Atmospheric Drag

In fluid dynamics, drag (sometimes called air resistance, a type of friction, or fluid resistance, another type of friction or fluid friction) is a force acting opposite to the relative motion of any object moving with respect to a surrounding fluid. This can exist between two fluid layers (or surfaces) or between a fluid and a solid surface. Unlike other resistive forces, such as dry friction, which are nearly independent of velocity, the drag force depends on velocity.

Drag force is proportional to the velocity for low-speed flow and the squared velocity for high speed flow, where the distinction between low and high speed is measured by the Reynolds number. Even though the ultimate cause of drag is viscous friction, turbulent drag is independent of viscosity.

Drag forces always tend to decrease fluid velocity relative to the solid object in the fluid's path.

Examples

Examples of drag include the component of the net aerodynamic or hydrodynamic force acting opposite to the direction of movement of a solid object such as cars (automobile drag coefficient), aircraft and boat hulls; or acting in the same geographical direction of motion as the solid, as for sails attached to a down wind sail boat, or in intermediate directions on a sail depending on points of sail. In the case of viscous drag of fluid in a pipe, drag force on the immobile pipe decreases fluid velocity relative to the pipe.

In the physics of sports, the drag force is necessary to explain the motion of balls, javelins, arrows and frisbees and the performance of runners and swimmers.

Types

Types of drag are generally divided into the following categories:
*form drag or pressure drag due to the size and shape of a body
*skin friction drag or viscous drag due to the friction between the fluid and a surface which may be the outside of an object or inside such as the bore of a pipe
The effect of streamlining on the relative proportions of skin friction and form drag is shown for two different body sections, an airfoil, which is a streamlined body, and a cylinder, which is a bluff body. Also shown is a flat plate illustrating the effect that orientation has on the relative proportions of skin friction and pressure difference between front and back. A body is known as bluff (or blunt) if the source of drag is dominated by pressure forces and streamlined if the drag is dominated by viscous forces. Road vehicles are bluff bodies. For aircraft, pressure and friction drag are included in the definition of parasitic drag. Parasite drag is often expressed in terms of a hypothetical (in so far as there is no edge spillage drag) "equivalent parasite drag area" which is the area of a flat plate perpendicular to the flow. It is used for comparing the drag of different aircraft. For example, the Douglas DC-3 has an equivalent parasite area of 23.7 sq ft and the McDonnell Douglas DC-9, with 30 years of advancement in aircraft design, an area of 20.6 sq ft although it carried five times as many passengers.
*lift-induced drag appears with wings or a lifting body in aviation and with semi-planing or planing hulls for watercraft
*wave drag (aerodynamics) is caused by the presence of shockwaves and first appears at subsonic aircraft speeds when local flow velocities become supersonic. The wave drag of the supersonic Concorde prototype aircraft was reduced at Mach 2 by 1.8% by applying the area rule which extended the rear fuselage 3.73m on the production aircraft.
* wave resistance (ship hydrodynamics) or wave drag occurs when a solid object is moving along a fluid boundary and making surface waves
*boat-tail drag on an aircraft is caused by the angle with which the rear fuselage, or engine nacelle, narrows to the engine exhaust diameter.

File:Concorde first visit Heathrow Fitzgerald.jpg, Concorde with 'high' wave drag tail
File:Aerospatial Concorde (6018513515).jpg, Concorde with 'low' wave drag tail
File:BAe Hawk Mk127 76 Sqn RAAF rear view.jpg, Hawk aircraft showing base area above circular engine exhaust

The drag equation

Drag depends on the properties of the fluid and on the size, shape, and speed of the object. One way to express this is by means of the drag equation:
:$F_D\, =\, \tfrac12\, \rho\, v^2\, C_D\, A$
where
:''$F_D$'' is the drag force,
:$\rho$ is the density of the fluid,
:''$v$'' is the speed of the object relative to the fluid,
:''$A$'' is the cross sectional area, and
:''$C_D$'' is the drag coefficient – a dimensionless number.
The drag coefficient depends on the shape of the object and on the Reynolds number
:$R_e=\frac=\frac$,

where
:''$D$'' is some characteristic diameter or linear dimension. Actually ''$D$'' it is the equivalent diameter ''$D_$''of the object. For a sphere $D_$ is the D of the sphere itself.
:For a rectangular shape cross-section in the motion direction, $D_ = 1.30 \cdot \frac$, where a and b are the rectangle edges.
: $$ is the kinematic viscosity of the fluid (equal to the dynamic viscosity $$ divided by the density $$ ).

