Electron-beam-induced deposition (EBID) is a process of decomposing gaseous molecules by an electron beam leading to deposition of non-volatile fragments onto a nearby substrate. The electron beam is usually provided by a scanning electron microscope, which results in high spatial accuracy (potentially below one nanometer) and the possibility to produce free-standing, three-dimensional structures.

Process

Electron beam-induced deposition (schematic)

The focused electron beam of a scanning electron microscope (SEM) or scanning transmission electron microscope (STEM) is commonly used. Another method is ion-beam-induced deposition (IBID), where a focused ion beam is applied instead. Precursor materials are typically liquid or solid and gasified prior to deposition, usually through vaporization or sublimation, and introduced, at accurately controlled rate, into the high-vacuum chamber of the electron microscope. Alternatively, solid precursors can be sublimated by the electron beam itself. When deposition occurs at a high temperature or involves corrosive gases, a specially designed deposition chamber is used; it is isolated from the microscope, and the beam is introduced into it through a micrometre-sized orifice. The small orifice size maintains differential pressure in the microscope (vacuum) and deposition chamber (no vacuum). Such deposition mode has been used for EBID of diamond. In the presence of the precursor gas, the electron beam is scanned over the substrate, resulting in deposition of material. The scanning is usually computer-controlled. The deposition rate depends on a variety of processing parameters, such as the partial precursor pressure, substrate temperature, electron beam parameters, applied current density, etc. It usually is in the order of 10 nm/s.

Deposition mechanism

Primary electron energies in SEMs or STEMs are usually between 10 and 300 keV, where reactions induced by electron impact, i.e. precursor dissociation, have a relatively low cross section. The majority of decomposition occurs via low energy electron impact: either by low energy secondary electrons, which cross the substrate-vacuum interface and contribute to the total current density, or inelastically scattered (backscattered) electrons.

Spatial resolution

Primary S(T)EM electrons can be focused into spots as small as ~0.045 nm. While the smallest structures deposited so far by EBID are point deposits of ~0.7 nm diameter., deposits usually have a larger lateral size than the beam spot size. The reason are the so-called proximity effects, meaning that secondary, backscattered and forward scattered (if the beam dwells on already deposited material) electrons contribute to the deposition. As these electrons can leave the substrate up to several microns away from the point of impact of the electron beam (depending on its energy), material deposition is not necessarily confined to the irradiated spot. To overcome this problem, compensation algorithms can be applied, which is typical for electron beam lithography.

Materials and precursors

As of 2008 the range of materials deposited by EBID included Al, Au, amorphous carbon, diamond, Co, Cr, Cu, Fe, GaAs, GaN, Ge, Mo, Nb, Ni, Os, Pd, Pt, Rh, Ru, Re, Si, Si₃N₄, SiO_x, TiO_x, W, and was being expanded. The limiting factor is the availability of appropriate precursors, gaseous or having a low sublimation temperature. The most popular precursors for deposition of elemental solids are

metal carbonyl Metal carbonyls are coordination complexes of transition metals with carbon monoxide ligands. Metal carbonyls are useful in organic synthesis and as catalysts or catalyst precursors in homogeneous catalysis, such as hydroformylation and Reppe c ...

s of Me(CO)_x structure or metallocenes. They are easily available, however, due to incorporation of carbon atoms from the CO ligands, deposits often exhibit a low metal content. Metal-halogen complexes ( WF₆, etc.) result in cleaner deposition, but are more difficult to handle as they are toxic and corrosive. Compound materials are deposited from specially crafted, exotic gases, e.g. D₂GaN₃ for GaN.

Advantages

*Very flexible regarding deposit shape and composition; the electron beam is lithographically controlled and a multitude of potential precursors is available *Lateral size of the produced structures and accuracy of deposition are unprecedented *The deposited material can be characterized using the electron microscopy techniques ( TEM,

EELS Eels are ray-finned fish belonging to the order Anguilliformes (), which consists of eight suborders, 19 families, 111 genera, and about 800 species. Eels undergo considerable development from the early larval stage to the eventual adult stage ...

, EDS,

electron diffraction Electron diffraction refers to the bending of electron beams around atomic structures. This behaviour, typical for waves, is applicable to electrons due to the wave–particle duality stating that electrons behave as both particles and waves. S ...

) during or right after deposition. In situ electrical and optical characterization is also possible.

Disadvantages

*Serial material deposition and low deposition rates in general limit throughput and thus mass production *Controlling the elemental or chemical deposit composition is still a major challenge, as the precursor decomposition pathways are mostly unknown *Proximity effects can lead to unintended structure broadening

Ion-beam-induced deposition

Ion-beam-induced deposition (IBID) is very similar to EBID with the major difference that focused ion beam, usually 30 keV Ga⁺, is used instead of the electron beam. In both techniques, it is not the primary beam, but secondary electrons which cause the deposition. IBID has the following disadvantages as compared to EBID: *Angular spread of secondary electrons is larger in IBID thus resulting in lower spatial resolution. *Ga⁺ ions introduce additional contamination and radiation damage to the deposited structure, which is important for electronic applications. *Deposition occurs in a focused ion beam (FIB) setup, which strongly limits characterization of the deposit during or right after the deposition. Only SEM-like imaging using secondary electrons is possible, and even that imaging is restricted to short observations due to sample damaging by the Ga⁺ beam. The use of a dual beam instrument, that combines a FIB and an SEM in one, circumvents this limitation. The advantages of IBID are: *Much higher deposition rate *Higher purity

Shapes

Nanostructures of virtually any 3-dimensional shape can be deposited using computer-controlled scanning of electron beam. Only the starting point has to be attached to the substrate, the rest of the structure can be free standing. The achieved shapes and devices are remarkable: *World smallest magnet *Fractal nanotrees *Nanoloops (potential nano

SQUID True squid are molluscs with an elongated soft body, large eyes, eight arms, and two tentacles in the superorder Decapodiformes, though many other molluscs within the broader Neocoleoidea are also called squid despite not strictly fittin ...

device) *Superconducting nanowires IBID human growth.jpg, Snapshots of growing a doll-like nanostructure by IBID IBID bacteriophage.jpg, A model of

bacteriophage A bacteriophage (), also known informally as a ''phage'' (), is a duplodnaviria virus that infects and replicates within bacteria and archaea. The term was derived from "bacteria" and the Greek φαγεῖν ('), meaning "to devour". Bac ...

grown by IBID IBID tower.jpg, A model of

Leaning Tower of Pisa The Leaning Tower of Pisa ( it, torre pendente di Pisa), or simply, the Tower of Pisa (''torre di Pisa'' ), is the ''campanile'', or freestanding bell tower, of Pisa Cathedral. It is known for its nearly four-degree lean, the result of an unst ...

grown by IBID EBIDloop.JPG, Letter Φ grown by EBID

References

External links

* "Nanofabrication: Fundamentals and Applications" Ed.: Ampere A. Tseng, World Scientific Publishing Company (March 4, 2008), , {{ISBN, 978-981-270-076-6
K. Molhave: "Tools for in-situ manipulations and characterization of nanostructures", PhD thesis, Technical University of Denmark, 2004
Electron beam Electron microscopy Nanotechnology