Euler equations (fluid dynamics)

In fluid dynamics, the Euler equations are a set of quasilinear partial differential equations governing adiabatic and inviscid flow. They are named after Leonhard Euler. In particular, they correspond to the Navier–Stokes equations with zero viscosity and zero thermal conductivity.

The Euler equations can be applied to incompressible or compressible flow. The incompressible Euler equations consist of Cauchy equations for conservation of mass and balance of momentum, together with the incompressibility condition that the flow velocity is a solenoidal field. The compressible Euler equations consist of equations for conservation of mass, balance of momentum, and balance of energy, together with a suitable constitutive equation for the specific energy density of the fluid. Historically, only the equations of conservation of mass and balance of momentum were derived by Euler. However, fluid dynamics literature often refers to the full set of the compressible Euler equations – including the energy equation – as "the compressible Euler equations".

The mathematical characters of the incompressible and compressible Euler equations are rather different. For constant fluid density, the incompressible equations can be written as a quasilinear advection equation for the fluid velocity together with an elliptic Poisson's equation for the pressure. On the other hand, the compressible Euler equations form a quasilinear hyperbolic system of conservation equations.

The Euler equations can be formulated in a "convective form" (also called the " Lagrangian form") or a "conservation form" (also called the " Eulerian form"). The convective form emphasizes changes to the state in a frame of reference moving with the fluid. The conservation form emphasizes the mathematical interpretation of the equations as conservation equations for a control volume fixed in space (which is useful
from a numerical point of view).

History

The Euler equations first appeared in published form in Euler's article "Principes généraux du mouvement des fluides", published in ''Mémoires de l'Académie des Sciences de Berlin'' in 1757 (although Euler had previously presented his work to the Berlin Academy in 1752).
The Euler equations were among the first partial differential equations to be written down, after the wave equation. In Euler's original work, the system of equations consisted of the momentum and continuity equations, and thus was underdetermined except in the case of an incompressible flow. An additional equation, which was called the adiabatic condition, was supplied by Pierre-Simon Laplace in 1816.

During the second half of the 19th century, it was found that the equation related to the balance of energy must at all times be kept for compressible flows, and the adiabatic condition is a consequence of the fundamental laws in the case of smooth solutions. With the discovery of the special theory of relativity, the concepts of energy density, momentum density, and stress were unified into the concept of the stress–energy tensor, and energy and momentum were likewise unified into a single concept, the energy–momentum vector.

Incompressible Euler equations with constant and uniform density

In convective form (i.e., the form with the convective operator made explicit in the momentum equation), the incompressible Euler equations in case of density constant in time and uniform in space are:

where:
*$\mathbf u$ is the flow velocity vector, with components in an ''N''-dimensional space $u_1, u_2, \dots, u_N$,
*$=+\mathbf u\cdot\nabla\mathbf v$, for a generic function (or field) $\mathbf v$ denotes its material derivative in time with respect to the advective field $\mathbf u$ and
*$\nabla w$ is the gradient of the specific (with the sense of ''per unit mass'') thermodynamic work, the internal source term, and
*$\nabla \cdot \mathbf u$ is the flow velocity divergence.
* $\mathbf$ represents body accelerations (per unit mass) acting on the continuum, for example gravity, inertial accelerations, electric field acceleration, and so on.

The first equation is the Euler momentum equation with uniform density (for this equation it could also not be constant in time). By expanding the material derivative, the equations become:

:$\left\ Euler equations in the Froude limit (no external field) are named free equations and are conservative. The limit of high Froude numbers (low external field) is thus notable and can be studied with$perturbation theory.

Conservation form

The conservation form emphasizes the mathematical properties of Euler equations, and especially the contracted form is often the most convenient one for computational fluid dynamics simulations. Computationally, there are some advantages in using the conserved variables. This gives rise to a large class of numerical methods
called conservative methods.

The free Euler equations are conservative, in the sense they are equivalent to a conservation equation:

:$\frac+ \nabla \cdot \mathbf F =,$

or simply in Einstein notation:

:$\frac+ \frac= 0_i,$

where the conservation quantity $\mathbf y$ in this case is a vector, and $\mathbf F$ is a flux matrix. This can be simply proved.

At last Euler equations can be recast into the particular equation:

Spatial dimensions

For certain problems, especially when used to analyze compressible flow in a duct or in case the flow is cylindrically or spherically symmetric, the one-dimensional Euler equations are a useful first approximation. Generally, the Euler equations are solved by Riemann's method of characteristics. This involves finding curves in plane of independent variables (i.e., $x$ and $t$) along which partial differential equations (PDEs) degenerate into ordinary differential equations (ODEs). Numerical solutions of the Euler equations rely heavily on the method of characteristics.

Incompressible Euler equations

In convective form the incompressible Euler equations in case of density variable in space are:

where the additional variables are:
*$\rho$ is the fluid mass density,
*$p$ is the pressure, $p = \rho w$.

The first equation, which is the new one, is the incompressible continuity equation. In fact the general continuity equation would be:

:$+ \mathbf u \cdot \nabla \rho + \rho \nabla \cdot \mathbf u = 0$

but here the last term is identically zero for the incompressibility constraint.