At low $R_e$, $C_D$ is asymptotically proportional to $R_e^$, which means that the drag is linearly proportional to the speed, i.e. the drag force on a small sphere moving through a viscous fluid is given by the Stokes Law:
:$F_ = 6 \pi \mu R v$
At high $R_e$, $C_D$ is more or less constant and drag will vary as the square of the speed. The graph to the right shows how $C_D$ varies with $R_e$ for the case of a sphere. Since the power needed to overcome the drag force is the product of the force times speed, the power needed to overcome drag will vary as the square of the speed at low Reynolds numbers and as the cube of the speed at high numbers.

It can be demonstrated that drag force can be expressed as a function of a dimensionless number, which is dimensionally identical to the Bejan number.Liversage, P., and Trancossi, M. (2018). Analysis of triangular sharkskin profiles according to second law, Modelling, Measurement and Control B. 87(3), 188-196. http://www.iieta.org/sites/default/files/Journals/MMC/MMC_B/87.03_11.pdf Consequently, drag force and drag coefficient can be a function of Bejan number. In fact, from the expression of drag force it has been obtained:

:$D = \Delta_p A_w = \frac C_D A_f \frac Re_L^2$

and consequently allows expressing the drag coefficient $C_D$ as a function of Bejan number and the ratio between wet area $A_w$ and front area $A_f$:

:$C_D = 2\frac\frac$

where $Re_L$is the Reynolds number related to fluid path length L.

At high velocity

As mentioned, the drag equation with a constant drag coefficient gives the force experienced by an object moving through a fluid at relatively large velocity (i.e. high Reynolds number, Re > ~1000). This is also called ''quadratic drag''. The equation is attributed to Lord Rayleigh, who originally used ''L''² in place of ''A'' (''L'' being some length).

:$F_D\, =\, \tfrac12\, \rho\, v^2\, C_d\, A,$
^{see derivation}

The reference area ''A'' is often orthographic projection of the object (frontal area)—on a plane perpendicular to the direction of motion—e.g. for objects with a simple shape, such as a sphere, this is the cross sectional area. Sometimes a body is a composite of different parts, each with a different reference areas, in which case a drag coefficient corresponding to each of those different areas must be determined.

In the case of a wing the reference areas are the same and the drag force is in the same ratio to the lift force as the ratio of drag coefficient to lift coefficient. Therefore, the reference for a wing is often the lifting area ("wing area") rather than the frontal area.

For an object with a smooth surface, and non-fixed separation points—like a sphere or circular cylinder—the drag coefficient may vary with Reynolds number ''R_e'', even up to very high values (''R_e'' of the order 10⁷).

Batchelor (1967), p. 341.
For an object with well-defined fixed separation points, like a circular disk with its plane normal to the flow direction, the drag coefficient is constant for ''R_e'' > 3,500.
Further the drag coefficient ''C_d'' is, in general, a function of the orientation of the flow with respect to the object (apart from symmetrical objects like a sphere).

Power

Under the assumption that the fluid is not moving relative to the currently used reference system, the power required to overcome the aerodynamic drag is given by:

:$P_d = \mathbf_d \cdot \mathbf = \tfrac12 \rho v^3 A C_d$

Note that the power needed to push an object through a fluid increases as the cube of the velocity. A car cruising on a highway at may require only to overcome aerodynamic drag, but that same car at requires . With a doubling of speed the drag (force) quadruples per the formula. Exerting 4 times the force over a fixed distance produces 4 times as much work. At twice the speed the work (resulting in displacement over a fixed distance) is done twice as fast. Since power is the rate of doing work, 4 times the work done in half the time requires 8 times the power.

When the fluid is moving relative to the reference system (e.g. a car driving into headwind) the power required to overcome the aerodynamic drag is given by:

:$P_d = \mathbf_d \cdot \mathbf = \tfrac12 C_d A \rho (v_w + v_o)^3$

Where $v_w$ is the wind speed and $v_o$ is the object speed (both relative to ground).

