Duquesne-class Cruiser

The ''Duquesne''-class cruiser was a group of two heavy cruisers built for the French Navy in the mid 1920s, the first such vessels built for the French fleet. The two ships in the class were the and .

With the ratification of the Washington Naval Treaty of 1922, France could not ignore the ramifications of the cruiser article. To maintain her position of a major naval power she would have to follow the other four major naval powers with her own 10,000 ton - 8 inch gun cruiser. The only modern cruiser design Service techniques des constructions navales (STNC - Constructor's Department) had to draw on was the recently designed 8,000 ton design. The cruiser design authorized under the 1924 build program would sacrifice protection for speed while maintaining the 10,000 ton displacement restriction while mounting 8 inch guns. Two vessels would be authorized and would be known as the ''Duquesne''-class cruiser.

Initially classed as a light cruiser, both ships were reclassified on 1 July 1931 as first class cruisers. The French Navy did not have a vessel classification of heavy cruiser instead used armoured cruiser and light cruiser prior to the London Naval Treaty then first class cruiser and second class cruiser afterwards.

Design and description

Hull and protection

The design was an enlargement of the light cruiser with standard displacement raised to 10,000 tons. The hull was lengthened to a length between perpendiculars of with an overall length of and a beam of . The framing in a French hull was numbered from aft to stem, therefore frame no 1 would be the aft perpendicular frame with the frames being numbered by the distance in meters from the aft perpendicular. With the increase of the standard displacement to the draft of the ship would increase to .

The protection was minimal as in the previous ''Duguay-Trouin'' class and was minimally increased by 50 percent in the ''Duquesne'' class using the same armour layout. Protection over the magazines was with crowns, the protective deck would be . The conning tower and turrets would be . The hull was divided by 16 bulkheads into 17 watertight compartments. The walls of the transverse bulkheads at each end of the machinery spaces was increased to to limit flooding to three compartments for mine or torpedo hits. Each compartment would be watertight from keel to main deck with its own pumps and ventilation. The steering gear was protected with plates.

Machinery

To maintain the 10,000-ton limitation the STNC determined that using the same machinery at the previous class would have put the ships at 200 tons over the limit to achieve the 34 knot speed desired. The STNC therefore put the machinery out for bid. AC Bretagne came up with an eight boiler four shaft solution producing 155,000 CV for at normal displacement. The ships would be equipped with eight Guyot du Temple small tube boilers built by Indret rated at while operating at setup in four boiler rooms. The forward two rooms would feed the forward engine room and vent through the forward funnel. The midships boiler rooms would feed the aft engine room and vent through the aft funnel. Four identical single reduction gear Rateau-Bretagne stem turbines would produce the 120,000 CV (chevaux - horses)* to achieve the required speed. Two cruising turbines were fitted to the inboard shafts to achieve the at requirement. The boilers would be oil fired with a maximum load of 1,842 tons of oil giving an endurance of 5,000 nmi at 15 knots, at and at . The ships would have two centerline rudders. The first would be and the aft rudder would be twice as large at . They had a large tactical radius as with all French ships of this period.

Armament

The requirement of a main armament of eight guns housed in three or four lightly armoured turrets with magazine storage of 150 rounds per gun was made more difficult as the French had no 203 mm gun in their inventory. A new gun was designed with a simplistic constructed of a thick autofretted A tube, with a shrunk jacket and breach ring. The gun was bored to with a length of 50 calibers. The breach was sealed using a Welin-type interrupted screw breach that open upwards. The weapon was designated as the 203 mm/50 (8 in) Model 1924 naval gun. The guns were mounted in four Cruiser Two Gun Turret Model 1924 providing a separation of the axis of the guns by 74 inches. The turret was plated with two sheets of 15 mm high tensile steel plate riveted together placed on all sides and roof for armour protection of 30 mm. The mount provided an elevation from minus 5 degree to plus 45 degrees with an elevation rate of ten degrees per second. The mount could be trained to plus or minus 90 degrees from the centerline of the vessel with a train rate of six degrees per second. The guns could be loaded at any degree of train but only between minus 5 and plus ten degrees in elevation. The loading cycle started with the rammer cocked by the recoil of the guns. A dredger hoist brought the shell and two half charge bags to the breech. The rammer drove the shell into the breech with the powder being loaded by hand. The breech would close and the gun would be fired. The guns could maintain a rate of fire of four to five rounds per minute. At maximum elevation an APC 1927 shell with a two half charges totaling had a range of with a muzzle velocity of . The APC M1936 shell with two half charges totaling had a range of with a muzzle velocity of . In 1939 the APC M1936 shell had a dye bag with a specific colour for each ship. ''Duquesne'' was red, ''Tourville'' was Yellow and ''Suffren'' was green.

