HOME

TheInfoList



OR:

Double Data Rate 4 Synchronous Dynamic Random-Access Memory (DDR4 SDRAM) is a type of synchronous dynamic random-access memory with a high
bandwidth Bandwidth commonly refers to: * Bandwidth (signal processing) or ''analog bandwidth'', ''frequency bandwidth'', or ''radio bandwidth'', a measure of the width of a frequency range * Bandwidth (computing), the rate of data transfer, bit rate or thr ...
(" double data rate") interface. Released to the market in 2014, it is a variant of dynamic random-access memory (DRAM), of which some have been in use since the early 1970s, and a higher-speed successor to the DDR2 and DDR3 technologies. DDR4 is not compatible with any earlier type of random-access memory (RAM) due to different signaling voltage and physical interface, besides other factors. DDR4 SDRAM was released to the public market in Q2 2014, focusing on
ECC memory Error correction code memory (ECC memory) is a type of computer data storage that uses an error correction code (ECC) to detect and correct n-bit data corruption which occurs in memory. ECC memory is used in most computers where data corruption c ...
, while the non-ECC DDR4 modules became available in Q3 2014, accompanying the launch of Haswell-E processors that require DDR4 memory.


Features

The primary advantages of DDR4 over its predecessor, DDR3, include higher module density and lower voltage requirements, coupled with higher data rate transfer speeds. The DDR4 standard allows for
DIMM A DIMM () (Dual In-line Memory Module), commonly called a RAM stick, comprises a series of dynamic random-access memory integrated circuits. These memory modules are mounted on a printed circuit board and designed for use in personal computers ...
s of up to 64  GB in capacity, compared to DDR3's maximum of 16 GB per DIMM. Unlike previous generations of DDR memory, prefetch has ''not'' been increased above the 8n used in DDR3; the basic burst size is eight 64-bit words, and higher bandwidths are achieved by sending more read/write commands per second. To allow this, the standard divides the DRAM banks into two or four selectable bank groups, where transfers to different bank groups may be done more rapidly. Because power consumption increases with speed, the reduced voltage allows higher speed operation without unreasonable power and cooling requirements. DDR4 operates at a voltage of 1.2 V with a frequency between 800 and 1600 MHz (DDR4-1600 through DDR4-3200), compared to frequencies between 400 and 1067 MHz (DDR3-800 through DDR3-2133) and voltage requirements of 1.5 V of DDR3. Due to the nature of DDR, speeds are typically advertised as doubles of these numbers (DDR3-1600 and DDR4-2400 are common, with DDR4-3200, DDR4-4800 and DDR4-5000 available at high cost). Unlike DDR3's 1.35 V low voltage standard
DDR3L Double Data Rate 3 Synchronous Dynamic Random-Access Memory (DDR3 SDRAM) is a type of synchronous dynamic random-access memory (SDRAM) with a high bandwidth ("double data rate") interface, and has been in use since 2007. It is the higher-speed ...
, there is no DDR4L low voltage version of DDR4.