Velocity of a falling object

The velocity as a function of time for an object falling through a non-dense medium, and released at zero relative-velocity ''v'' = 0 at time ''t'' = 0, is roughly given by a function involving a hyperbolic tangent (tanh):

:$v(t) = \sqrt \tanh \left(t \sqrt \right). \,$

The hyperbolic tangent has a limit value of one, for large time ''t''. In other words, velocity asymptotically approaches a maximum value called the terminal velocity ''v_t'':

:$v_ = \sqrt. \,$

For an object falling and released at relative-velocity ''v'' = v_i at time ''t'' = 0, with v_i < v_t, is also defined in terms of the hyperbolic tangent function:

:$v(t) = v_t \tanh \left( t \frac + \operatorname\left( \frac \right) \right). \,$

For v_i > v_t, the velocity function is defined in terms of the hyperbolic cotangent function:

:$v(t) = v_t \coth \left( t \frac + \coth^\left( \frac \right) \right). \,$

The hyperbolic cotangent has also a limit value of one, for large time ''t''. Velocity asymptotically tends to the terminal velocity ''v_t'', strictly from above ''v_t''.

For v_i = v_t, the velocity is constant:

:$v(t) = v_t. \,$

Actually, these functions are defined by the solution of the following differential equation:

:$g - \frac v^2 = \frac. \,$

Or, more generically (where ''F''(''v'') are the forces acting on the object beyond drag):

:$\frac\sum F(v) - \frac v^2 = \frac. \,$

For a potato-shaped object of average diameter ''d'' and of density ''ρ_obj'', terminal velocity is about

:$v_ = \sqrt. \,$

For objects of water-like density (raindrops, hail, live objects—mammals, birds, insects, etc.) falling in air near Earth's surface at sea level, the terminal velocity is roughly equal to

:$v_ = 90 \sqrt, \,$

with ''d'' in metre and ''v_t'' in m/s. For example, for a human body ($\mathbf d$ ≈0.6 m) $\mathbf v_t$ ≈70 m/s, for a small animal like a cat ($\mathbf d$ ≈0.2 m) $\mathbf v_t$ ≈40 m/s, for a small bird ($\mathbf d$ ≈0.05 m) $\mathbf v_t$ ≈20 m/s, for an insect ($\mathbf d$ ≈0.01 m) $\mathbf v_t$ ≈9 m/s, and so on. Terminal velocity for very small objects (pollen, etc.) at low Reynolds numbers is determined by Stokes law.

Terminal velocity is higher for larger creatures, and thus potentially more deadly. A creature such as a mouse falling at its terminal velocity is much more likely to survive impact with the ground than a human falling at its terminal velocity. A small animal such as a cricket impacting at its terminal velocity will probably be unharmed. This, combined with the relative ratio of limb cross-sectional area vs. body mass (commonly referred to as the square–cube law), explains why very small animals can fall from a large height and not be harmed.

Very low Reynolds numbers: Stokes' drag

The equation for viscous resistance or linear drag is appropriate for objects or particles moving through a fluid at relatively slow speeds where there is no turbulence (i.e. low Reynolds number, $R_e < 1$). Note that purely laminar flow only exists up to Re = 0.1 under this definition. In this case, the force of drag is approximately proportional to velocity. The equation for viscous resistance is:

:$\mathbf_d = - b \mathbf \,$

where:
:$\mathbf b$ is a constant that depends on both the material properties of the object and fluid, as well as the geometry of the object; and
:$\mathbf$ is the velocity of the object.

When an object falls from rest, its velocity will be

:$v(t) = \frac\left(1-e^\right)$
where:
:$\rho$ is the density of the object,
:$\rho_0$ is density of the fluid,
:$V$ is the volume of the object,
:$g$ is the acceleration due to gravity (i.e., 9.8 m/s$^2$), and
:$m$ is mass of the object.

The velocity asymptotically approaches the terminal velocity $\mathbf v_t = \frac$. For a given $\mathbf b$, denser objects fall more quickly.