Conservation form

The incompressible Euler equations in the Froude limit are equivalent to a single conservation equation with conserved quantity and associated flux respectively:

:$=\begin\rho \\ \rho \mathbf u \\0\end; \qquad =\begin\rho \mathbf u\\\rho \mathbf u \otimes \mathbf u + p \mathbf I\\\mathbf u\end.$

Here $\mathbf y$ has length $N+2$ and $\mathbf F$ has size $(N+2)N$. In general (not only in the Froude limit) Euler equations are expressible as:

:$\frac \begin\rho \\ \rho \mathbf u \\0\end+ \nabla \cdot \begin\rho \mathbf u\\\rho \mathbf u \otimes \mathbf u + p \mathbf I\\ \mathbf u\end = \begin0 \\ \rho \mathbf g \\ 0 \end$

Conservation variables

The variables for the equations in conservation form are not yet optimised. In fact we could define:

:$=\begin\rho \\ \mathbf j \\0\end; \qquad =\begin \mathbf j \\ \frac \rho \, \mathbf j \otimes \mathbf j+ p \mathbf I\\ \frac \mathbf j \rho \end.$

where:
* $\mathbf j = \rho \mathbf u$ is the momentum density, a conservation variable.

where:
* $\mathbf f = \rho \mathbf g$ is the force density, a conservation variable.

Euler equations

In differential convective form, the compressible (and most general) Euler equations can be written shortly with the material derivative notation:

&= -\frac + \mathbf \\ .2ex &= -\frac\nabla \cdot \mathbf
\end\right.
, cellpadding
, border
, border colour = #FF0000
, background colour = #ECFCF4

where the additional variables here is:
*$e$ is the specific internal energy (internal energy per unit mass).

The equations above thus represent conservation of mass, momentum, and energy: the energy equation expressed in the variable internal energy allows to understand the link with the incompressible case, but it is not in the simplest form.
Mass density, flow velocity and pressure are the so-called ''convective variables'' (or physical variables, or lagrangian variables), while mass density, momentum density and total energy density are the so-called ''conserved variables'' (also called eulerian, or mathematical variables).

If one expands the material derivative the equations above are:

:\left\}

For a thermodynamic fluid, the compressible Euler equations are consequently best written as:

&= ve_\nabla v + ve_\nabla s + \mathbf \\ .2ex &= 0
\end\right.
, cellpadding
, border
, border colour = #FFFF00
, background colour = #ECFCF4

where:
* $v$ is the specific volume
* $\mathbf u$ is the flow velocity vector
* $s$ is the specific entropy

In the general case and not only in the incompressible case, the energy equation means that for an inviscid thermodynamic fluid the specific entropy is constant along the flow lines, also in a time-dependent flow. Basing on the mass conservation equation, one can put this equation in the conservation form:

:$+ \nabla \cdot (\rho s \mathbf u) = 0$

meaning that for an inviscid nonconductive flow a continuity equation holds for the entropy.

On the other hand, the two second-order partial derivatives of the specific internal energy in the momentum equation require the specification of the fundamental equation of state of the material considered, i.e. of the specific internal energy as function of the two variables specific volume and specific entropy:

:$e = e(v, s)$

The ''fundamental'' equation of state contains all the thermodynamic information about the system (Callen, 1985), exactly like the couple of a ''thermal'' equation of state together with a ''caloric'' equation of state.

Conservation form

The Euler equations in the Froude limit are equivalent to a single conservation equation with conserved quantity and associated flux respectively:

:$= \begin \rho \\ \mathbf j \\ E^t \end; \qquad = \begin \mathbf j \\ \frac 1 \rho \mathbf j \otimes \mathbf j + p \mathbf I \\ \left(E^t + p\right) \frac\mathbf \end.$

where:
* $\mathbf j = \rho \mathbf u$ is the momentum density, a conservation variable.
* $E^t = \rho e + \frac \rho u^2$ is the total energy density (total energy per unit volume).

Here $\mathbf y$ has length N + 2 and $\mathbf F$ has size N(N + 2). In general (not only in the Froude limit) Euler equations are expressible as:

where:
* $\mathbf f = \rho \mathbf g$ is the force density, a conservation variable.

We remark that also the Euler equation even when conservative (no external field, Froude limit) have no Riemann invariants in general. Some further assumptions are required

However, we already mentioned that for a thermodynamic fluid the equation for the total energy density is equivalent to the conservation equation:

:$(\rho s) + \nabla \cdot (\rho s \mathbf u) = 0$

Then the conservation equations in the case of a thermodynamic fluid are more simply expressed as:

\end =
\begin0 \\ \mathbf \\ 0 \end

, cellpadding
, border
, border colour = #FFFF00
, background colour = #ECFCF4

where:
* $S = \rho s$ is the entropy density, a thermodynamic conservation variable.

Another possible form for the energy equation, being particularly useful for isobarics, is:

:$\frac + \nabla \cdot \left(H^t \mathbf u\right) = \mathbf u \cdot \mathbf f - \frac$

where:
*$H^t = E^t + p = \rho e + p + \frac \rho u^2$ is the total enthalpy density.

Quasilinear form and characteristic equations

Expanding the fluxes can be an important part of constructing numerical solvers, for example by exploiting ( approximate) solutions to the Riemann problem. In regions where the state vector ''y'' varies smoothly, the equations in conservative form can be put in quasilinear form :

:$\frac + \mathbf A_i \frac = .$

where $\mathbf A_i$ are called the flux Jacobians defined as the matrices:

:$\mathbf A_i (\mathbf y)=\frac.$

Obviously this Jacobian does not exist in discontinuity regions (e.g. contact discontinuities, shock waves in inviscid nonconductive flows). If the flux Jacobians $\mathbf A_i$ are not functions of the state vector $\mathbf y$, the equations reveals ''linear''.