Timeline

* 2005: Standards body JEDEC began working on a successor to DDR3 around 2005, about 2 years before the launch of DDR3 in 2007. The high-level architecture of DDR4 was planned for completion in 2008. * 2007: Some advance information was published in 2007, and a guest speaker from Qimonda provided further public details in a presentation at the August 2008
San Francisco San Francisco (; Spanish for " Saint Francis"), officially the City and County of San Francisco, is the commercial, financial, and cultural center of Northern California. The city proper is the fourth most populous in California and 17th ...
Intel Developer Forum (IDF).
English
DDR4 was described as involving a 30 nm process at 1.2 volts, with
bus A bus (contracted from omnibus, with variants multibus, motorbus, autobus, etc.) is a road vehicle that carries significantly more passengers than an average car or van. It is most commonly used in public transport, but is also in use for cha ...
frequencies of 2133
MT/s In computer technology, transfers per second and its more common secondary terms gigatransfers per second (abbreviated as GT/s) and megatransfers per second (MT/s) are informal language that refer to the number of operations transferring data that ...
"regular" speed and 3200 MT/s "enthusiast" speed, and reaching market in 2012, before transitioning to 1 volt in 2013. * 2009: In February,
Samsung The Samsung Group (or simply Samsung) ( ko, 삼성 ) is a South Korean multinational manufacturing conglomerate headquartered in Samsung Town, Seoul, South Korea. It comprises numerous affiliated businesses, most of them united under the ...
validated 40 nm DRAM chips, considered a "significant step" towards DDR4 development since in 2009, DRAM chips were only beginning to migrate to a 50 nm process. * 2010: Subsequently, further details were revealed at MemCon 2010,
Tokyo Tokyo (; ja, 東京, , ), officially the Tokyo Metropolis ( ja, 東京都, label=none, ), is the capital and List of cities in Japan, largest city of Japan. Formerly known as Edo, its metropolitan area () is the most populous in the world, ...
(a computer memory industry event), at which a presentation by a JEDEC director titled "Time to rethink DDR4" with a slide titled "New roadmap: More realistic roadmap is 2015" led some websites to report that the introduction of DDR4 was probably or definitely delayed until 2015. However, DDR4 test samples were announced in line with the original schedule in early 2011 at which time manufacturers began to advise that large scale commercial production and release to market was scheduled for 2012. * 2011: In January,
Samsung The Samsung Group (or simply Samsung) ( ko, 삼성 ) is a South Korean multinational manufacturing conglomerate headquartered in Samsung Town, Seoul, South Korea. It comprises numerous affiliated businesses, most of them united under the ...
announced the completion and release for testing of a 2 GB DDR4 DRAM module based on a process between 30 and 39 nm. It has a maximum data transfer rate of 2133 
MT/s In computer technology, transfers per second and its more common secondary terms gigatransfers per second (abbreviated as GT/s) and megatransfers per second (MT/s) are informal language that refer to the number of operations transferring data that ...
at 1.2 V, uses pseudo open drain technology (adapted from graphics DDR memory) and draws 40% less power than an equivalent DDR3 module.
In April, Hynix announced the production of 2 GB DDR4 modules at 2400 MT/s, also running at 1.2 V on a process between 30 and 39 nm (exact process unspecified), adding that it anticipated commencing high volume production in the second half of 2012. Semiconductor processes for DDR4 are expected to transition to sub-30 nm at some point between late 2012 and 2014. * 2012: In May,
Micron The micrometre ( international spelling as used by the International Bureau of Weights and Measures; SI symbol: μm) or micrometer (American spelling), also commonly known as a micron, is a unit of length in the International System of Un ...
announced it is aiming at starting production in late 2012 of 30 nm modules.
In July, Samsung announced that it would begin sampling the industry's first 16 GB registered dual inline memory modules (RDIMMs) using DDR4 SDRAM for enterprise server systems.
In September, JEDEC released the final specification of DDR4. * 2013: DDR4 was expected to represent 5% of the DRAM market in 2013, and to reach
mass market The term "mass market" refers to a market for goods produced on a large scale for a significant number of end consumers. The mass market differs from the niche market in that the former focuses on consumers with a wide variety of backgrounds wi ...
adoption and 50% market penetration around 2015; as of 2013, however, adoption of DDR4 had been delayed and it was no longer expected to reach a majority of the market until 2016 or later.. The transition from DDR3 to DDR4 is thus taking longer than the approximately five years taken for DDR3 to achieve mass market transition over DDR2.
English translation
In part, this is because changes required to other components would affect all other parts of computer systems, which would need to be updated to work with DDR4. * 2014: In April, Hynix announced that it had developed the world's first highest-density 128 GB module based on 8  Gbit DDR4 using 20 nm technology. The module works at 2133 MHz, with a 64-bit I/O, and processes up to 17 GB of data per second. * 2016: In April, Samsung announced that they had begun to mass-produce DRAM on a "10 nm-class" process, by which they mean the 1x nm node regime of 16 nm to 19 nm, which supports a 30% faster data transfer rate of 3,200 Mbit/s. Previously, a size of 20 nm was used.