For the special case of small spherical objects moving slowly through a viscous fluid (and thus at small Reynolds number), George Gabriel Stokes derived an expression for the drag constant:

:$b = 6 \pi \eta r\,$

where:
:$\mathbf r$ is the Stokes radius of the particle, and $\mathbf \eta$ is the fluid viscosity.

The resulting expression for the drag is known as Stokes' drag:

:$\mathbf_d = -6 \pi \eta r\, \mathbf.$

For example, consider a small sphere with radius $\mathbf r$ = 0.5 micrometre (diameter = 1.0 µm) moving through water at a velocity $\mathbf v$ of 10 µm/s. Using 10⁻³ Pa·s as the dynamic viscosity of water in SI units,
we find a drag force of 0.09 pN. This is about the drag force that a bacterium experiences as it swims through water.

The drag coefficient of a sphere can be determined for the general case of a laminar flow with Reynolds numbers less than 1$2 \cdot 10^5$ using the following formula:

$C_D = \frac +\frac+0.4 ~\text~~~~~Re<2\cdot 10^5$

For Reynolds numbers less than 1, Stokes' law applies and the drag coefficient approaches $\frac$!

Aerodynamics

In aerodynamics, aerodynamic drag is the fluid drag force that acts on any moving solid body in the direction of the fluid freestream flow. From the body's perspective (near-field approach), the drag results from forces due to pressure distributions over the body surface, symbolized $D_$, and forces due to skin friction, which is a result of viscosity, denoted $D_$. Alternatively, calculated from the flowfield perspective (far-field approach), the drag force results from three natural phenomena: shock waves, vortex sheet, and viscosity.

Overview

The pressure distribution acting on a body's surface exerts normal forces on the body. Those forces can be summed and the component of that force that acts downstream represents the drag force, $D_$, due to pressure distribution acting on the body. The nature of these normal forces combines shock wave effects, vortex system generation effects, and wake viscous mechanisms.

The viscosity of the fluid has a major effect on drag. In the absence of viscosity, the pressure forces acting to retard the vehicle are canceled by a pressure force further aft that acts to push the vehicle forward; this is called pressure recovery and the result is that the drag is zero. That is to say, the work the body does on the airflow, is reversible and is recovered as there are no frictional effects to convert the flow energy into heat. Pressure recovery acts even in the case of viscous flow. Viscosity, however results in pressure drag and it is the dominant component of drag in the case of vehicles with regions of separated flow, in which the pressure recovery is fairly ineffective.

The friction drag force, which is a tangential force on the aircraft surface, depends substantially on boundary layer configuration and viscosity. The net friction drag, $D_f$, is calculated as the downstream projection of the viscous forces evaluated over the body's surface.

The sum of friction drag and pressure (form) drag is called viscous drag. This drag component is due to viscosity. In a thermodynamic perspective, viscous effects represent irreversible phenomena and, therefore, they create entropy. The calculated viscous drag $D_v$ use entropy changes to accurately predict the drag force.

When the airplane produces lift, another drag component results. Induced drag, symbolized $D_i$, is due to a modification of the pressure distribution due to the trailing vortex system that accompanies the lift production. An alternative perspective on lift and drag is gained from considering the change of momentum of the airflow. The wing intercepts the airflow and forces the flow to move downward. This results in an equal and opposite force acting upward on the wing which is the lift force. The change of momentum of the airflow downward results in a reduction of the rearward momentum of the flow which is the result of a force acting forward on the airflow and applied by the wing to the air flow; an equal but opposite force acts on the wing rearward which is the induced drag. Another drag component, namely wave drag, $D_w$, results from shock waves in transonic and supersonic flight speeds. The shock waves induce changes in the boundary layer and pressure distribution over the body surface.

In summary, there are three ways of categorising drag.

