consequence of a buoyancy distribution not well catered for by most harness, buoyancy compensator and weighting systems, possibly exacerbated by dry suit buoyancy distribution. Many manage with available equipment, but it may take longer to learn to use less ergonomically matched equipment effectively. A similar problem is reported with unusually small divers. The operating skills for most types of single bladder buoyancy compensator are standardised and portable between models. Familiarisation is rapid and straightforward, and retraining is generally not required, though additional training is provided for adapting to sidemount because of the associated changes in breathing apparatus management. Twin bladder units require more adaptation of procedures, and are associated with more accidents due to human error, as there are more kinds of operator errors that can be made.Weights
Weighting systems are needed to compensate for the buoyancy of the diver and buoyant equipment, mainly thermally insulating diving suits. The distribution of buoyancy and ballast affect diver trim, which influences propulsion efficiency, and through that, breathing gas consumption. Weight-belts of conventional design are fastened around the waist and load the lower back when the diver is trimmed horizontal. This can cause lower back pain, particularly when heavy to compensate for the buoyancy of a dry suit with thick undergarments. Weights supported by the harness distribute the load more evenly. Ankle weights used to improve trim add inertia to the feet, which must be accelerated and decelerated with every fin stroke, requiring additional power input for finning and reducing propulsive efficiency. The facility to shed ballast weight is considered a safety feature for scuba diving as it allows the diver to achieve a positive buoyancy in an emergency, but inadvertent loss of ballast when the diver needs to control ascent rate is itself an emergency that can cause decompression illness. The need to pull weights clear of other equipment when ditching in some orientations is additional task loading in an emergency. Getting the weight belt caught up in the harness can compound the diver's problems if the need to establish positive buoyancy is urgent. Ditching all weights may be appropriate for some emergencies, but in others it just changes the nature of the emergency.Fins
Fin design is a compromise between propulsive efficiency and maneuverability. Monofins are the equipment of choice for deep apnea diving and both speed and endurance competition. Breath hold spearfishers need more maneuverability while retaining the best reasonably practicable efficiency, and they mostly choose long bifins. Professional and recreational scuba and surface-supplied divers will sacrifice more efficiency for better maneuverability. Comfort issues, stressing of muscles and joints, particularly with less physically fit divers, may bias the choice towards softer fins that produce less thrust and maneuverability. Divers needing maximum maneuverability will usually choose stiff paddle fins which can be effective for reversing out of a tight spot but are inefficient for cruising using flutter kick. These fins work well with the frog kick, which is also less likely to shed vortices downward and disturb silty bottoms, so this style of fin is popular for cave and wreck penetration diving. Experimental work suggests that larger fin blades are more efficient in converting diver effort to thrust, and are more economical in breathing gas for similar propulsive effect. Larger fins were perceived to be less fatiguing than smaller fins. For each kick stroke the mass of the fin must be accelerated once in each direction, so getting more thrust per stroke will waste less work on fin and leg accelerations. This effect also relates to heavier fins, boots and ankle weights. Attachment to the foot follows two basic options. An integral foot pocket enclosing the heel, or an open heeled foot pocket with an elastic heel strap, which may be of adjustable length. Both systems allow full mobility of the ankle joint for bi-fins, but limit the motion for monofins. Full foot-pockets are softer and more comfortable on bare feet, and spread the loads more evenly, but are often unsuited to wearing over a thick or hard-soled boot suitable for crossing rough rocky shores. Fin retainers may be necessary for security if the fit is a bit loose. Open heel foot pockets can be matched with foot width when wearing a boot, and the heel-strap selected or adjusted to fit. Fin straps may be of fixed or adjustable length. Fixed length straps are always the right length for a single user, and have fewer snag points, moving parts and other things that can fail. Adjustable straps are quickly adaptable to the feet of different users, a major advantage for rental equipment.Masks and helmets
Diving masks and helmets have some common functions: both provide an air space between the eyes a and a transparent window to allow the diver a clear view underwater. Other functions may differ or partly overlap.Seal