Characteristic equations

The compressible Euler equations can be decoupled into a set of N+2 wave equations that describes sound in Eulerian continuum if they are expressed in characteristic variables instead of conserved variables.

In fact the tensor A is always diagonalizable. If the eigenvalues (the case of Euler equations) are all real the system is defined ''hyperbolic'', and physically eigenvalues represent the speeds of propagation of information. If they are all distinguished, the system is defined ''strictly hyperbolic'' (it will be proved to be the case of one-dimensional Euler equations). Furthermore, diagonalisation of compressible Euler equation is easier when the energy equation is expressed in the variable entropy (i.e. with equations for thermodynamic fluids) than in other energy variables. This will become clear by considering the 1D case.

If $\mathbf p_i$ is the right eigenvector of the matrix $\mathbf A$ corresponding to the eigenvalue $\lambda_i$, by building the projection matrix:

:\mathbf = \left mathbf_1, \mathbf_2, ..., \mathbf_n\right/math>

One can finally find the ''characteristic variables'' as:

:$\mathbf= \mathbf^\mathbf,$

Since A is constant, multiplying the original 1-D equation in flux-Jacobian form with P⁻¹ yields the characteristic equations:

:$\frac + \lambda_j \frac = 0_i$

The original equations have been decoupled into N+2 characteristic equations each describing a simple wave, with the eigenvalues being the wave speeds. The variables ''w''_i are called the ''characteristic variables'' and are a subset of the conservative variables. The solution of the initial value problem in terms of characteristic variables is finally very simple. In one spatial dimension it is:

:$w_i(x, t) = w_i\left(x - \lambda_i t, 0\right)$

Then the solution in terms of the original conservative variables is obtained by transforming back:

:$\mathbf = \mathbf \mathbf,$

this computation can be explicited as the linear combination of the eigenvectors:

:$\mathbf(x, t) = \sum_^m w_i\left(x - \lambda_i t, 0\right) \mathbf p_i,$

Now it becomes apparent that the characteristic variables act as weights in the linear combination of the jacobian eigenvectors. The solution can be seen as superposition of waves, each of which is advected independently without change in shape. Each ''i''-th wave has shape ''w''_''i''''p''_''i'' and speed of propagation ''λ''_''i''. In the following we show a very simple example of this solution procedure.

Waves in 1D inviscid, nonconductive thermodynamic fluid

If one considers Euler equations for a thermodynamic fluid with the two further assumptions of one spatial dimension and free (no external field: ''g'' = 0) :

:\left\{\begin{align}
{\partial v \over \partial t} + u{\partial v \over \partial x} - v {\partial u \over \partial x} &= 0 \\ .2ex {\partial u \over \partial t} + u{\partial u \over \partial x} - e_{vv} v {\partial v \over \partial x} - e_{vs}v {\partial s \over \partial x} &= 0 \\ .2ex {\partial s \over \partial t} + u{\partial s \over \partial x} &= 0
\end{align}\right.

If one defines the vector of variables:

:$\mathbf{y} = \begin{pmatrix}v \\ u \\ s\end{pmatrix}$

recalling that $v$ is the specific volume, $u$ the flow speed, $s$ the specific entropy, the corresponding jacobian matrix is:

: ${\mathbf A}=\begin{pmatrix}u & -v & 0 \\ - e_{vv} v & u & - e_{vs} v \\ 0 & 0 & u \end{pmatrix}.$

At first one must find the eigenvalues of this matrix by solving the characteristic equation:

: $\det(\mathbf A(\mathbf y) - \lambda(\mathbf y) \mathbf I) = 0$

that is explicitly:

: $\det\begin{bmatrix}u-\lambda & -v & 0 \\ - e_{vv} v & u-\lambda & - e_{vs} v \\ 0 & 0 & u-\lambda \end{bmatrix}=0$

This determinant is very simple: the fastest computation starts on the last row, since it has the highest number of zero elements.

: $(u-\lambda) \det \begin{bmatrix}u-\lambda & -v \\ - e_{vv} v & u -\lambda \end{bmatrix}=0$

Now by computing the determinant 2×2:

: $(u - \lambda)\left((u - \lambda)^2 - e_{vv} v^2\right) = 0$

by defining the parameter:

: $a(v,s) \equiv v \sqrt {e_{vv$

or equivalently in mechanical variables, as:

: $a(\rho,p) \equiv \sqrt {\partial p \over \partial \rho}$

This parameter is always real according to the second law of thermodynamics. In fact the second law of thermodynamics can be expressed by several postulates. The most elementary of them in mathematical terms is the statement of convexity of the fundamental equation of state, i.e. the hessian matrix of the specific energy expressed as function of specific volume and specific entropy:

: $\begin{pmatrix}e_{vv} & e_{vs} \\ e_{vs} & e_{ss} \end{pmatrix}$

is defined positive. This statement corresponds to the two conditions:

:\left\{\begin{align}
e_{vv} &> 0 \\ .2ex e_{vv}e_{ss} - e_{vs}^2 &> 0
\end{align}\right.

The first condition is the one ensuring the parameter ''a'' is defined real.

