|
Waviness
Waviness is the measurement of the more widely spaced component of surface texture. It is a broader view of roughness because it is more strictly defined as "the irregularities whose spacing is greater than the roughness sampling length". It can occur from machine or work deflections, chatter, residual stress, vibrations, or heat treatment.. Waviness should also be distinguished from flatness, both by its shorter spacing and its characteristic of being typically periodic in nature. Parameters There are several parameters for expressing waviness height, the most common being Wa & Wt, for ''average waviness'' and ''total waviness'', respectively. In the lateral direction along the surface, the ''waviness spacing'', Wsm, is another parameter that describes the mean spacing between periodic waviness peaks. There are numerous measurement settings which influence these resultant parameter values, which are mentioned below. One of the most important is the ''waviness evaluation leng ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
ISO 16610
ISO 16610: Geometrical product specifications (GPS) – Filtration is a standard series on filters for surface texture, and provides guidance on the use of these filters in various applications. Filters are used in surface texture in order reduce the bandwidth of analysis in order to obtain functional correlation with physical phenomena such as friction, wear, adhesion, etc. For example, filters are used to separate roughness and waviness from the primary profile, or to create a multiscale decomposition in order to identify the scale at which a phenomenon occurs. Historically, the first roughness measuring instruments - stylus profilometer - used to have electronic filters made of capacitors and resistors that filtered out low frequencies in order to retain frequencies that represent roughness. Later, digital filters replaced analog filters and international standards such as ISO 11562 for the Gaussian filter were published. Filter toolbox for surface texture Today, a full set o ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Surface Roughness
Surface roughness, often shortened to roughness, is a component of surface finish (surface texture). It is quantified by the deviations in the direction of the normal vector of a real surface from its ideal form. If these deviations are large, the surface is rough; if they are small, the surface is smooth. In surface metrology, roughness is typically considered to be the high-frequency, short-wavelength component of a measured surface. However, in practice it is often necessary to know both the amplitude and frequency to ensure that a surface is fit for a purpose. Roughness plays an important role in determining how a real object will interact with its environment. In tribology, rough surfaces usually wear more quickly and have higher friction coefficients than smooth surfaces. Roughness is often a good predictor of the performance of a mechanical component, since irregularities on the surface may form nucleation sites for cracks or corrosion. On the other hand, roughness may pr ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Surface Texture
Surface finish, also known as surface texture or surface topography, is the nature of a surface as defined by the three characteristics of lay, surface roughness, and waviness.. It comprises the small, local deviations of a surface from the perfectly flat ideal (a true plane). Surface texture is one of the important factors that control friction and transfer layer formation during sliding. Considerable efforts have been made to study the influence of surface texture on friction and wear during sliding conditions. Surface textures can be isotropic or anisotropic. Sometimes, stick-slip friction phenomena can be observed during sliding, depending on surface texture. Each manufacturing process (such as the many kinds of machining) produces a surface texture. The process is usually optimized to ensure that the resulting texture is usable. If necessary, an additional process will be added to modify the initial texture. The latter process may be grinding (abrasive cutting), polishing, ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Surface Texture Symbol
Surface finish, also known as surface texture or surface topography, is the nature of a surface as defined by the three characteristics of lay, surface roughness, and waviness.. It comprises the small, local deviations of a surface from the perfectly flat ideal (a true plane). Surface texture is one of the important factors that control friction and transfer layer formation during sliding. Considerable efforts have been made to study the influence of surface texture on friction and wear during sliding conditions. Surface textures can be isotropic or anisotropic. Sometimes, stick-slip friction phenomena can be observed during sliding, depending on surface texture. Each manufacturing process (such as the many kinds of machining) produces a surface texture. The process is usually optimized to ensure that the resulting texture is usable. If necessary, an additional process will be added to modify the initial texture. The latter process may be grinding (abrasive cutting), polis ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Ball (bearing)
Bearing balls are special highly spherical and smooth balls, most commonly used in ball bearings, but also used as components in things like freewheel mechanisms. The balls come in many different ''grades''. These grades are defined by bodies such as the American Bearing Manufacturers Association (ABMA), a body which sets standards for the precision of bearing balls. They are manufactured in machines designed specially for the job. In 2008, the United States produced 5.778 billion bearing balls. Grade Bearing balls are manufactured to a specific grade, which defines its geometric tolerances. The grades range from 2000 to 3, where the smaller the number the higher the precision. Grades are written "GXXXX", i.e. grade 100 would be "G100". Lower grades also have fewer defects, such as flats, pits, soft spots, and cuts. The surface smoothness is measured in two ways: surface roughness and waviness. Size refers to the farthest possible distance between two points on the ball's su ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Ball Bearing