The mask must form a watertight seal around the edges to keep water out of the mask, regardless of the attitude of the diver in the water. This seal is between the elastomer skirt of the mask and the skin of the face. Fit of mask affects the seal and comfort and must account for variability of face shapes and sizes. This is achieved for half masks by the very wide range of models available, but in spite of this some faces are too narrow, or noses too large to fit comfortably. This is less of a problem with full-face masks and less again with helmets, but other problems affect these, like overall head size, and neck length and circumference, so there is still a need for adjustment and a few size options. Face and neck seals may be compromised by hair passing under the seal between the rubber and skin, and the amount of leakage will depend on the amount of hair and the position of the compromised part of the seal. Divers with large amounts of facial hair can usually compensate adequately on open circuit, but may use more gas than otherwise necessary with a rebreather due to leakage and more frequent need to clear water from the mask.Equalising
Two aspects of equalising the pressure in gas spaces are influenced by mask and helmet design. These are equalising the internal space of the mask or helmet itself, and equalising the ears. Equalising the internal space of a half mask is normally achieved through the nose, and equalising the ears requires a method to block the nostrils. This is relatively easy to do with half-masks, where the diver can usually pinch the nostrils closed through the rubber of the mask skirt. Helmets and most full-face masks do not allow the diver finger access to the nose, and various mechanical aids have been tried with varying levels of comfort and convenience.Vision
The field of vision of the diver is reduced by opaque parts of the helmet or mask. Peripheral vision is particularly reduced in the lower areas due to the bulk of the demand valve. Helmet design is a compromise between low mass and inertia, with relatively small interior volume and viewports affording restricted field of vision, and large viewports with large interior volume. Siting the viewport close to the eyes helps provide a better view but is complicated by the need for sufficient clearance in front of the nose for a wide range of divers. Curved viewports can introduce visual distortions that can reduce the effectiveness of the diver at judging distance, and almost all viewports are made flat. Even a flat viewport causes some distortion, but it takes relatively little time to get used to this, as it is always the same. Spherical port surfaces are generally used in recent atmospheric suits for structural reasons, and work well when the interior volume is large enough. They can be made wide enough for adequate peripheral vision. Field of vision in helmets is affected by mobility of the helmet. A helmet directly supported by the head can rotate with the head, allowing the diver to aim the viewport at the target, but peripheral vision is constrained by the dimensions of the viewport, the weight in air and unbalanced buoyancy forces when immersed must be carried by the neck, and inertial and hydrodynamic loads must be carried by the neck. A helmet fixed to a breastplate is supported by the torso, which can safely support much greater loads, but does not rotate with the head. The entire upper body must rotate to direct the field of vision. This makes it necessary to use larger viewports so the diver has an acceptable field of vision at times when rotating the body is impractical. The need to rotate the head inside the non-rotatable helmet requires internal clearance, therefore a large volume, and consequently a greater mass of ballast. Divers who need optical correction have choices. Contact lenses can be worn under all types of masks and helmets. Regular spectacles can be worn in most helmets, but can not be adjusted during the dive. Corrective lenses can be glued to the inside of half-masks and some full-face masks, but the distance from the eyes to the lenses may not be optimal. Bifocal arrangements are available, mostly for far-sightedness, and are popular with older divers to allow them to read their instruments. Defogging of bonded lenses is the same as for plain glass. Some dive computers have relatively large font displays, and adjustable brightness to suit the ambient lighting. Open circuit breathing apparatus produces exhalation gas bubbles at the exhaust ports. Free-flow systems produce the largest volumes, but the outlet can be behind the viewports so it does not obscure the diver's vision. Demand systems must have the second stage diaphragm and exhaust ports at approximately the same depth as the mouth or lungs to minimise work of breathing. To get consistent breathing effort for the range of postures the diver may need to assume, this is most practicable when the exhaust ports and valves are close to the mouth, so some form of ducting is required to direct the bubbles away from the viewports of helmet or mask. This generally diverts exhaust gases round the sides of the head, where they tend to be rather noisy as the bubbles rise past the ears. Closed circuit systems vent far less gas, which can be released behind the diver, and are significantly quieter. Diffuser systems have been tried, but have not been successful for open circuit equipment, though they have been used on rebreathers, where they improve stealth characteristics. The inside surface of the viewport of a mask or helmet tends to be prone to fogging, where tiny droplets of condensed water disperse light passing through the transparent material, blurring the view. Treating the inside surface with a defogging surfactant before the dive can reduce fogging, but it may occur anyway, and it must be possible to actively defog, either by rinsing with water or by blowing dry air over it until it is clear. There is no supply of dry air to a half-mask, but rinsing is easy and need only momentarily interrupt breathing. A spitcock may be provided on standard helmets for rinsing. Demand helmets generally have a free-flow supply valve which directs dry air over the inside of the faceplate. Full-face masks may use either rinsing or free-flow, depending on whether they are intended primarily for scuba or surface-supply.Security