The characteristic equation finally results:

: $(u - \lambda)\left((u - \lambda)^2 - a^2\right) = 0$

That has three real solutions:

: $\lambda_1(v,u,s) = u-a(v,s) \quad \lambda_2(u)= u, \quad \lambda_3(v,u,s) = u+a(v,s)$

Then the matrix has three real eigenvalues all distinguished: the 1D Euler equations are a strictly hyperbolic system.

At this point one should determine the three eigenvectors: each one is obtained by substituting one eigenvalue in the eigenvalue equation and then solving it. By substituting the first eigenvalue λ₁ one obtains:

: $\begin{pmatrix}a & -v & 0 \\ - e_{vv} v & a & - e_{vs} v \\ 0 & 0 & a \end{pmatrix} \begin{pmatrix}v_1\\ u_1 \\s_1 \end{pmatrix}=0$

Basing on the third equation that simply has solution s₁=0, the system reduces to:

: $\begin{pmatrix}a & -v \\-a^2 /v& a \end{pmatrix} \begin{pmatrix}v_1\\ u_1 \end{pmatrix}=0$

The two equations are redundant as usual, then the eigenvector is defined with a multiplying constant. We choose as right eigenvector:

: $\mathbf p_1=\begin{pmatrix}v\\ a \\0\end{pmatrix}$

The other two eigenvectors can be found with analogous procedure as:

: $\mathbf p_2=\begin{pmatrix} e_{vs} \\ 0\\ - \left(\frac a v \right)^2 \end{pmatrix}, \qquad \mathbf p_3=\begin{pmatrix}v\\ -a \\0\end{pmatrix}$

Then the projection matrix can be built:

: $\mathbf P (v,u,s)=( \mathbf{p}_1, \mathbf{p}_2, \mathbf{p}_3) =\begin{pmatrix} v & e_{vs} & v\\ a & 0 & -a \\ 0 & - \left(\frac a v \right)^2 & 0 \end{pmatrix}$

Finally it becomes apparent that the real parameter ''a'' previously defined is the speed of propagation of the information characteristic of the hyperbolic system made of Euler equations, i.e. it is the '' wave speed''. It remains to be shown that the sound speed corresponds to the particular case of an isentropic transformation:

:$a_s \equiv \sqrt {\left({\partial p \over \partial \rho} \right)_s}$

Compressibility and sound speed

Sound speed is defined as the wavespeed of an isentropic transformation:

:$a_s(\rho,p) \equiv \sqrt {\left({\partial p \over \partial \rho} \right)_s}$

by the definition of the isoentropic compressibility:

:$K_s (\rho,p) \equiv \frac 1 \rho \left({\partial p \over \partial \rho} \right)_s$

the soundspeed results always the square root of ratio between the isentropic compressibility and the density:

:$a_s \equiv \sqrt {\frac {K_s} \rho}$

Ideal gas

The sound speed in an ideal gas depends only on its temperature:

:$a_s (T) = \sqrt {\gamma \frac T m}$

Since the specific enthalpy in an ideal gas is proportional to its temperature:

:$h = c_p T = \frac {\gamma}{\gamma-1} \frac T m$

the sound speed in an ideal gas can also be made dependent only on its specific enthalpy:

:$a_s (h) = \sqrt {(\gamma -1) h}$

Bernoulli's theorem for steady inviscid flow

Bernoulli's theorem is a direct consequence of the Euler equations.

Incompressible case and Lamb's form

The vector calculus identity of the cross product of a curl holds:

:$\mathbf{v \ \times } \left( \mathbf{ \nabla \times F} \right) = \nabla_F \left( \mathbf{v \cdot F } \right) - \mathbf{v \cdot \nabla } \mathbf{ F} \ ,$

where the Feynman subscript notation $\nabla_F$ is used, which means the subscripted gradient operates only on the factor $\mathbf F$.

Lamb in his famous classical book Hydrodynamics (1895), still in print, used this identity to change the convective term of the flow velocity in rotational form:

:$\mathbf u \cdot \nabla \mathbf u = \frac{1}{2}\nabla\left(u^2\right) + (\nabla \times \mathbf u) \times \mathbf u$

the Euler momentum equation in Lamb's form becomes:

:$\frac{\partial\mathbf{u{\partial t} + \frac{1}{2}\nabla\left(u^2\right) + (\nabla \times \mathbf{u}) \times \mathbf{u} + \frac{\nabla p}{\rho} = \mathbf{g} = \frac{\partial\mathbf{u{\partial t} + \frac{1}{2}\nabla\left(u^2\right) - \mathbf{u} \times (\nabla \times \mathbf{u}) + \frac{\nabla p}{\rho}$

Now, basing on the other identity:

:$\nabla \left( \frac {p}{\rho} \right) = \frac {\nabla p}{\rho} - \frac{p}{\rho^2} \nabla \rho$

the Euler momentum equation assumes a form that is optimal to demonstrate Bernoulli's theorem for steady flows:

:$\nabla \left(\frac{1}{2}u^2 + \frac{p}{\rho}\right) - \mathbf g = -\frac{p}{\rho^2} \nabla \rho + \mathbf u \times (\nabla \times \mathbf u) - \frac{\partial \mathbf u}{\partial t}$

In fact, in case of an external conservative field, by defining its potential φ:

:$\nabla \left( \frac 1 2 u^2 + \phi + \frac p \rho \right) = -\frac{p}{\rho^2} \nabla \rho + \mathbf u \times (\nabla \times \mathbf u) - \frac{\partial \mathbf u}{\partial t}$

