Cutting is the separation or opening of a physical object, into two or more portions, through the application of an acutely directed

force In physics, a force is an influence that can change the motion of an object. A force can cause an object with mass to change its velocity (e.g. moving from a state of rest), i.e., to accelerate. Force can also be described intuitively as a p ...

. Implements commonly used for cutting are the knife and saw, or in medicine and science the scalpel and

microtome A microtome (from the Greek ''mikros'', meaning "small", and ''temnein'', meaning "to cut") is a cutting tool used to produce extremely thin slices of material known as ''sections''. Important in science, microtomes are used in microscopy, allow ...

. However, any sufficiently sharp object is capable of cutting if it has a hardness sufficiently larger than the object being cut, and if it is applied with sufficient force. Even liquids can be used to cut things when applied with sufficient force (see water jet cutter). Cutting is a compressive and shearing phenomenon, and occurs only when the total stress generated by the cutting implement exceeds the ultimate strength of the material of the object being cut. The simplest applicable equation is:

\text =

\tau=\frac

The stress generated by a cutting implement is directly proportional to the force with which it is applied, and inversely proportional to the area of contact. Hence, the smaller the area (i.e., the sharper the cutting implement), the less force is needed to cut something. It is generally seen that cutting edges are thinner for cutting soft materials and thicker for harder materials. This progression is seen from

kitchen knife A kitchen knife is any knife that is intended to be used in food preparation. While much of this work can be accomplished with a few general-purpose knives – notably a large chef's knife, a tough cleaver, a small paring knife and some sort of ...

, to cleaver, to axe, and is a balance between the easy cutting action of a thin blade vs strength and edge durability of a thicker blade.

Metal cutting

Cutting has been at the core of manufacturing throughout history. For metals many methods are used and can be grouped by the physical phenomenon used. It is the process of producing a work piece by removing unwanted material from a block of metal, in the form of chips. * Chip forming (material removal processes) – sawing,

drilling Drilling is a cutting process where a drill bit is spun to cut a hole of circular cross-section in solid materials. The drill bit is usually a rotary cutting tool, often multi-point. The bit is pressed against the work-piece and rotated at ra ...

milling Milling may refer to: * Milling (minting), forming narrow ridges around the edge of a coin * Milling (grinding), breaking solid materials into smaller pieces by grinding, crushing, or cutting in a mill * Milling (machining), a process of using rota ...

, turning etc. * Shearing – punching, stamping, scissoring, blanking * Abrasive material removal – grinding, lapping,

polishing Polishing is the process of creating a smooth and shiny surface by rubbing it or by applying a chemical treatment, leaving a clean surface with a significant specular reflection (still limited by the index of refraction of the material accordin ...

, water-jet * Heat – flame cutting, plasma cutting,

laser cutting Laser cutting is a technology that uses a laser to vaporize materials, resulting in a cut edge. While typically used for industrial manufacturing applications, it is now used by schools, small businesses, architecture, and hobbyists. Laser cutt ...

* Electrochemical – etching, electrical discharge machining (EDM),

electrochemical machining Electrochemical machining (ECM) is a method of removing metal by an electrochemical process. It is normally used for mass production and is used for working extremely hard materials or materials that are difficult to machine using conventional met ...

(ECM) Every method has its limitations in accuracy, cost, and effect on the material. For example, heat may damage the quality of heat treated alloys, and laser cutting is less suitable for highly reflective materials such as aluminum. Laser cutting sheet metal produces flat parts and etches and engraves parts from complex or simple designs. It is used over other cutting options for its quick process and customizable abilities.

References

External links

*
How stuff works – Handsaws

Etching vs. traditional metal machining
{{Authority control de:Zerspanen

Metal cutting

See also

References

External links