Masks held in place by adjustable straps can be knocked off or moved from the correct position, allowing water to flood in. Half masks are more susceptible, but as the diver can still breathe with a flooded half mask this is not considered a major issue. Full-face masks are part of the breathing passage, and need to be more securely supported, usually by 4 or 5 adjustable straps, connected at the back of the head, but it is possible for them to be dislodged, so it must be possible for the diver to refit them sufficiently to continue breathing. Helmets are much more securely attached, and it is considered an emergency if they come off the head, as it is difficult for the diver to rectify the problem underwater, though it is usually still possible to breathe carefully if the free-flow valve is opened.Internal volume
The volume ofHelmet buoyancy
The weight of a lightweight demand helmet in air is about 15 kg. Underwater it is nearly neutrally buoyant so it is not an excessive static load on the neck. The helmet is a close fit to the head and moves with the head, allowing the diver to aim the viewport using head movement to compensate for the restricted field of vision. Free-flow helmets compensate for a potentially large dead space by a high gas flow rate, so that exhaled gas is flushed away before it can be rebreathed. They tend to have a large internal volume, and be heavier than demand helmets, and usually rest on the shoulders, so do not move with the head. As there is no need for an oro-nasal inner mask, they usually have a large viewport or several viewports to compensate for the fixed position. The diver can move the head inside the helmet to a limited extent, but to look around further, the diver must rotate the torso. The view downwards is particularly restricted, and requires the diver to bend over to see the area near the feet.Gloves
Glove fit is important for several reasons. Gloves that are too tight restrict movement and require more effort to grip, which causes early fatigue. Reduced blood flow may cause cramping. loose gloves may be ineffective against heat loss due to flushing, and may reduce dexterity due to excess bulk. There is a conflict between insulation and dexterity, and the reduction of tactile sense, grip strength, and early fatigue due to thick gloves or chilled hands. The diver can tolerate greater heat loss through the hands if the rest of the diver is warm, but in some cases such as diving in near-freezing water or where the air temperature at the surface is below freezing, the risk of frostbite or non-freezing cold injury necessitates the use of gloves most of the time. Suitable design of equipment can help make the work of correct operation easier. For safety-critical equipment, dexterity can make the difference between managing a problem adequately, or a situation deteriorating beyond recovery. Simple, large control interfaces such as oversize knobs and buttons, large clips, and tools that can be gripped by a heavily gloved hand can reduce risk significantly. In very cold water there are two problems causing loss of dexterity. The chilling of hands and fingers directly causes loss of feeling and strength of the hands, and thick gloves needed to reduce chilling also reduce the sensitivity of the fingertips, making it more difficult to feel what the fingers are doing. Thick gloves also make the fingertips wider and thicker and a poorer fit to components designed to be used by the naked hands. This is less of a problem with gloves where the fingertips have a reduced thickness of cover over the contact surface, but few neoprene gloves have this feature. The fingertips of the thumbs and forefingers are most affected, and also wear out faster than the rest of the glove. Some divers wear a thinner, tougher, work glove under the neoprene insulating glove, and cut the tips off the thumbs and forefingers of the neoprene gloves to expose the inner gloves as a workable compromise. Dry gloves allow the diver to tailor the inner insulating glove to suit the task. Insulation can be thicker where it affects dexterity least, and thinner where more sensitivity is needed. Long term grip strength is reduced by fatigue. If the glove requires effort to close the hand to hold an object, this will eventually tire the muscles involved, and grip will weaken sooner than when affected by cold alone. This is mitigated by gloves with a preform to fit a partly closed hand, and by more flexible glove materials. With dry gloves, the inner glove can be tailored to be thicker where the insulation will not interfere with grip effort, while the outer, watertight glove can be chosen to provide the necessary toughness and wear resistance.Cylinder configurations