In case of a steady flow the time derivative of the flow velocity disappears, so the momentum equation becomes:

:$\nabla \left( \frac 1 2 u^2 + \phi + \frac p \rho \right) = -\frac{p}{\rho^2} \nabla \rho + \mathbf u \times (\nabla \times \mathbf u)$

And by projecting the momentum equation on the flow direction, i.e. along a '' streamline'', the cross product disappears because its result is always perpendicular to the velocity:

:$\mathbf u \cdot \nabla \left(\frac{1}{2}u^2 + \phi + \frac{p}{\rho}\right) = -\frac{p}{\rho^2} \mathbf u \cdot \nabla\rho$

In the steady incompressible case the mass equation is simply:

:$\mathbf u \cdot \nabla \rho = 0$,

that is the mass conservation for a steady incompressible flow states that the density along a streamline is constant. Then the Euler momentum equation in the steady incompressible case becomes:

:$\mathbf u \cdot \nabla \left( \frac 1 2 u^2 + \phi + \frac p \rho \right) = 0$

The convenience of defining the total head for an inviscid liquid flow is now apparent:

:$b_l \equiv \frac 1 2 u^2 + \phi + \frac p \rho ,$

which may be simply written as:

:$\mathbf u \cdot \nabla b_l = 0$

That is, the momentum balance for a steady inviscid and incompressible flow in an external conservative field states that the total head along a streamline is constant.

Compressible case

In the most general steady (compressibile) case the mass equation in conservation form is:

:$\nabla \cdot \mathbf j = \rho \nabla \cdot \mathbf u + \mathbf u \cdot \nabla \rho = 0$ .

Therefore, the previous expression is rather

:$\mathbf{u} \cdot \nabla \left({\frac{1}{2u^2 + \phi + \frac{p}{\rho}\right) = \frac{p}{\rho}\nabla \cdot \mathbf{u}$

The right-hand side appears on the energy equation in convective form, which on the steady state reads:

:$\mathbf u \cdot \nabla e = - \frac{p}{\rho} \nabla \cdot \mathbf u$

The energy equation therefore becomes:

:$\mathbf u \cdot \nabla \left( e + \frac p \rho + \frac 1 2 u^2 + \phi \right) = 0,$

so that the internal specific energy now features in the head.

Since the external field potential is usually small compared to the other terms, it is convenient to group the latter ones in the total enthalpy:

:$h^t \equiv e + \frac p \rho + \frac 1 2 u^2$

and the Bernoulli invariant for an inviscid gas flow is:

:$b_g \equiv h^t + \phi = b_l + e ,$

which can be written as:

:$\mathbf u \cdot \nabla b_g = 0$

That is, the energy balance for a steady inviscid flow in an external conservative field states that the sum of the total enthalpy and the external potential is constant along a streamline.

In the usual case of small potential field, simply:

:$\mathbf u \cdot \nabla h^t \sim 0$

Friedmann form and Crocco form

By substituting the pressure gradient with the entropy and enthalpy gradient, according to the first law of thermodynamics in the enthalpy form:

:$v \nabla p = -T \nabla s + \nabla h$

in the convective form of Euler momentum equation, one arrives to:

:$\frac{D\mathbf u}{Dt}=T \nabla\,s-\nabla \,h$

Friedmann deduced this equation for the particular case of a perfect gas and published it in 1922. However, this equation is general for an inviscid nonconductive fluid and no equation of state is implicit in it.

On the other hand, by substituting the enthalpy form of the first law of thermodynamics in the rotational form of Euler momentum equation, one obtains:

:$\frac{\partial\mathbf{u{\partial t} + \frac{1}{2} \nabla\left(u^2\right) + (\nabla \times \mathbf{u}) \times \mathbf{u} + \frac{\nabla p}{\rho} = \mathbf{g}$

and by defining the specific total enthalpy:

:$h^t = h + \frac{1}{2}u^2$

one arrives to the Crocco–Vazsonyi form (Crocco, 1937) of the Euler momentum equation:

:$\frac{\partial \mathbf{ u{\partial t} + (\nabla \times \mathbf u) \times \mathbf u - T \nabla s + \nabla h^t = \mathbf{g}$

In the steady case the two variables entropy and total enthalpy are particularly useful since Euler equations can be recast into the Crocco's form:

:$\left\{\begin{align} \mathbf{u} \times \nabla \times \mathbf{u} + T\nabla s - \nabla h^t &= \mathbf{g} \\ \mathbf{u} \cdot \nabla s &= 0 \\ \mathbf{u} \cdot \nabla h^t &= 0 \end{align}\right.$

Finally if the flow is also isothermal:

:$T \nabla s = \nabla (T s)$

by defining the specific total Gibbs free energy:

:$g^t \equiv h^t + Ts$

the Crocco's form can be reduced to:

:$\left\{\begin{align} \mathbf{u} \times \nabla \times \mathbf{u} - \nabla g^t &= \mathbf{g} \\ \mathbf{u} \cdot \nabla g^t &= 0 \end{align}\right.$

From these relationships one deduces that the specific total free energy is uniform in a steady, irrotational, isothermal, isoentropic, inviscid flow.

