Anzani 6 on:
[Wikipedia]
[Google]
[Amazon]
Alessandro Anzani developed the first two-row radial from his earlier 3- cylinder Y engine by merging two onto the same
The crankcase was an aluminium casting and in later models contained a fuel mixing chamber. These later versions also used long bolts to attach the cylinders to the crankcase. The engine used a single, kinked crankweb, coupled to slim but broad connecting rods in order to minimise the axial displacement between the two rows. This was less than in more recent double row radials, the rear face of the front row falling on the centre plane of the back row. The engine was not strictly a radial, as the crankweb geometry slightly offset the centres of the two rows, an arrangement best seen from the back of the engine,''Flight'', 4 January 1913 fig 2 where the superimposed inlet tubes and push-rods of the later engine highlight the cylinder centre lines. Such an offset between cylinder centre line and crankshaft is often termed ''désaxé''.
The earliest of the 6-cylinder radials had a bore of 90 mm and stroke of 120 mm giving a displacement of 4.58 litres (280 cu in) and an output of 34 kW (45 hp) at 1,300 rpm. Its weight was 70 kg (154 lbs).''Flight'' 5 July 1913 A later version produced 45 kW (60 hp) from 6.23 litres (380 cu in).
crankshaft
A crankshaft is a mechanical component used in a piston engine to convert the reciprocating motion into rotational motion. The crankshaft is a rotating shaft containing one or more crankpins, that are driven by the pistons via the connecting ...
with a common crankweb.
Development
By December 1909Anzani
Anzani was an engine manufacturer founded by the Italian Alessandro Anzani (1877–1956), which produced proprietary engines for aircraft, cars, boats, and motorcycles in factories in Britain, France and Italy.
Overview
From his native Italy, An ...
had a 3-cylinder air-cooled true radial engine running, developed from the earlier 3-cylinder fan configuration engines (semi-radials) that had powered Bleriot across the Channel. By about March 1910 he had completed the first two-row radial engine, a 6-cylinder unit made by merging two 3-cylinder units together, one slightly behind the other and at an angle of 60°. The engine therefore had a lot in common with the early 3-cylinder motors: cylinders were a single iron casting with built-in valve cells and ribs, and pistons were steel with cast-iron rings. The early versions were side-valve engines with automatic (atmospheric pressure opened) inlet valves and exhaust valves mechanically operated via cams in the crankcase. By the end of 1912,''Flight'', 4 January 1913 p. 20-1 as with the smaller engines the exhaust valves were moved to the cylinder heads and operated by push-rods and rockers. The exhaust valves were at the front of the engine, with the fuel inlet manifold at the rear. A prominent pair of 150° exhaust tubes were fitted. Plugs were mounted in the cylinder sides, in the plane of the engine and on the upper side to minimise plug fouling by lubricant.
The crankcase was an aluminium casting and in later models contained a fuel mixing chamber. These later versions also used long bolts to attach the cylinders to the crankcase. The engine used a single, kinked crankweb, coupled to slim but broad connecting rods in order to minimise the axial displacement between the two rows. This was less than in more recent double row radials, the rear face of the front row falling on the centre plane of the back row. The engine was not strictly a radial, as the crankweb geometry slightly offset the centres of the two rows, an arrangement best seen from the back of the engine,''Flight'', 4 January 1913 fig 2 where the superimposed inlet tubes and push-rods of the later engine highlight the cylinder centre lines. Such an offset between cylinder centre line and crankshaft is often termed ''désaxé''.
The earliest of the 6-cylinder radials had a bore of 90 mm and stroke of 120 mm giving a displacement of 4.58 litres (280 cu in) and an output of 34 kW (45 hp) at 1,300 rpm. Its weight was 70 kg (154 lbs).''Flight'' 5 July 1913 A later version produced 45 kW (60 hp) from 6.23 litres (380 cu in).
Variants
;45 hp (34 kW) :Anzani's first two-row radial developed 34 kW (45 hp) from 4.58 L (280 cu in) displacement. ;60 hp (45 kW) :Larger cylinders gave 45 kW (60 hp) at 1,300 rpm from 6.23 L (380 cu in ) displacement. ;TNCA Aztatl :A direct copy of the 60 hp 6-cylinder Anzani, produced in Mexico by TNCA (''Talleres Nacionales de Construcciones Aeronáuticas'' - national aviation workshops).Applications
:Aeromarine EO
The Aeromarine EO was a light sport flying boat that was built in the mid-1920s.
Design and development
The Aeromarine EO was designed as an updated replacement of the Aeromarine Model 44 for the customer Earl Dodge Osborn. Osborn was a former a ...
:Austin Whippet
The Austin Whippet was a British single-seat light aircraft designed and built by the Austin Motor Company just after the First World War. It was a small single-seat biplane, intended to be an inexpensive aircraft for the amateur private pilot ...
: Caudron Type Caudron-Fabre
:Caudron Type N
The Caudron Types M and N were small, fast French sports monoplanes, flown 1911–13 under a wide range of engine powers. There was also a military version.
Design and development
Although almost all the aircraft designed by the Caudron br ...
: Caudron C.114
: Działowski D.K.D.3
: Działowski D.K.D.4
:Farman Scout
Farman Aviation Works (french: Avions Farman) was a French aircraft company founded and run by the brothers Richard, Henri, and Maurice Farman. They designed and constructed aircraft and engines from 1908 until 1936; during the French national ...
: Gabriel Śląsk
:Laird B-4
The Laird B-4, aka Laird 1915 biplane, was the fourth aircraft built by Matty Laird in the United States of America. It was an excellent aerobatic aircraft and was used very effectively in performances by Laird, as well as by Katherine Stinson d ...
: Perry Beadle T.2
:TNCA Serie A
TNCA Series A was a utility biplane made in Mexico by Talleres Nacionales de Construcciones Aeronáuticas (TNCA).
Design and development
The first Series A prototype was the result of a Morane-Moisant monoplane being converted to a biplane by ...
:TNCA Serie H
The TNCA Serie H "Parasol" was a Mexican bomber and reconnaissance aircraft manufactured by the Talleres Nacionales de Construcciones Aeronáuticas (TNCA). It was a high-wing monoplane (which was very unusual at the time), which allowed better sp ...
: Westland Woodpigeon II
Specifications (60 hp overhead valve)
See also
References
Notes
Bibliography
* * * {{Anzani aeroengines 1910s aircraft piston engines Aircraft air-cooled radial piston engines 6