When using multiple gas sources with multiple gas mixtures it can be critically important to avoid confusion of gas mix in use and pressure remaining in the various cylinders. The cylinder arrangement must allow access to cylinder valves when in the water. Use of the wrong gas for the depth can have fatal consequences without warning. High task loading for technical divers can distract from checking the mix when switching gas. It is important to check that each cylinder is what it should be and is mounted in the right place, to positively identify the new gas at each gas switch, and to adjust the decompression computer to allow for each change in gas for correct decompression. Some computers automatically change based on data from integrated pressure transducers, but still require correct pre-dive setting of gas mixes. Classical configurations: *Back-mounted single cylinder is stable on the diver in and out of the water, compact and acceptably balanced. Some divers have difficulty reaching the valve knob, which is behind the back, particularly when the cylinder is mounted relatively low on the harness, or the suit is thick or tight. *Back-mounted twins with isolation manifold are stable in and out of the water, compact, heavy, and acceptably balanced for most divers. Some divers have difficulty reaching the valve knobs behind the back. This can be a problem in a free-flow or leak emergency, where much gas can be lost due to inability to access knobs quickly to shut down. Weight and buoyancy distribution may be top heavy for some divers. *Back-mounted independent doubles. Gas is not available if a cylinder valve must be shut down. The side-mount emergency options of and are not available. *Flexible valve knob extensions on back mount sets are not very satisfactory and not very reliable, and are an additional snag risk. *Pony cylinders for bailout or decompression gas clamped to the main gas supply put the valve where it cannot be seen, and may be difficult to reach. They are reasonably compact and manageable out of the water. *Sling mount bailout and decompression cylinders allow easy access to the valve and visual check of labels on during gas switching. Up to four sling cylinders are reasonably manageable with some practice. Alternative configurations: *Inverted single or manifolded twin cylinders with valves at the bottom which are more reachable, but more vulnerable to impact damage. Custom hose lengths are needed, and hose routing will be different. This arrangement works for firefighters, and has been used by military divers. Weight and buoyancy distribution may be bottom heavy for some divers, and may adversely affect trim. This arrangement is also used for the gas cylinders on some models of rebreather. * Side mount provides much easier valve access, and it is possible to see the top of each cylinder to check the label when switching gas, which allows confirmation of correct gas. It is possible to hand off a cylinder when donating gas to another diver, so a long hose is not needed. The configuration has a lower profile than back mount, and it is possible to unclip cylinders for access of small openings. The configuration is clumsy out of water for crossing uneven terrain, and it can be difficult to mount more than one large cylinder each side when kitting up. Carrying six cylinders is probably more difficult when all are side-mounted than when two are back mounted. Lateral shift of centre of gravity as gas is consumed is noticeable. Buoyancy distribution of cylinders is top heavy due to the regulator and valve. Buoyancy changes when handing off or staging must be compensated, but this applies to all configurations. Buoyancy changes due to gas consumption can cause cylinders to hang awkwardly if the bottom ends start to float. Stuffing hoses under bungees on the cylinder can be awkward when the hands are full of other equipment like camera and reel, but necessary to avoid dangling regulators snagging on the environment. Adding buoyancy to the top of a cylinder to improve cylinder trim makes it necessary for the diver to carry extra weight. Bailout sets for surface-supplied diving are usually back mounted to keep the driver's arms and front clear for working. The position of the cylinder valve behind the shoulders where it does not interfere with head movement can be difficult to impossible for a helmeted diver to reach, particularly in an emergency. Therefore, the cylinder valve is conventionally opened fully before the dive and the bailout valve at the helmet closed. In diver jargon this is reported as "on at the tap, off at the hat" during pre-dive checks. An alternative arrangement which allows the diver easier access to the cylinder valve, is to wear the bailout cylinder inverted, with the cylinder valve in the small of the back where it is relatively easy to reach. This configuration requires a longer than standard second stage hose feeding intermediate pressure gas to the bailout block, but these are generally available off the shelf. The inverted arrangement may put the cylinder valve and regulator first stage at more risk of impact damage when the diver is out of the water, and when dressing the diver. Training specific to basic open circuit cylinder configuration is considered desirable, as the skills required are safety-critical, and vary significantly between the standard single back-mount, twin back-mount, back-mount with stage or bailout cylinders, and side-mount.Surface-supplied gas supply manifolds
Breathing gas supplied to divers from the surface is routed through a surface control manifold, the gas panel, and may also pass through a manifold in an open or closed diving bell. The surface gas panel may be operated by theInstrumentation and displays
