Combustion Models For CFD
   HOME

TheInfoList



OR:

Combustion models for CFD refers to combustion models for
computational fluid dynamics Computational fluid dynamics (CFD) is a branch of fluid mechanics that uses numerical analysis and data structures to analyze and solve problems that involve fluid flows. Computers are used to perform the calculations required to simulate ...
.
Combustion Combustion, or burning, is a high-temperature exothermic redox chemical reaction between a fuel (the reductant) and an oxidant, usually atmospheric oxygen, that produces oxidized, often gaseous products, in a mixture termed as smoke. Combus ...
is defined as a chemical reaction in which a hydrocarbon fuel reacts with an oxidant to form products, accompanied with the release of energy in the form of heat. Being the integral part of various engineering applications like:
internal combustion engine An internal combustion engine (ICE or IC engine) is a heat engine in which the combustion of a fuel occurs with an oxidizer (usually air) in a combustion chamber that is an integral part of the working fluid flow circuit. In an internal c ...
s, aircraft engines,
rocket engine A rocket engine uses stored rocket propellants as the reaction mass for forming a high-speed propulsive jet of fluid, usually high-temperature gas. Rocket engines are reaction engines, producing thrust by ejecting mass rearward, in accorda ...
s, furnaces, and power station combustors, combustion manifests itself as a wide domain during the design, analysis and performance characteristics stages of the above-mentioned applications.“An introduction to Computational Fluid Dynamics-- the finite volume method” H.K. Versteeg and W.Malalasekara Pearson Education limited.p.357 With the added complexity of chemical kinetics and achieving reacting flow mixture environment, proper modeling physics has to be incorporated during computational fluid dynamic (CFD) simulations of combustion. Hence the following discussion presents a general outline of the various adequate models incorporated with the Computational fluid dynamic code to model the process of combustion.An introduction to Computational Fluid Dynamics-- the finite volume method” H.K. Versteeg and W. Malalasekera Longman Group limited.p.210


Overview

Computational fluid dynamics modeling of combustion calls upon the proper selection and implementation of a model suitable to faithfully represent the complex physical and chemical phenomenon associated with any combustion process. The model should be competent enough to deliver information related to the species concentration, their volumetric generation or destruction rate and changes in the parameters of the system like enthalpy, temperature and mixture density. The model should be capable of solving the general transport equations for fluid flow and heat transfer as well as the additional equations of combustion chemistry and
chemical kinetics Chemical kinetics, also known as reaction kinetics, is the branch of physical chemistry that is concerned with understanding the rates of chemical reactions. It is to be contrasted with chemical thermodynamics, which deals with the direction in ...
incorporated into that as per the simulating environment desired


Critical considerations in combustion phenomenon

The major consideration during any general combustion process includes the mixing time scale and the reacting time scale elapsed for the process. The flame type and the type of mixing of flow streams of the constituents also have to be taken into account. Apart from that as far as the kinetic complexity of the reaction is concerned, the reaction proceeds in multiple steps and what appears as a simple one line reaction actually completes after a series of reactions. Also the transport equations for mass fractions of all the species as well as the enthalpy generated during the reaction have to be solved. Hence even the simplest combustion reaction involves very tedious and rigorous calculation if all the intermediate steps of the combustion process, all transport equations and all flow equations have to be satisfied simultaneously. All these factors will have a significant effect on the computational speed and time of the simulation. But with proper simplifying assumptions Computational fluid dynamic modeling of combustion reaction can be done without substantial compromise on the accuracy and convergence of the solution. The basic models used for the same are covered in the following paragraphs.


Simple chemical reacting system model

This model takes into consideration only the final concentration of species and takes into account only the global nature of combustion process where the reaction proceeds infinitely fast as a single step process without much stress on the detailed kinetics involved. The reactants are assumed to react in
stoichiometric Stoichiometry refers to the relationship between the quantities of reactants and products before, during, and following chemical reactions. Stoichiometry is founded on the law of conservation of mass where the total mass of the reactants equ ...
proportions. The model also deduces a linear relationship between the mass fractions of fuel, oxidant and the non dimensional variable mixture fraction. The model also takes into account an additional assumption that the mass diffusion coefficients of all species are equal. Owing to this additional assumption the model only solves one extra partial differential equation for mixture fraction and after solving the transport equation for the mixture fraction the corresponding mass fractions for fuel and oxidant are calculated. This model can very well be applied to a combustion environment where laminar diffusion effects are dominant and the combustion proceeds via non premixed fuel and oxidant streams diffusing into each other giving rise to a laminar flame.