# Pressure drag and friction drag
# Profile drag and induced drag
# Vortex drag, wave drag and wake drag

History

The idea that a moving body passing through air or another fluid encounters resistance had been known since the time of Aristotle. According to Mervyn O'Gorman, this was named "drag" by Archibald Reith Low.https://archive.org/details/Flight_International_Magazine_1913-02-01-pdf/page/n19/mode/2up Flight, 1913, p. 126 Louis Charles Breguet's paper of 1922 began efforts to reduce drag by streamlining. Breguet went on to put his ideas into practice by designing several record-breaking aircraft in the 1920s and 1930s. Ludwig Prandtl's boundary layer theory in the 1920s provided the impetus to minimise skin friction. A further major call for streamlining was made by Sir Melvill Jones who provided the theoretical concepts to demonstrate emphatically the importance of streamlining in aircraft design.
In 1929 his paper ‘The Streamline Airplane’ presented to the Royal Aeronautical Society was seminal. He proposed an ideal aircraft that would have minimal drag which led to the concepts of a 'clean' monoplane and retractable undercarriage. The aspect of Jones's paper that most shocked the designers of the time was his plot of the horse power required versus velocity, for an actual and an ideal plane. By looking at a data point for a given aircraft and extrapolating it horizontally to the ideal curve, the velocity gain for the same power can be seen. When Jones finished his presentation, a member of the audience described the results as being of the same level of importance as the Carnot cycle in thermodynamics.

Lift-induced drag and parasitic drag

Lift-induced drag

Lift-induced drag (also called induced drag) is drag which occurs as the result of the creation of lift on a three-dimensional lifting body, such as the wing or fuselage of an airplane. Induced drag consists primarily of two components: drag due to the creation of trailing vortices (vortex drag); and the presence of additional viscous drag (lift-induced viscous drag) that is not present when lift is zero. The trailing vortices in the flow-field, present in the wake of a lifting body, derive from the turbulent mixing of air from above and below the body which flows in slightly different directions as a consequence of creation of lift.

With other parameters remaining the same, as the lift generated by a body increases, so does the lift-induced drag. This means that as the wing's angle of attack increases (up to a maximum called the stalling angle), the lift coefficient also increases, and so too does the lift-induced drag. At the onset of stall, lift is abruptly decreased, as is lift-induced drag, but viscous pressure drag, a component of parasite drag, increases due to the formation of turbulent unattached flow in the wake behind the body.

Parasitic drag

Parasitic drag, or profile drag, is drag caused by moving a solid object through a fluid. Parasitic drag is made up of multiple components including viscous pressure drag (form drag), and drag due to surface roughness (skin friction drag). Additionally, the presence of multiple bodies in relative proximity may incur so called interference drag, which is sometimes described as a component of parasitic drag.

In aviation, induced drag tends to be greater at lower speeds because a high angle of attack is required to maintain lift, creating more drag. However, as speed increases the angle of attack can be reduced and the induced drag decreases. Parasitic drag, however, increases because the fluid is flowing more quickly around protruding objects increasing friction or drag. At even higher speeds (transonic), wave drag enters the picture. Each of these forms of drag changes in proportion to the others based on speed. The combined overall drag curve therefore shows a minimum at some airspeed - an aircraft flying at this speed will be at or close to its optimal efficiency. Pilots will use this speed to maximize endurance (minimum fuel consumption), or maximize gliding range in the event of an engine failure.

Power curve in aviation

The interaction of parasitic and induced drag ''vs.'' airspeed can be plotted as a characteristic curve, illustrated here. In aviation, this is often referred to as the ''power curve'', and is important to pilots because it shows that, below a certain airspeed, maintaining airspeed counterintuitively requires ''more'' thrust as speed decreases, rather than less. The consequences of being "behind the curve" in flight are important and are taught as part of pilot training. At the subsonic airspeeds where the "U" shape of this curve is significant, wave drag has not yet become a factor, and so it is not shown in the curve.

Wave drag in transonic and supersonic flow

Wave drag (also called compressibility drag) is drag that is created when a body moves in a compressible fluid and at speeds that are close to the speed of sound in that fluid. In aerodynamics, wave drag consists of multiple components depending on the speed regime of the flight.

In transonic flight (Mach numbers greater than about 0.8 and less than about 1.4), wave drag is the result of the formation of shockwaves in the fluid, formed when local areas of supersonic (Mach number greater than 1.0) flow are created. In practice, supersonic flow occurs on bodies traveling well below the speed of sound, as the local speed of air increases as it accelerates over the body to speeds above Mach 1.0. However, full supersonic flow over the vehicle will not develop until well past Mach 1.0. Aircraft flying at transonic speed often incur wave drag through the normal course of operation. In transonic flight, wave drag is commonly referred to as transonic compressibility drag. Transonic compressibility drag increases significantly as the speed of flight increases towards Mach 1.0, dominating other forms of drag at those speeds.