Diving instrumentation may be for safety or to facilitate the task. The safety-critical information such as gas pressure and decompression status should be presented clearly and unambiguously. Lack of standardised dive computer user-interfaces can cause confusion under stress. Computer lock-out at times of great need is a potentially fatal design flaw. The meaning of alarms and warnings should be immediately obvious. The diver should be dealing with the problem, not trying to work out what it is. Displays should allow for variations in visual acuity, and be readable with colour-blindness. Ideally, critical displays should be readable without a mask, or provide for safe surfacing without a mask. There should not be too much distracting information on the main screen, and return to the main screen should be automatic by default, or auxiliary screens should continue to display critical decompression data. Dive computers are safety critical equipment, but there is very little formal training provided for their use, and models vary considerably in operation, and are often not intuitive, so skills are not transferable when a new unit is used. The user manual is usually all that is available to learn from, and it cannot be taken underwater for convenient reference. Human error in their use is quite common. Straps of wrist-mounts should be adjustable to suit ambidextrous wearing with a range of suits, and a single point strap failure should not result in loss of the instrument. Straps should be secure against sliding off the wrist in the event of suit compression when worn on the fore-arm. Instrument consoles represent a concentrated source of information, and a large potential for operator error. Head-up displays are sometimes used to alert the diver to changes that may require prompt response, usually related to gas concentrations in a rebreather loop. Audible alarms and warnings are commonly provided on dive computers, often as user options. These generally alert the diver to ascent rate, decompression ceiling, and oxygen partial pressure violations, so they can be corrected promptly. They can also be used to inform the diver when the no-stop limit is reached, or for gas integrated units, when pressure is getting low.Cutting tools
The primary function of diver cutting tools is to deal with entanglement by lines or nets. Preferably the tool should be accessible to both hands, and should be capable of cutting the diver free from any entanglement hazard predicted at the dive site. Many divers carry a cutting tool as standard equipment, and it may be required by code of practice as default procedure. When entanglement risk is high, backup cutting tools may be required.Dive lights
Dive lights may be needed to compensate for insufficient natural illumination or to restore colour. They may be carried in several ways depending on the purpose. Head mount lights are used by divers who need to use both hands for other purposes. With a head mount there is a greater risk of dazzling other divers in the vicinity, as the lights move with the diver's head, and this arrangement is more appropriate for divers who work or explore alone. Helmet mounts are appropriate for illuminating work which is monitored via a helmet-mounted closed circuit video camera. A wide beam allows good illumination of the field of vision of diver and video camera. Hand-held lights are directable by the diver independently of the direction the diver is facing and do not require any special mounting equipment, but occupy a hand, and are at risk of being dropped unless clipped on. They are most suitable for incidental lighting, and where precise direction is useful. Beam width and intensity preference depends on the application. High intensity, narrow beam lights are useful when the water is very clear, as they provide illumination at a greater distance for the same power output, which is useful for navigation and exploration. A wider beam may be more useful in low visibility and for work, where the diver needs to use a wider field of vision. Glove or Goodman handle mount allows precise direction and other use of the hand, but not always both at the same time. Canister lights allow the light head to be held in optional ways, and the cable prevents the light from falling far if dropped, and can be looped over the neck to suspend the light to illuminate close-up work, but is an additional encumbrance. It is possible and fairly common to carry more than one of these options. Where light is important for safety, the diver will carry backup lights. There are also special purpose light mounts, such as video and camera modelling lights, which must illuminate where the lens points, DPV headlights, internal and external bell lights, and ROV lights, which can be used to illuminate a work site to help the diver.Buddy lines
A buddy line is a line or strap physically tethering two scuba divers together underwater to prevent separation and as a means of communication in low visibility conditions. It is usually a short length and may be buoyant to reduce the risk of snagging on the bottom. It does not need to be particularly strong or secure, but should not pull free under moderate loads, such as when used for line signals. Divers may communicate by rope signals, but may just use the line to attract attention before moving closer and communicating by hand signals. The disadvantage of a buddy line is an increased risk of snagging and entanglement, and the risk is increased with a longer or thinner line. Divers may need to disconnect the line quickly at either end in an emergency, which can be done via a quick-release mechanism or by cutting the line, both of which require at least one free hand. A velcro strap requires no tools for release and can be released under tension.Clips and attachment points