Market perception and adoption

In April 2013, a news writer at International Data Group (IDG)an American technology research business originally part of IDCproduced an analysis of their perceptions related to DDR4 SDRAM. The conclusions were that the increasing popularity of mobile computing and other devices using slower but low-powered memory, the slowing of growth in the traditional
desktop computing A desktop traditionally refers to: * The surface of a desk (often to distinguish office appliances that fit on a desk, such as photocopiers and printers, from larger equipment covering its own area on the floor) Desktop may refer to various compu ...
sector, and the consolidation of the memory manufacturing marketplace, meant that margins on RAM were tight. As a result, the desired
premium pricing Premium pricing (also called image pricing or prestige pricing) is the practice of keeping the price of one of the products or service artificially high in order to encourage favorable perceptions among buyers, based solely on the price. Premium re ...
for the new technology was harder to achieve, and capacity had shifted to other sectors. SDRAM manufacturers and chipset creators were, to an extent, "
stuck between a rock and a hard place A dilemma ( grc-gre, δίλημμα "double proposition") is a problem offering two possibilities, neither of which is unambiguously acceptable or preferable. The possibilities are termed the ''horns'' of the dilemma, a clichéd usage, but distin ...
" where "nobody wants to pay a premium for DDR4 products, and manufacturers don't want to make the memory if they are not going to get a premium", according to Mike Howard from iSuppli. A switch in consumer sentiment toward desktop computing and release of processors having DDR4 support by
Intel Intel Corporation is an American multinational corporation and technology company headquartered in Santa Clara, California. It is the world's largest semiconductor chip manufacturer by revenue, and is one of the developers of the x86 seri ...
and
AMD Advanced Micro Devices, Inc. (AMD) is an American multinational semiconductor company based in Santa Clara, California, that develops computer processors and related technologies for business and consumer markets. While it initially manufactur ...
could therefore potentially lead to "aggressive" growth. Intel's 2014 Haswell roadmap, revealed the company's first use of DDR4 SDRAM in Haswell-EP processors. AMD's
Ryzen Ryzen ( ) is a brand of multi-core x86-64 microprocessors designed and marketed by AMD for desktop, mobile, server, and embedded platforms based on the Zen microarchitecture. It consists of central processing units (CPUs) marketed for mainst ...
processors, revealed in 2016 and shipped in 2017, use DDR4 SDRAM.