A ball bearing is a type of rolling-element bearing that uses balls to maintain the separation between the bearing races. The purpose of a ball bearing is to reduce rotational friction and support radial and axial loads. It achieves this by using at least two races to contain the balls and transmit the loads through the balls. In most applications, one race is stationary and the other is attached to the rotating assembly (e.g., a hub or shaft). As one of the bearing races rotates it causes the balls to rotate as well. Because the balls are rolling they have a much lower coefficient of friction than if two flat surfaces were sliding against each other. Ball bearings tend to have lower load capacity for their size than other kinds of rolling-element bearings due to the smaller contact area between the balls and races. However, they can tolerate some misalignment of the inner and outer races. History Although bearings had been developed since ancient times, the first mod ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Engineering Mechanics
Applied mechanics is the branch of science concerned with the motion of any substance that can be experienced or perceived by humans without the help of instruments. In short, when mechanics concepts surpass being theoretical and are applied and executed, general mechanics becomes applied mechanics. It is this stark difference that makes applied mechanics an essential understanding for practical everyday life. It has numerous applications in a wide variety of fields and disciplines, including but not limited to structural engineering, astronomy, oceanography, meteorology, hydraulics, mechanical engineering, aerospace engineering, nanotechnology, Structural engineering, structural design, earthquake engineering, fluid dynamics, Planetary science, planetary sciences, and other life sciences. Connecting research between numerous disciplines, applied mechanics plays an important role in both science and engineering. Pure mechanics describes the response of bodies (solids and fluids) or ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Machinery's Handbook
''Machinery's Handbook'' ''for machine shop and drafting-room; a reference book on machine design and shop practice for the mechanical engineer, draftsman, toolmaker, and machinist'' (the full title of the 1st edition) is a classic reference work in mechanical engineering and practical workshop mechanics in one volume published by Industrial Press, New York, since 1914. The first edition was created by Erik Oberg (1881–1951) and Franklin D. Jones (1879–1967), who are still mentioned on the title page of the 29th edition (2012). Recent editions of the handbook contain chapters on mathematics, mechanics, materials, measuring, toolmaking, manufacturing, threading, gears, and machine elements, combined with excerpts from ANSI standards. The work is available in online and ebook form as well as print. During the decades from World War I to World War II, these phrases could refer to either of two competing reference books: McGraw-Hill McGraw Hill is an American educatio ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
ISO 4287
ISO is the most common abbreviation for the International Organization for Standardization. ISO or Iso may also refer to: Business and finance * Iso (supermarket), a chain of Danish supermarkets incorporated into the SuperBest chain in 2007 * Iso Omena ("Big Apple"), a shopping center in Finland * Incentive stock option, a type of employee stock option * Independent Sales Organization, a company that partners with an acquiring bank to provide merchant services * Insurance Services Office, an American insurance underwriter * Intermarket sweep order, a type of limit order on financial markets * Iso (automobile), an Italian car manufacturer Arts and entertainment * Isomorphic Algorithms (ISOs), a fictional race in the digital world of '' Tron: Legacy'' * Iso (comics), a Marvel comics character Music * ''Iso'' (album), an album by Ismaël Lô * Iceland Symphony Orchestra * Indianapolis Symphony Orchestra, Indiana, US * International Symphony Orchestra, of Sarnia, Ontario and Port ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Nonlinear Dynamics (journal)
''Nonlinear Dynamics, An International Journal of Nonlinear Dynamics and Chaos in Engineering Systems'' is a monthly peer-reviewed scientific journal covering all nonlinear dynamic phenomena associated with mechanical, structural, civil, aeronautical, ocean, electrical, and control systems. It is published by Springer Nature and the editor-in-chief of the journal is Walter Lacarbonara (Sapienza University of Rome). It should not be confused with the similarly named Russian journal ''Nelineinaya Dinamika'' (or the ''Russian Journal of Nonlinear Dynamics''). Abstracting and indexing The journal is abstracted and indexed in: According to the ''Journal Citation Reports'', the journal has a 2021 impact factor The impact factor (IF) or journal impact factor (JIF) of an academic journal is a scientometric index calculated by Clarivate that reflects the yearly mean number of citations of articles published in the last two years in a given journal, as ... of 5.741. Reference ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
.jpg "Click for more on -> Ball (bearing)")