Eddy break–up model

This model is used when turbulent mixing of the constituents has to be taken into consideration. The k/Ɛ turbulent time scale is used to calculate the reaction rate. A comparison between the turbulent dissipation rates of the fuel, oxidant and products is done and the minimum amongst all is taken as the rate of the reaction. The transport equations for the mass fractions of the constituents are solved using this rate of reaction. Apart from this a mean enthalpy equation is also solved and temperature, density and viscosity are calculated accordingly. The model can also be implemented when finite rate kinetically controlled reaction is to be simulated. In such situation while deciding the rate of the reaction the Arrhenius kinetic rate expression is also taken into account and the rate of reaction is taken as minimum amongst the turbulent dissipation rates of all the constituents and the Arrhenius kinetic rate expression. Since turbulent mixing governs the characteristics of this model, there exists a limit to the quality of the combustion simulation depending upon the type of the turbulent model implemented to represent the flow. The model can also be modified to account for mixing of fine structures during the turbulent reaction. This modification of the model results in the eddy dissipation model which consider the mass fraction of fine structures in its calculations.


Laminar flamelet model

{{main, Laminar flamelet model This model approximates the turbulent flame as a series of laminar flamelet regions concentrated just around the stoichiometric surfaces of the reacting mixture. This model exploits the use of experimental data for determining relations between the variables considered like mass fraction, temperature etc. The nature and type of dependence of the variables is predicted through experimental data obtained during laminar diffusion flame experiment and laminar flamelet relationship is deduced based on the same. These relationships are then used to solve the transport equations for species mass fraction and mixture composition. The model can very well be implemented for situations where concentration of minor species in the combustion is to be computed like quantifying the generation of pollutants. A simple enhancement to the model results in the flamelet time scale model which takes finite rate kinetics effect into consideration. The flamelet time scale model produces steady laminar flamelet solution when reaction proceeds very fast and captures the finite rate effects when reaction chemistry is dominant.9-rao-rutland.pdf---“A Flamelet Time Scale combustion model for turbulent combustion in KIVA” Shrikanth Rao and Christopher J. Rutland( Engine Research Center, UW Madison.)


Presumed probability distribution function model

This model takes into account a statistical approach for calculating the variables like species mass fractions, temperature and density while the mixture composition is calculated at the grids. Then these all variables are calculated as functions of the mixture fraction around a presumed probability distribution function.Pope_NACM_91.pdf—“combustion modeling using probability density function methods” S.B.Pope. The model can produce satisfactory results for turbulent reactive flows where convection effects due to mean and fluctuating components of velocity are dominant.Pope_ACAC_97.pdf---“Turbulence Combustion Modelling: fluctuations and chemistry (advanced computation and analysis of combustion: 310-320)” S.B.Pope (Sibley School of Mechanical and Aerospace Engineering Cornell University,Ithaca NY). The model can be extended for adiabatic as well as non adiabatic conditions.


Conditional moment closure

Conditional moment closure (CMC) is an advanced combustion model. The basic idea is to model the chemical source based on conditional averages. The model was first introduced for non-premixed flows and hence the conditioning is done in the mixture fraction.Cant, R.S. & Mastorakos, E. ''An Introduction to Turbulent Reacting Flows''. Imperial College Press, London. 2007.


Other models

The following are some of the other relevant models used for computational fluid dynamic modeling of combustion. * The chemical equilibrium model * The Flamelet generated manifold model * The flame surface density model * The large eddy simulation model The chemical equilibrium model considers the effect of intermediate reactions during turbulent combustion. The concentration of species is calculated when the combustion reaction reaches equilibrium state. The species concentration is calculated as a function of mixture fraction by deploying certain equilibrium calculation programs available to serve the purpose. The conditional closure model solves the transport equations for the mean components of the flow properties without considering the fluctuating composition of the reaction mixture.


References

Computational fluid dynamics Combustion engineering