In electronics, two anti-parallel or inverse-parallel devices are connected in

parallel Parallel is a geometric term of location which may refer to: Computing * Parallel algorithm * Parallel computing * Parallel metaheuristic * Parallel (software), a UNIX utility for running programs in parallel * Parallel Sysplex, a cluster of ...

but with their polarities reversed. One example is the

TRIAC A TRIAC (triode for alternating current; also bidirectional triode thyristor or bilateral triode thyristor) is a three terminal electronic component that conducts current in either direction when triggered. The term TRIAC is a genericised trade ...

, which is comparable to two

thyristors A thyristor () is a solid-state semiconductor device with four layers of alternating P- and N-type materials used for high-power applications. It acts exclusively as a bistable switch (or a latch), conducting when the gate receives a current t ...

connected back-to-back (in other words, reverse parallel), but on a single piece of

silicon Silicon is a chemical element with the symbol Si and atomic number 14. It is a hard, brittle crystalline solid with a blue-grey metallic luster, and is a tetravalent metalloid and semiconductor. It is a member of group 14 in the periodic ta ...

. Two LEDs can be paired this way, so that each protects the other from

reverse voltage The breakdown voltage of an insulator is the minimum voltage that causes a portion of an insulator to experience electrical breakdown and become electrically conductive. For diodes, the breakdown voltage is the minimum reverse voltage that make ...

. A series string of such pairs can be connected to AC or DC power, with an appropriate resistor. Some two-color LEDs are constructed this way, with the 2 dies connected anti-parallel in one

chip package Integrated circuits are put into protective packages to allow easy handling and assembly onto printed circuit boards and to protect the devices from damage. A very large number of different types of package exist. Some package types have stand ...

. With AC, the LEDs in each pair take turns emitting light, on alternate half-cycles of supply power, greatly reducing the strobing effect to below the normal

flicker fusion threshold The flicker fusion threshold, critical flicker frequency (CFF) or flicker fusion rate, is a concept in the psychophysics of vision. It is defined as the frequency at which an intermittent light stimulus appears to be completely steady to the avera ...

of the human eye, and making the lights brighter. On DC, polarity can be switched back and forth so as to change the color of the lights, such as in

Christmas lights Christmas lights (also known as fairy lights, festive lights or string lights) are lights often used for decoration in celebration of Christmas, often on display throughout the Christmas season including Advent and Christmastide. The custom g ...

that can be either white or colored. Battery-powered lights, which are wired in parallel, can also create a simulated "chasing" effect by alternating the polarity for each LED attached to the string, and controlling the positive and negative parts of the cycle separately. This creates two "virtual circuits", with odd-numbered LEDs lighting on positive polarity and even-numbered ones on negative polarity, for example. By eliminating the need for extra wires, this reduces costs for the manufacturer, and makes the cords less bulky and obvious for the consumer to string on decorative items. On cheaper sets, this causes strobing and prevents any of the LEDs from getting to full brightness, since both polarities share the same wire pair and cannot be active at the same time, meaning each can only be on during its own half of the cycle. Better lights can adjust the duty cycle so that any unused "off" time on one polarity can be used by the other, reducing the strobing effect and making it easier to create color blends (such as orange, amber, and yellow from a red/green LED).

ESD

Antiparallel diodes are often used for ESD protection in ICs. Different ground or supply domains at the same potential or voltage may be wired separately for isolation reasons. However, during an ESD event across the domains, one would want a path for the high current to traverse. Without the antiparallel diodes in place, the voltage induced by the ESD event may result in the current following an unknown path that often leads to damage of the device. With the diodes in place the current can travel in either direction.

References

* https://www.researchgate.net/post/Why_are_diodes_connected_anti-parallel_across_the_MOSFET_or_IGBT_in_Inverter_Module * https://www.utdallas.edu/~torlak/courses/ee3311/lectures/lecture3.pdf * https://ieeexplore.ieee.org/document/4159554/ * https://www.scientific.net/AMR.328-330.32 Electronic circuits {{electronics-stub

ESD

See also

References