Operation

DDR4 chips use a 1.2  V supply with a 2.5 V auxiliary supply for wordline boost called VPP, as compared with the standard 1.5 V of DDR3 chips, with lower voltage variants at 1.35 V appearing in 2013. DDR4 is expected to be introduced at transfer rates of 2133 MT/s, estimated to rise to a potential 4266 MT/s by 2013. The minimum transfer rate of 2133 MT/s was said to be due to progress made in DDR3 speeds which, being likely to reach 2133 MT/s, left little commercial benefit to specifying DDR4 below this speed. Techgage interpreted Samsung's January 2011 engineering sample as having
CAS latency Column Address Strobe (CAS) latency, or CL, is the delay in clock cycles between the READ command and the moment data is available. In asynchronous DRAM, the interval is specified in nanoseconds (absolute time). In synchronous DRAM, the interval ...
of 13 clock cycles, described as being comparable to the move from DDR2 to DDR3. Internal banks are increased to 16 (4 bank select bits), with up to 8 ranks per DIMM. Protocol changes include: * Parity on the command/address bus * Data bus inversion (like GDDR4) * CRC on the data bus * Independent programming of individual DRAMs on a DIMM, to allow better control of on-die termination. Increased memory density is anticipated, possibly using TSV ("
through-silicon via In electronic engineering, a through-silicon via (TSV) or through-chip via is a vertical electrical connection (via) that passes completely through a silicon wafer or die. TSVs are high-performance interconnect techniques used as an alternative ...
") or other 3D stacking processes.
Page 1 2 3
The DDR4 specification will include standardized 3D stacking "from the start" according to JEDEC, with provision for up to dies. X-bit Labs predicted that "as a result DDR4 memory chips with very high density will become relatively inexpensive". Switched memory banks are also an anticipated option for servers. In 2008 concerns were raised in the book ''Wafer Level 3-D ICs Process Technology'' that non-scaling analog elements such as
charge pump A charge pump is a kind of DC-to-DC converter that uses capacitors for energetic charge storage to raise or lower voltage. Charge-pump circuits are capable of high efficiencies, sometimes as high as 90–95%, while being electrically simple c ...
s and
voltage regulators A voltage regulator is a system designed to automatically maintain a constant voltage. A voltage regulator may use a simple feed-forward design or may include negative feedback. It may use an electromechanical mechanism, or electronic component ...
, and additional circuitry "have allowed significant increases in
bandwidth Bandwidth commonly refers to: * Bandwidth (signal processing) or ''analog bandwidth'', ''frequency bandwidth'', or ''radio bandwidth'', a measure of the width of a frequency range * Bandwidth (computing), the rate of data transfer, bit rate or thr ...
but they consume much more die area". Examples include CRC error-detection, on-die termination, burst hardware, programmable pipelines, low impedance, and increasing need for sense amps (attributed to a decline in bits per bitline due to low voltage). The authors noted that, as a result, the amount of die used for the memory array itself has declined over time from 70–78% for SDRAM and DDR1, to 47% for DDR2, to 38% for DDR3 and to potentially less than 30% for DDR4. The specification defined standards for ×4, ×8 and ×16 memory devices with capacities of 2, 4, 8 and 16 Gbit. In addition to bandwidth and capacity variants, DDR4 modules can optionally implement: * ECC, which is an extra data byte lane used for correcting minor errors and detecting major errors for better reliability. Modules with ECC are identified by an additional ECC in their designation. PC4-19200 ECC or PC4-19200E is a PC4-19200 module with ECC. * Be "registered" ("buffered"), which improves signal integrity (and hence potentially clock rates and physical slot capacity) by electrically buffering the signals at a cost of an extra clock of increased latency. Those modules are identified by an additional R in their designation, e.g. PC4-19200R. Typically modules with this designation are actually ECC Registered, but the 'E' of 'ECC' is not always shown. Whereas non-registered (a.k.a. unbuffered RAM) may be identified by an additional U in the designation. e.g. PC4-19200U. * Be Load reduced modules, which are designated by LR and are similar to registered/buffered memory, in a way that LRDIMM modules buffer both control and data lines while retaining the parallel nature of all signals. As such, LRDIMM memory provides larger overall maximum memory capacities, while addressing some of the performance and power consumption issues of FB memory induced by the required conversion between serial and parallel signal forms.


Command encoding

Although it still operates in fundamentally the same way, DDR4 makes one major change to the command formats used by previous SDRAM generations. A new command signal, , is low to indicate the activate (open row) command. The activate command requires more address bits than any other (18 row address bits in a 16 Gbit part), so the standard , , and active low signals are shared with high-order address bits that are not used when is high. The combination of =L and

H that previously encoded an activate command is unused. As in previous SDRAM encodings, A10 is used to select command variants: auto-precharge on read and write commands, and one bank vs. all banks for the precharge command. It also selects two variants of the ZQ calibration command. As in DDR3, A12 is used to request ''burst chop'': truncation of an 8-transfer burst after four transfers. Although the bank is still busy and unavailable for other commands until eight transfer times have elapsed, a different bank can be accessed. Also, the number of bank addresses has been increased greatly. There are four bank select bits to select up to 16 banks within each DRAM: two bank address bits (BA0, BA1), and two bank group bits (BG0, BG1). There are additional timing restrictions when accessing banks within the same bank group; it is faster to access a bank in a different bank group. In addition, there are three chip select signals (C0, C1, C2), allowing up to eight stacked chips to be placed inside a single DRAM package. These effectively act as three more bank select bits, bringing the total to seven (128 possible banks). Standard transfer rates are 1600, 1866, 2133, 2400, 2666, 2933, and 3200 MT/s. Username " cypherpunks" and password "cypherpunks" will allow download. (, , , , , , and  GHz clock frequencies, double data rate), with speeds up to DDR4-4800 (2400 MHz clock) commercially available.