Clips and attachment points should be reliable and must generally be operable by one hand with gloves suitable for the water temperature, without needing to see what is being done, as it may be dark, low visibility, or out of view. Single-hand operation is necessary where only one hand can reach, and is always preferable, as the other hand may be in use for something important at the time. While unlikely, it is possible for most types of clip to jam closed, and if this may endanger the diver it should be possible to use an alternative method to disconnect, which does not involve special tools. Cutting loose using theDiver propulsion vehicles
A diver propulsion vehicle (DPV) is a power supply with integral thruster used byCameras
Underwater cameras are usually popular models encased in a watertight pressure housing, though there have been a few notable exceptions, such as the Nikonos and Sea & Sea ranges, in which the camera body was the pressure housing. Controls are generally operated by movable links penetrating the watertight case, each requiring reliable seals, and each a potential leak. Compact and lightweight camera bodies with multiple controls packed into a small space tend to transform into bulky, heavy and expensive units when housed for moderately deep diving. Controls must be operable using thick gloves in cold water. Lighting varies depending on conditions, subject, lens, and other variables, and the use of modelling lights and external flash is common. These are usually supported by a camera tray and arms which allow the lightning to be aimed. This can make a camera setup very bulky and it may require most of the diver's attention. At the other extreme, a head-mounted sports video recorder may be triggered at the start of the dive and thereafter ignored until it is time to stop recording. For most underwater photography, a camera that is close to neutral buoyancy will be easier to handle and have less disruptive effect on diver trim. Strobe arms incorporating incompressible buoyancy compartments are the preferred system, as they do not need to be adjusted for changes of depth. Several manufacturers produce compact cameras that are inherently water-resistant to about 10 to 15 msw, and underwater housings rated to around 40 to 50 msw, which are small enough to fit into a large pocket, have a fairly large zoom range, and a large preview screen. Automatic focusing allows divers with imperfect vision to take acceptable photographs, and a minor housing leak is more an annoyance than a catastrophe, as the camera's own water resistance is a second line of defence. A large rear LCD screen viewfinder allows easy framing when automatic focusing is used. As the focus window usually changes colour when the autofocus is successful, the photographer can concentrate on framing and press the shutter release all the way when the focus icon turns green. Internal flash is problematic at anything except very close range, as it can cause backscatter in turbid water, and is the major consumer of battery power at full power. External flash using optical coupling avoids hull penetrations and associated potential leaks, and video lights give a good preview of exposure, and also provide the diver with a high-power dive light, which is pointing in the right direction to record the scene most of the time. With the more powerful video lights and low-light sensitive cameras, flash may not be necessary, or fill-in flash use may extend the battery life to a few hundred photos. A problem with underwater photography is inadvertent changing of camera settings, which may go unnoticed by the diver. The controls and operation of underwater cameras differ considerably, even between models by the same manufacturer, but as they do not affect diver safety, no training is required, and the diver is free to learn by their own experience, or find someone to provide informal type training.Surface marker buoys
A surface marker buoy that is towed for the whole dive to indicate the position of the diver throughout the dive should have sufficient buoyancy to reliably remain at the surface so it can be seen, and if it is to be actively towed, should not develop so much drag that the diver is unable to manage it effectively. The tow line may be a major source of drag, which is roughly proportional to its diameter, so a smaller, smooth line is preferable for low drag, and also fits on a more compact reel or spool. Smaller line may need to be of stronger and more abrasion resistant material likeDistance lines and line markers, reels and spools
Distance lines are used for underwater navigation where it is either essential to mark the route out of the overhead environment, or necessary or desirable to return to a specific point. Lines are deployed from reels or spools, and may be left in place or recovered on the return. Line markers are generally used on permanent guidelines to provide critical information to divers following the line. The slots and notches provided are used to wrap the line to secure the marker in place. A simple passage of the line through the enlarged area at the base of the two slots will allow the marker to slide along the line, or even fall off if brushed by a diver. To more securely fasten the marker, an extra wrap may be added at each slot. It must be possible to fit, interpret and remove a line marker by feel in total darkness with the line under moderate tension without dislodging the line. The basic function of these markers is fairly consistent internationally, but procedures may differ by region, and between teams. The protocol for placement and removal should be well understood by the members of a specific team. ADiving chambers