Discontinuities

The Euler equations are quasilinear hyperbolic equations and their general solutions are waves. Under certain assumptions they can be simplified leading to Burgers equation. Much like the familiar oceanic waves, waves described by the Euler Equations 'break' and so-called shock waves are formed; this is a nonlinear effect and represents the solution becoming multi-valued. Physically this represents a breakdown of the assumptions that led to the formulation of the differential equations, and to extract further information from the equations we must go back to the more fundamental integral form. Then, weak solutions are formulated by working in 'jumps' (discontinuities) into the flow quantities – density, velocity, pressure, entropy – using the Rankine–Hugoniot equations. Physical quantities are rarely discontinuous; in real flows, these discontinuities are smoothed out by viscosity and by heat transfer. (See Navier–Stokes equations)

Shock propagation is studied – among many other fields – in aerodynamics and rocket propulsion, where sufficiently fast flows occur.

To properly compute the continuum quantities in discontinuous zones (for example shock waves or boundary layers) from the ''local'' forms (all the above forms are local forms, since the variables being described are typical of one point in the space considered, i.e. they are ''local variables'') of Euler equations through finite difference methods generally too many space points and time steps would be necessary for the memory of computers now and in the near future. In these cases it is mandatory to avoid the local forms of the conservation equations, passing some weak forms, like the finite volume one.

Rankine–Hugoniot equations

Starting from the simplest case, one consider a steady free conservation equation in conservation form in the space domain:

:$\nabla \cdot \mathbf F = \mathbf 0$

where in general F is the flux matrix. By integrating this local equation over a fixed volume V_m, it becomes:

:$\int_{V_m} \nabla \cdot \mathbf F \,dV = \mathbf 0.$

Then, basing on the divergence theorem, we can transform this integral in a boundary integral of the flux:

:$\oint_{\partial V_m} \mathbf F \,ds = \mathbf 0.$

This ''global form'' simply states that there is no net flux of a conserved quantity passing through a region in the case steady and without source. In 1D the volume reduces to an interval, its boundary being its extrema, then the divergence theorem reduces to the fundamental theorem of calculus:

:$\int_{x_m}^{x_{m+1 \mathbf F(x') \,dx' = \mathbf 0,$

that is the simple finite difference equation, known as the ''jump relation'':

:$\Delta \mathbf F = \mathbf 0.$

That can be made explicit as:

:$\mathbf F_{m+1} - \mathbf F_m = \mathbf 0$

where the notation employed is:

:$\mathbf F_{m} = \mathbf F(x_m).$

Or, if one performs an indefinite integral:

:$\mathbf F - \mathbf F_0 = \mathbf 0.$

On the other hand, a transient conservation equation:

:${\partial y \over \partial t} + \nabla \cdot \mathbf F = \mathbf 0$

brings to a jump relation:

:$\frac{dx}{dt} \, \Delta u = \Delta \mathbf F.$

For one-dimensional Euler equations the conservation variables and the flux are the vectors:

:$\mathbf y = \begin{pmatrix} \frac{1}{v} \\ j \\ E^t \end{pmatrix},$
:$\mathbf F = \begin{pmatrix} j \\ v j^2 + p \\ v j \left(E^t + p\right) \end{pmatrix},$

where:
* $v$ is the specific volume,
* $j$ is the mass flux.

In the one dimensional case the correspondent jump relations, called the Rankine–Hugoniot equations, are:<

: \left\{\begin{align}
\frac{dx}{dt}\Delta \left(\frac{1}{v}\right) &= \Delta j\\ .2ex \frac{dx}{dt}\Delta j &= \Delta(vj^2 + p)\\ .2ex \frac{dx}{dt}\Delta E^t &= \Delta(jv(E^t + p))
\end{align}\right. .

In the steady one dimensional case the become simply:

: \left\{\begin{align}
\Delta j &= 0\\ .2ex \Delta\left(v j^2 + p\right) &= 0 \\ .2ex \Delta\left(j\left(\frac{E^t}{\rho} + \frac{p}{\rho}\right)\right) &= 0
\end{align}\right. .

Thanks to the mass difference equation, the energy difference equation can be simplified without any restriction:

:\left\{\begin{align}
\Delta j &= 0 \\ .2ex \Delta\left(vj^2 + p\right) &= 0 \\ .2ex \Delta h^t &= 0
\end{align}\right.,

where $h^t$ is the specific total enthalpy.

These are the usually expressed in the convective variables:

:\left\{\begin{align}
\Delta j &= 0 \\ .2ex \Delta\left(\frac{u^2}{v} + p\right) &= 0 \\ .2ex \Delta\left(e + \frac{1}{2}u^2 + pv\right) &= 0
\end{align}\right.,

where:
* $u$ is the flow speed
* $e$ is the specific internal energy.

The energy equation is an integral form of the Bernoulli equation in the compressible case.
The former mass and momentum equations by substitution lead to the Rayleigh equation:

: $\frac{\Delta p}{\Delta v} = - \frac {u_0^2}{v_0}.$

Since the second term is a constant, the Rayleigh equation always describes a simple line in the pressure volume plane not dependent of any equation of state, i.e. the Rayleigh line. By substitution in the Rankine–Hugoniot equations, that can be also made explicit as:

: \left\{\begin{align}
\rho u &= \rho_0 u_0 \\ .2ex \rho u^2 + p &= \rho_0 u_0^2 + p_0 \\ .2ex e + \frac{1}{2}u^2 + \frac{p}{\rho} &= e_0 + \frac{1}{2}u_0^2 + \frac{p_0}{\rho_0}
\end{align}\right. .