Design considerations

The DDR4 team at Micron Technology identified some key points for IC and PCB design: IC design: * VrefDQ calibration (DDR4 "requires that VrefDQ calibration be performed by the controller"); * New addressing schemes ("bank grouping", to replace , , and commands, PAR and for error checking and for data bus inversion); * New power saving features (low-power auto self-refresh, temperature-controlled refresh, fine-granularity refresh, data-bus inversion, and CMD/ADDR latency). Circuit board design: * New power supplies (VDD/VDDQ at 1.2 V and wordline boost, known as VPP, at 2.5 V); * VrefDQ must be supplied internal to the DRAM while VrefCA is supplied externally from the board; * DQ pins terminate high using pseudo-open-drain I/O (this differs from the CA pins in DDR3 which are center-tapped to VTT). Rowhammer mitigation techniques include larger storage capacitors, modifying the address lines to use
address space layout randomization Address space layout randomization (ASLR) is a computer security technique involved in preventing exploitation of memory corruption vulnerabilities. In order to prevent an attacker from reliably jumping to, for example, a particular exploited f ...
and dual-voltage I/O lines that further isolate potential boundary conditions that might result in instability at high write/read speeds.


Module packaging

DDR4 memory is supplied in 288-pin
dual in-line memory module A DIMM () (Dual In-line Memory Module), commonly called a RAM stick, comprises a series of dynamic random-access memory integrated circuits. These memory modules are mounted on a printed circuit board and designed for use in personal computers, ...
s (DIMMs), similar in size to 240-pin DDR3 DIMMs. The pins are spaced more closely (0.85 mm instead of 1.0) to fit the increased number within the same 5¼ inch () standard DIMM length, but the height is increased slightly ( instead of ) to make signal routing easier, and the thickness is also increased (to 1.2 mm from 1.0) to accommodate more signal layers. DDR4 DIMM modules have a slightly curved edge connector so not all of the pins are engaged at the same time during module insertion, lowering the insertion force. DDR4
SO-DIMM A DIMM () (Dual In-line Memory Module), commonly called a RAM stick, comprises a series of dynamic random-access memory integrated circuits. These memory modules are mounted on a printed circuit board and designed for use in personal computers ...
s have 260 pins instead of the 204 pins of DDR3 SO-DIMMs, spaced at 0.5 rather than 0.6 mm, and are 2.0 mm wider (69.6 versus 67.6 mm), but remain the same 30 mm in height. For its Skylake microarchitecture, Intel designed a SO-DIMM package named UniDIMM, which can be populated with either DDR3 or DDR4 chips. At the same time, the integrated memory controller (IMC) of Skylake CPUs is announced to be capable of working with either type of memory. The purpose of UniDIMMs is to help in the market transition from DDR3 to DDR4, where pricing and availability may make it undesirable to switch the RAM type. UniDIMMs have the same dimensions and number of pins as regular DDR4 SO-DIMMs, but the edge connector's notch is placed differently to avoid accidental use in incompatible DDR4 SO-DIMM sockets.