Design and construction of pressure vessels for human occupancy are regulated by law, safety standards, andHyperbaric stretchers
A hyperbaric stretcher is a lightweight pressure vessel for human occupancy (PVHO) designed to accommodate one person undergoing initial hyperbaric treatment during or while awaiting transport or transfer to a treatmentHyperbaric rescue and escape systems
A saturated diver who needs to be evacuated should preferably be transported without a significant change in ambient pressure. Hyperbaric evacuation requires pressurised transportation equipment, and could be required in a range of situations. The pressure rating and locking mechanism of the evacuation chamber must be compatible with the saturation system it is to serve, and the reception facility, as both transfers must be under pressure, and it may not be safe to start decompression during the evacuation.Equipment storage on dive boats and dive preparation areas
While it is possible for a diver to put on and take off some items of equipment in the water, there is a greater risk of fitting them incorrectly or losing them, particularly when the water is a bit rough. Doing this in the surf is even more risky, and delays at the surface on a boat dive can let the divers drift off site. When possible, kit-up and pre-dive checks should be completed on shore or on the boat, and the kit-up area should facilitate this, or at least make it possible. For recreational diving charter boats, this gives preference to arrangements where each diver can safely and securely stow all their personal dive gear at the same place where they will be putting it on, and where it is not necessary for it to be handled by anyone else except at the diver's request, as unauthorised handling of another person's life-support equipment could have legal consequences if something goes wrong. Boarding the boat after a dive may require equipment to be removed, and this presents another set of hazards, and the associated risks of injury and damage to or loss of equipment, some of which may be avoided if the diver does not have to take off equipment in the water, and heavy equipment does not have to be lifted over the side of the boat with fragile dangling components exposed to snagging, impact, and crushing hazards. The requirement to remove fins before climbing some ladders reduces the diver's ability to swim back to the boat if they drift away. When boarding an anchored boat, some way of keeping within reach of the boarding area while removing equipment is required, and it may be necessary to use both hands to ensure secure removal and hand-over of some equipment.Access equipment
This includes the equipment needed to get into and out of the water. In most cases, this refers to diving from a floating platform, but also applies to shore dives where access requires equipment.Diving stages and wet bells
Diving stages and wet bells are open platforms used to lower the divers to the work site and to control the ascent and in-water decompression, and to provide safe and easy entry and exit from the water. Design must provide space for the working diver and where appropriate, the bellman, in positions where they are protected from impact during transit and prevented from falling out when above the water. The divers may be seated, but more usually stand during transit. A stage must have a way to guide the umbilical from the surface tending point to the diver so the diver can be sure of finding the right way back to the stage. This can be provided by having the diver exit the stage on the opposite side to boarding, with the umbilical passing through the frame, but this is not infallible in bad visibility, and a closed fairlead is more reliable. Running the umbilical via the stage may also be needed to ensure the diver cannot approach known hazards, such as the thrusters of a dynamically positioned vessel. A wet bell has an open-bottomed air space at the top, large enough for the diver and bellman's heads, intended as a place of refuge in an emergency, where some breathing problems can be managed. The air space must be large enough for an unresponsive diver to be suspended by their harness with their head in the air space, as it may be necessary to remove an unresponsive diver's helmet or full-face mask to provide first aid. The bell is also provided with an on-board emergency gas supply, sufficient for any planned or reasonably foreseeable decompression, and a means of safely switching between surface and on-board gas supply. This necessitates an on-board gas distribution manifold and divers' umbilicals that are deployed from and stored on the bell, and someone to operate the panel and tend the working diver's excursion umbilical. The bellman does this, and also serves as standby diver. The buoyancy of the air space may have to be compensated by ballast, as the bell must be negatively buoyant during normal operation.Diver ladders