One can also obtain the kinetic equation and to the Hugoniot equation. The analytical passages are not shown here for brevity.

These are respectively:

: \left\{\begin{align}
u^2(v, p) &= u_0^2 + (p - p_0)(v_0 + v) \\ .2ex e(v, p) &= e_0 + \frac{1}{2} (p + p_0)(v_0 - v)
\end{align}\right. .

The Hugoniot equation, coupled with the fundamental equation of state of the material:

:$e = e(v,p)$

describes in general in the pressure volume plane a curve passing by the conditions (v₀, p₀), i.e. the Hugoniot curve, whose shape strongly depends on the type of material considered.

It is also customary to define a ''Hugoniot function'':

: $\mathfrak h (v,s) \equiv e(v,s) - e_0 + \frac{1}{2} (p(v,s) + p_0)(v - v_0)$

allowing to quantify deviations from the Hugoniot equation, similarly to the previous definition of the ''hydraulic head'', useful for the deviations from the Bernoulli equation.

Finite volume form

On the other hand, by integrating a generic conservation equation:

:$\frac {\partial \mathbf y}{\partial t} + \nabla \cdot \mathbf F = \mathbf s$

on a fixed volume V_m, and then basing on the divergence theorem, it becomes:

:$\frac {d}{dt} \int_{V_m} \mathbf y dV + \oint_{\partial V_m} \mathbf F \cdot \hat n ds = \mathbf S .$

By integrating this equation also over a time interval:

: $\int_{V_m} \mathbf y(\mathbf r, t_{n+1}) \, dV - \int_{V_m} \mathbf y(\mathbf r, t_n) \, dV+ \int_{t_n}^{t_{n+1 \oint_{\partial V_m} \mathbf F \cdot \hat n \, ds \, dt = \mathbf 0 .$

Now by defining the node conserved quantity:

: $\mathbf y_{m,n} \equiv \frac 1 {V_m} \int_{V_m} \mathbf y(\mathbf r, t_n) \, dV ,$

we deduce the finite volume form:

: $\mathbf{y}_{m,n+1}=\mathbf{y}_{m,n} - \frac{1}{V_m} \int_{t_n}^{t_{n+1 \oint_{\partial V_m} \mathbf{F} \cdot \hat{n}\, ds \, dt .$

In particular, for Euler equations, once the conserved quantities have been determined, the convective variables are deduced by back substitution:

: \left\{\begin{align}
\mathbf u_{m,n} &= \frac{\mathbf j_{m,n{\rho_{m,n \\ .2ex e_{m,n} &= \frac{E^t_{m,n{\rho_{m,n - \frac{1}{2}u^2_{m,n} \\ .2ex\end{align}\right. .

Then the explicit finite volume expressions of the original convective variables are:<

\oint_{\partial V_m}\rho\mathbf{u} \cdot \hat{n}\, ds\, dt \\ .2ex \mathbf u_{m,n+1} &= \mathbf u_{m,n} - \frac{1}{\rho_{m,n} V_m}\int_{t_n}^{t_{n+1\oint_{\partial V_m} (\rho\mathbf{u} \otimes \mathbf{u} - p\mathbf{I}) \cdot \hat{n}\, ds\, dt \\ .2ex \mathbf e_{m,n+1} &= \mathbf e_{m,n} - \frac{1}{2}\left(u^2_{m,n+1} - u^2_{m,n}\right) - \frac{1}{\rho_{m,n} V_m}\int_{t_n}^{t_{n+1\oint_{\partial V_m} \left(\rho e + \frac{1}{2}\rho u^2 + p\right)\mathbf{u} \cdot \hat{n}\, ds\, dt \\ .2ex\end{align}\right. .
, cellpadding
, border
, border colour = #FF0000
, background colour = #ECFCF4

Constraints

It has been shown that Euler equations are not a complete set of equations, but they require some additional constraints to admit a unique solution: these are the equation of state of the material considered. To be consistent with thermodynamics these equations of state should satisfy the two laws of thermodynamics. On the other hand, by definition non-equilibrium system are described by laws lying outside these laws. In the following we list some very simple equations of state and the corresponding influence on Euler equations.

Ideal polytropic gas

For an ideal polytropic gas the fundamental equation of state is:

:$e(v, s) = e_0 e^{(\gamma-1)m\left(s-s_0\right)} \left({v_0 \over v}\right)^{\gamma-1}$

where $e$ is the specific energy, $v$ is the specific volume, $s$ is the specific entropy, $m$ is the molecular mass, $\gamma$ here is considered a constant ( polytropic process), and can be shown to correspond to the heat capacity ratio. This equation can be shown to be consistent with the usual equations of state employed by thermodynamics.