Modules


JEDEC standard DDR4 module

;
CAS latency Column Address Strobe (CAS) latency, or CL, is the delay in clock cycles between the READ command and the moment data is available. In asynchronous DRAM, the interval is specified in nanoseconds (absolute time). In synchronous DRAM, the interval ...
(CL):
Clock cycles In electronics and especially synchronous digital circuits, a clock signal (historically also known as ''logic beat'') oscillates between a high and a low state and is used like a metronome to coordinate actions of digital circuits. A clock signa ...
between sending a column address to the memory and the beginning of the data in response ;tRCD: Clock cycles between row activate and reads/writes ;tRP: Clock cycles between row precharge and activate DDR4-xxxx denotes per-bit data transfer rate, and is normally used to describe DDR chips. PC4-xxxxx denotes overall transfer rate, in megabytes per second, and applies only to modules (assembled DIMMs). Because DDR4 memory modules transfer data on a bus that is 8 bytes (64 data bits) wide, module peak transfer rate is calculated by taking transfers per second and multiplying by eight.


Successor

At the 2016 Intel Developer Forum, the future of DDR5 SDRAM was discussed. The specifications were finalized at the end of 2016 but no modules will be available before 2020. Other memory technologies namely HBM in version 3 and 4 aiming to replace DDR4 have also been proposed. In 2011, JEDEC published the Wide I/O 2 standard; it stacks multiple memory dies, but does that directly on top of the CPU and in the same package. This memory layout provides higher bandwidth and better power performance than DDR4 SDRAM, and allows a wide interface with short signal lengths. It primarily aims to replace various mobile DDR''X'' SDRAM standards used in high-performance embedded and mobile devices, such as smartphones. Hynix proposed similar High Bandwidth Memory (HBM), which was published as JEDEC JESD235. Both Wide I/O 2 and HBM use a very wide parallel memory interface, up to 512 bits wide for Wide I/O 2 (compared to 64 bits for DDR4), running at a lower frequency than DDR4. Wide I/O 2 is targeted at high-performance compact devices such as smartphones, where it will be integrated into the processor or system on a chip (SoC) packages. HBM is targeted at graphics memory and general computing, while HMC targets high-end servers and enterprise applications. Micron Technology's Hybrid Memory Cube (HMC) stacked memory uses a serial interface. Many other computer buses have migrated towards replacing parallel buses with serial buses, for example by the evolution of Serial ATA replacing Parallel ATA, PCI Express replacing PCI, and serial ports replacing parallel ports. In general, serial buses are easier to scale up and have fewer wires/traces, making circuit boards using them easier to design. In the longer term, experts speculate that non-volatile RAM types like PCM (
phase-change memory Phase-change memory (also known as PCM, PCME, PRAM, PCRAM, OUM (ovonic unified memory) and C-RAM or CRAM (chalcogenide RAM)) is a type of non-volatile random-access memory. PRAMs exploit the unique behaviour of chalcogenide glass. In PCM, heat pr ...
), RRAM ( resistive random-access memory), or MRAM (
magnetoresistive random-access memory Magnetoresistive random-access memory (MRAM) is a type of non-volatile random-access memory which stores data in magnetic domains. Developed in the mid-1980s, proponents have argued that magnetoresistive RAM will eventually surpass competing tec ...
) could replace DDR4 SDRAM and its successors.
GDDR5 Graphics Double Data Rate 5 Synchronous Dynamic Random-Access Memory (GDDR5 SDRAM) is a type of synchronous graphics random-access memory (SGRAM) with a high bandwidth ("double data rate") interface designed for use in graphics cards, game co ...
SGRAM is a graphics type of DDR3 synchronous graphics RAM, which was introduced before DDR4, and is not a successor to DDR4.


See also

*
Synchronous dynamic random access memory Synchronous dynamic random-access memory (synchronous dynamic RAM or SDRAM) is any DRAM where the operation of its external pin interface is coordinated by an externally supplied clock signal. DRAM integrated circuits (ICs) produced from the ea ...
main article for DDR memory types * List of device bandwidths *
Memory timings Memory timings or RAM timings describe the timing information of a memory module. Due to the inherent qualities of VLSI and microelectronics, memory chips require time to fully execute commands. Executing commands too quickly will result in data ...


Notes


References


External links

*
DDR4 SDRAM STANDARD (JESD79-4)
* . {{DRAM SDRAM de:DDR-SDRAM#DDR4-SDRAM