In supersonic flight (Mach numbers greater than 1.0), wave drag is the result of shockwaves present in the fluid and attached to the body, typically oblique shockwaves formed at the leading and trailing edges of the body. In highly supersonic flows, or in bodies with turning angles sufficiently large, unattached shockwaves, or bow waves will instead form. Additionally, local areas of transonic flow behind the initial shockwave may occur at lower supersonic speeds, and can lead to the development of additional, smaller shockwaves present on the surfaces of other lifting bodies, similar to those found in transonic flows. In supersonic flow regimes, wave drag is commonly separated into two components, supersonic lift-dependent wave drag and supersonic volume-dependent wave drag.

The closed form solution for the minimum wave drag of a body of revolution with a fixed length was found by Sears and Haack, and is known as the Sears-Haack Distribution. Similarly, for a fixed volume, the shape for minimum wave drag is the Von Karman Ogive.

The Busemann biplane theoretical concept is not subject to wave drag when operated at its design speed, but is incapable of generating lift in this condition.

d'Alembert's paradox

In 1752 d'Alembert proved that potential flow, the 18th century state-of-the-art inviscid flow theory amenable to mathematical solutions, resulted in the prediction of zero drag. This was in contradiction with experimental evidence, and became known as d'Alembert's paradox. In the 19th century the Navier–Stokes equations for the description of viscous flow were developed by Saint-Venant, Navier and Stokes. Stokes derived the drag around a sphere at very low Reynolds numbers, the result of which is called Stokes' law.Batchelor (2000), pp. 337–343.

In the limit of high Reynolds numbers, the Navier–Stokes equations approach the inviscid Euler equations, of which the potential-flow solutions considered by d'Alembert are solutions. However, all experiments at high Reynolds numbers showed there is drag. Attempts to construct inviscid steady flow solutions to the Euler equations, other than the potential flow solutions, did not result in realistic results.

The notion of boundary layers—introduced by Prandtl in 1904, founded on both theory and experiments—explained the causes of drag at high Reynolds numbers. The boundary layer is the thin layer of fluid close to the object's boundary, where viscous effects remain important even when the viscosity is very small (or equivalently the Reynolds number is very large).

See also

* Added mass
* Aerodynamic force
* Angle of attack
* Atmospheric density
* Automobile drag coefficient
* Boundary layer
* Coandă effect
* Drag crisis
* Drag coefficient
* Drag equation
* Gravity drag
* Keulegan–Carpenter number
* Lift (force)
* Morison equation
* Nose cone design
* Parasitic drag
* Projectile motion#Trajectory of a projectile with air resistance
* Ram pressure
* Reynolds number
* Stall (fluid mechanics)
* Stokes' law
* Terminal velocity
* Wave drag
* Windage

References

*'Improved Empirical Model for Base Drag Prediction on Missile Configurations, based on New Wind Tunnel Data', Frank G Moore et al. NASA Langley Center
*'Computational Investigation of Base Drag Reduction for a Projectile at Different Flight Regimes', M A Suliman et al. Proceedings of 13th International Conference on Aerospace Sciences & Aviation Technology, ASAT- 13, May 26 – 28, 2009
*'Base Drag and Thick Trailing Edges', Sighard F. Hoerner, Air Materiel Command, in: Journal of the Aeronautical Sciences, Oct 1950, pp 622–628

Bibliography

*
*
*
*
*
*
* L. J. Clancy (1975), ''Aerodynamics'', Pitman Publishing Limited, London.
* Anderson, John D. Jr. (2000); ''Introduction to Flight'', Fourth Edition, McGraw Hill Higher Education, Boston, Massachusetts, USA. 8th ed. 2015, .

External links

Educational materials on air resistanceAerodynamic Drag
and its effect on the acceleration and top speed of a vehicle.
Vehicle Aerodynamic Drag calculator
based on drag coefficient, frontal area and speed.

Smithsonian National Air and Space Museum's How Things Fly websiteEffect of dimples on a golf ball and a car

{{Authority control

Articles containing video clips
Force