From this equation one can derive the equation for pressure by its thermodynamic definition:

:$p(v,e) \equiv - {\partial e \over \partial v} = (\gamma - 1) \frac e v$

By inverting it one arrives to the mechanical equation of state:

:$e(v,p) = \frac {pv}{\gamma - 1}$

Then for an ideal gas the compressible Euler equations can be simply expressed in the ''mechanical'' or ''primitive variables'' specific volume, flow velocity and pressure, by taking the set of the equations for a thermodynamic system and modifying the energy equation into a pressure equation through this mechanical equation of state. At last, in convective form they result:

{Dt} &= v\nabla p + \mathbf{g} \\ .2ex {Dp \over Dt} &= -\gamma p\nabla \cdot \mathbf{u}
\end{align}\right.
, cellpadding
, border
, border colour = #FF00FF
, background colour = #ECFCF4

and in one-dimensional quasilinear form they results:

:$\frac{\partial \mathbf y}{\partial t} + \mathbf A \frac{\partial \mathbf y}{\partial x} = {\mathbf 0}.$

where the conservative vector variable is:

:${\mathbf y}=\begin{pmatrix}v\\ u \\p \end{pmatrix}$

and the corresponding jacobian matrix is:

: ${\mathbf A}=\begin{pmatrix}u & -v & 0 \\ 0 & u & v \\ 0 & \gamma p & u \end{pmatrix}.$

Steady flow in material coordinates

In the case of steady flow, it is convenient to choose the Frenet–Serret frame along a streamline as the coordinate system for describing the steady momentum Euler equation:
:$\boldsymbol{u}\cdot\nabla \boldsymbol{u} = - \frac{1}{\rho} \nabla p,$

where $\mathbf u$, $p$ and $\rho$ denote the flow velocity, the pressure and the density, respectively.

Let $\left\{ \mathbf e_s, \mathbf e_n, \mathbf e_b \right\}$ be a Frenet–Serret orthonormal basis which consists of a tangential unit vector, a normal unit vector, and a binormal unit vector to the streamline, respectively. Since a streamline is a curve that is tangent to the velocity vector of the flow, the left-hand side of the above equation, the convective derivative of velocity, can be described as follows:
:$\begin{align} \boldsymbol{u}\cdot\nabla \boldsymbol{u} \\ &= u\frac{\partial}{\partial s}(u\boldsymbol{e}_s) &(\boldsymbol{u} = u \boldsymbol{e}_s,~ {\partial / \partial s} \equiv \boldsymbol{e}_s \cdot \nabla) \\ &= u\frac{\partial u}{\partial s}\boldsymbol{e}_s + \frac{u^2}{R}\boldsymbol{e}_n &(\because~ \frac{\partial\boldsymbol{e}_s}{\partial s} = \frac{1}{R}\boldsymbol{e}_n), \end{align}$

where $R$ is the radius of curvature of the streamline.

Therefore, the momentum part of the Euler equations for a steady flow is found to have a simple form:
:$\begin{cases} \displaystyle u\frac{\partial u}{\partial s} = -\frac{1}{\rho}\frac{\partial p}{\partial s},\\ \displaystyle {u^2 \over R} = -\frac{1}{\rho}\frac{\partial p}{\partial n} &({\partial / \partial n}\equiv\boldsymbol{e}_n\cdot\nabla),\\ \displaystyle 0 = -\frac{1}{\rho}\frac{\partial p}{\partial b} &({\partial / \partial b}\equiv\boldsymbol{e}_b\cdot\nabla). \end{cases}$

For barotropic flow $(\rho = \rho(p))$, Bernoulli's equation is derived from the first equation:
:$\frac{\partial}{\partial s}\left(\frac{u^2}{2} + \int\frac{\mathrm{d}p}{\rho}\right) = 0.$

The second equation expresses that, in the case the streamline is curved, there should exist a pressure gradient normal to the streamline because the centripetal acceleration of the fluid parcel is only generated by the normal pressure gradient.

The third equation expresses that pressure is constant along the binormal axis.

Streamline curvature theorem

Let $r$ be the distance from the center of curvature of the streamline, then the second equation is written as follows:
:$\frac{\partial p}{\partial r} = \rho \frac{u^2}{r}~(>0),$

where ${\partial / \partial r} = -{\partial /\partial n}.$

This equation states:

''
In a steady flow of an inviscid fluid without external forces, the center of curvature of the streamline lies in the direction of decreasing radial pressure.
''

Although this relationship between the pressure field and flow curvature is very useful, it doesn't have a name in the English-language scientific literature. Japanese fluid-dynamicists call the relationship the "Streamline curvature theorem".

This "theorem" explains clearly why there are such low pressures in the centre of vortices, which consist of concentric circles of streamlines.
This also is a way to intuitively explain why airfoils generate lift forces.

Exact solutions

All potential flow solutions are also solutions of the Euler equations, and in particular the incompressible Euler equations when the potential is harmonic.

Solutions to the Euler equations with vorticity are:
* parallel shear flows – where the flow is unidirectional, and the flow velocity only varies in the cross-flow directions, e.g. in a Cartesian coordinate system $(x,y,z)$ the flow is for instance in the $x$-direction – with the only non-zero velocity component being $u_x(y,z)$ only dependent on $y$ and $z$ and not on $x.$
* Arnold–Beltrami–Childress flow – an exact solution of the incompressible Euler equations.
* Two solutions of the three-dimensional Euler equations with cylindrical symmetry have been presented by Gibbon, Moore and Stuart in 2003. These two solutions have infinite energy; they blow up everywhere in space in finite time.

See also

* Bernoulli's theorem
* Kelvin's circulation theorem
* Cauchy equations
* Froude number
* Madelung equations
* Navier–Stokes equations
* Burgers equation
* Jeans equations
* Perfect fluid

References

Notes

Citations

Sources

*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*

Further reading

*
*
*

{{Authority control

Equations of physics
Equations of fluid dynamics
Leonhard Euler