Grumman XTSF

The Grumman XTSF was a proposed twin-engine torpedo scout aircraft, designed by Grumman for the United States Navy towards the end of World War II. Based on the design of the Grumman F7F Tigercat fighter, but enlarged and with the addition of a bomb bay, the XTSF was deemed too large for carrier operations, and the project was cancelled before any aircraft were built. Instead, the Navy chose to order the single-engine XTB3F, which became the successful AF Guardian.

Design and development

In 1944, it was determined that the Grumman XTB2F, then under development for the Navy, would be too large to practically and safely operate from aircraft carriers.Goebel 2009 Even the new s, known as "battle carriers" (CVB) and the largest aircraft carriers built by any nation to that point, would have difficulty operating the massive aircraft, which was the size of a U.S. Army Air Force medium bomber. As a result, in late June 1944, Grumman submitted its G-66 design to the Bureau of Aeronautics (BuAer). After a review of the design by BuAer during the following month, a revised design was submitted, and on August 17 the existing contract for the XTB2F was modified to instead order two XTSF-1 aircraft, to be based on Grumman's F7F-2 Tigercat two-seat, twin-engined fighter-bomber, the first prototype intended to be a conversion of a F7F airframe.

A mid-wing, all-metal, cantilever monoplane with two Pratt & Whitney Double Wasp radial engines mounted in streamlined nacelles under the wing,Angelucci 1987, p. 238. the XTSF-1 was intended to carry two crew members in tandem seats, and featured an internal bomb bay and an SCR-720 radar set, the radar later being replaced in the design by an AN/APS-3 or AN/APS-4 set. A second seat was added for the radar operator.

The outer wing of the XTSF was lengthened by compared to that of the F7F-2, while the size of the horizontal stabilizer was increased by ). The vertical stabilizer was also enlarged, while the aircraft's weight increased by almost over that of the Tigercat.

The wings folded upwards for stowage aboard aircraft carriers, while the undercarriage and arrestor hook were hydraulically operated. Gun armament was planned to be four .50 caliber (12.7 mm) Browning M2 machine guns, or, alternatively, two 20 mm Hispano cannon, while a bomb bay based on that of the Grumman TBF Avenger was installed in a fuselage stretched by .

Cancellation

A mockup of the cockpit, center fuselage, and wing center section was built and was inspected by the BuAer in the fall 1944.Johnson 2008, p. 427 However, the contract for the prototype XTSF-1s was terminated in January 1945. This was due to a variety of factors, including the Navy's belief that the Grumman engineers and factory were already at capacity producing the F6F Hellcat, the F7F, and the F8F Bearcat,Norton 2008, p. 121 that the XTSF-1 would be too large for practical operations from escort carriers, and because it was believed the Grumman G-70, to be built as the XTB3F, was a better prospect. In addition, the F7F was proving difficult to certify for operations from aircraft carriers,Meyer 2002, p. 55 further prejudicing the Navy against the design.

Some sources erroneously state that the XTSF-1 became the XTB2F,Lawson and Tillman 2001, p. 87 however this is not the case.Norton 2008, p. 120 The XTSF-1 was the only aircraft ever designated by the U.S. Navy in the 'TS for Torpedo Scout' category, the designation being superseded and incorporated, along with 'BT for Bomber-Torpedo', 'SB for Scout-Bomber', and 'TB for Torpedo-Bomber', into the new 'A for Attack' series."U.S. Systems of Aircraft Designation"
''driko.org''. Accessed May 8, 2010.

Specifications (XTSF-1)

See also

References

Citations

Bibliography

*
*
*
*
*
*
*

External links

*


''The Grumman Pages''.


''U.S. Military Aircraft and Weapon Designations''

{{Good article

TS01F
Cancelled military aircraft projects of the United States
High-wing aircraft
Carrier-based aircraft
Twin piston-engined tractor aircraft