For some applications, dive boat ladders that allow the diver to ascend without removing the fins are preferred. When there is a lot of relative motion between the diver and ladder, it can become difficult to safely remove fins, then get onto the ladder, and not lose the fins. A ladder that can be climbed with fins on the feet avoids this problem. A ladder that slopes at an angle of about 15° from the vertical reduces the load on the arms. If a ladder is to be climbed in full equipment, suitable handholds to brace the diver while climbing the upper rungs and moving onto the deck to the place where gear will be removed are necessary for safety. This also applies if the divers need to climb down a ladder wearing dive gear, and they may need to turn round at the top of the ladder. In the general case, the vessel will be moving in a seaway while the diver is boarding.Dive platforms and diver lifts
A dive platform, or swim platform, is a near horizontal surface on a dive boat giving more convenient access to the water than the deck. It may be large enough for several divers to use simultaneously, or just enough for a single diver. The platform may be fixed, folding, or arranged to lower divers into the water and lift them out again, also known as a diver lift. Most dive platforms are mounted at the stern, usually on the transom, at a height a short distance above the waterline. They are easily flooded by a following sea, and are self-draining. Fixed and folding platforms are generally provided with ladders which can be folded or lifted out of the water when not in use, and steps or ladders from the platform to the deck, while lifting platforms may be sufficiently immersible for the divers to swim directly over the platform and stand up to be lifted to a level where they can walk off onto the deck. Lifts are commonly mounted on the transom, or on the side of the boat. Handrails for use while using steps, ladders and lifts, when crossing or waiting on the platform, or making adjustments to equipment are a valuable safety adjunct as the platform will often be moving when in use, and the divers will usually be encumbered by heavy and bulky diving equipment. Barriers to protect occupants from pinch point hazards may be necessary when there are moving parts. The utility of a lift is enhanced if the diver can use it without having to remove any equipment in the water or on the platform, so an upper position level with the working deck and sufficient space to walk onto the deck fully kitted is preferable. Fixed platforms giving easy access to the water are also sometimes provided at shore diving sites, such as flooded quarries used for diver training, or coastal jetties.Recovery of an incapacitated diver
Professional divers may be required to wear a harness suitable for lifting the diver out of the water in an emergency, and there will usually be an emergency recovery plan and the necessary extraction equipment and personnel available. Private recreational divers are not usually required to make any special provisions for an emergency, but recreational diving service providers may have a duty of care to their customers to provide for reasonably foreseeable emergencies with reasonably practicable facilities. There may be a regional or membership organisation standard or code of practice. Getting an incapacitated diver out of the water onto a boat or the shore for first aid would usually be considered an expected level of care. Recreational divers are not required to wear lifting grade harness, so other plans should be in place, and these often necessitate removing equipment from the diver, and the risk of losing the equipment. Details of methods to recover a diver into a boat will vary depending on the geometry of the boat. Simply dragging a diver over the pontoon of an inflatable hull may work in many cases. Larger boats with higher freeboard may have lifting gear that can be put to use with a rescue sling. A diver lift is capable of lifting a diver, but some arrangements must be made to keep the diver in a safe position on the lift while lifting.Tools
Tools that are intended for use by divers should take into account the handicaps of the underwater environment on operator stability, mobility and control, within the full range of conditions in which they are likely to be used. Buoyancy effects on tool and operator, water movement, and reduced sensory input can complicate underwater tool use. Use with gloves is common, and can be a problem when controls are small and clustered.Tool bags, pockets and lanyards
Lanyards and clipping points can prevent loss of tools and equipment like cameras, lights and cutting tools in mid-water or poor visibility, but can increase entanglement risk. Carrying heavy tools can compromise the diver's ability to accurately control ascent and descent rates, so it is common practice for professional divers to have their tools delivered in a bag lowered from the surface, or to transport them in a basket on the stage or bell which transports the diver to the underwater workplace. Tools do not have to be carried inside the pressurised volume of a closed bell, so the basket or rack can be on the bell stage orPhysiological variables
Checklists
Checklists for preparation of the dive and diving equipment are regarded as important safety tools, and are mandatory in some circumstances. There are several design factors which affect the effectiveness of checklists.See also
* * * * *References
{{Underwater diving, divequ Diving equipment Design Ergonomics