The Staff Requirement for the secondary armament was for four 100 mm high angle guns with 500 rounds. Due to weight restrictions this was reduced to eight 75 mm/50 (2.95 inch) model 1922 naval gun on single Model 1922 gun mounts. The mount provided an elevation of minus 10 degrees to plus 90 degrees with the loading angle for high elevation being limited to plus 75 degrees. Training angles were plus/minus 150 degrees from the beam of the vessel. The used fixed ammunition with a sliding breech and were capable of eight to fifteen rounds per minute. The medium anti-aircraft armament was augmented with eight 37 mm/50 (1.46 inch) model 1925 guns in eight Model 1925 single mounts. With an elevation only to plus 85 degrees they had a slow rate of fire, 15 to 21 rounds per minute therefore were not effective against modern aircraft when installed. These guns would be replaced with single 40 mm Bofors as the equipment became available. To complete the light AA armament it was intended to install four single 8 mm Hotchkiss machineguns on the quarterdeck just aft of the last 203 mm turret. However, it was recognized that these weapons were ineffective against aircraft of the period so they were replaced by twelve 13,2 mm (0.5 inch) Model 1929 machine guns. Two would be mounted forward on the lower bridge wings and the other four in place of the 8mm machine guns. These guns would be mounted in twin mountings. In 1943 they were replaced by 20 mm Oerlikon cannons based on the availability of the equipment.

For torpedoes the Staff Requirement was for two quadruple launchers with four spare torpedoes. Again due to weight limitations this was reduced to two triple launchers. The two launchers of a new type Model 1925T for 550 mm torpedoes were fitted to port and starboard. When in the locked position the starboard launcher faced forward and the port launcher faced aft. The tubes could be trained and fired either locally or from the armoured conning tower. The ships initially carried the 55 cm (21.65 inch) 23DT, Toulon torpedo. Nine torpedoes were carried, six in the tubes with three spares. The torpedo tubes were landed between 1943 and 1945.

Aircraft

The aircraft handling arrangements would not be an add-on affair as it had been on the ''Duguay-Trouin'' class. Initially two obsolete float planes, FBA 17 and the CAMS 37A would be carried. The aircraft would not be catapult launched but lowered on to the surface of the water to take off. The catapult was finally installed in 1929 - 1930 and the obsolete aircraft replaced by the Gordou-Lesseurre float plane. The catapult was installed between the fore funnel and the mainmast with one aircraft on the catapult and the other on the boat deck. Two aircraft would be carried until 1937 when the catapult was removed for modification. Once the modification was complete the catapult was reinstalled with a Loire 130 float plane. The aircraft and catapults would be removed for good between 1943 and 1945.

Ships

History

''Duquesne'' and ''Tourville'' during the interwar period she served in the Mediterranean Sea while taking periodic cruises to show the Flag. During the war ''Duquesne'' was on blockade duty in the mid-Atlantic whereas ''Tourville'' was in the Mediterranean Sea. Both became part of Force X at Alexandria prior to Italy's entry into the war where they were interned for three years after the French Armistice with Germany. With the German occupation of Vichy France in November 1942 thereby nullifying the Armistice of 1940 the ships of Force X joined the Free French Forces on 17 May 1943. They sailed for Dakar via the Suez Canal in July. Again assigned to blockade duty in the Mid Atlantic at Dakar; but their anti-aircraft protection was still considered inadequate to provide gunfire support for the invasion of Normandy. ''Duquesne'' was part of the French Naval Task Force formed in December 1944 to bombard pockets of German resistance on the French Atlantic coast. Post war both aided in the restoration of French Colonial rule in French Indochina until placed in reserve in 1947. ''Duquesne'' remained in reserve until condemned for disposal in 1955 whereas ''Tourville'' remained in reserve until condemned for disposal in 1962.Jordan & Moulin, Chapter 12, The Deactivation of Cruisers

Note

* all ship statistical data from ''French Cruisers 1922 - 1956'' (Jordan & Moulin, Chapter 2, Duquesne and Tourville, Design and Construction, Building Data and General Characteristics) unless otherwise noted
* French sources do not use shaft horsepower rating for the power output of their machinery. Instead the term 'chevaux' (CV) or horses is used. To convert the French measure to SHP multiply the CV value by 0.98632 to find the true SHP value. Jane's did not do this nor has many of the English language sources. The reference ''French Cruisers 1922 - 1056'' shows the horse power values as only CV and gives the value for conversion to SHP used in many sources.

File:Duquesne.svg, ''Duquesne'' in original anti-surface layout
File:Tourville 1945.svg, ''Tourville'' after refit at Bizerte: changed anti-air armament, removal of sea plane, torpedo launchers and aft mast
File:Tourville (cruiser)- SLV H91.325-30.jpg, ''Tourville'' in 1929

References

Bibliography

*
*
*
*
*
*
*
*

External links

203 mm/50 (8in) Model 1924 naval gun

75 mm/50 (3.0 in) Model 1922 naval gun

37 mm/50 (1.46 in) Model 1933 naval gun

13.2 mm(0.5 in) machinegun Model 1929

French Pre-war Torpedoes

{{WWII French ships

Cruiser classes

Ship classes of the French Navy