|
Two-port Network
A two-port network (a kind of four-terminal network or quadripole) is an electrical network ( circuit) or device with two ''pairs'' of terminals to connect to external circuits. Two terminals constitute a port if the currents applied to them satisfy the essential requirement known as the port condition: the electric current entering one terminal must equal the current emerging from the other terminal on the same port.Gray, §3.2, p. 172Jaeger, §10.5 §13.5 §13.8 The ports constitute interfaces where the network connects to other networks, the points where signals are applied or outputs are taken. In a two-port network, often port 1 is considered the input port and port 2 is considered the output port. It's used in mathematical circuit analysis. Application The two-port network model is used in mathematical circuit analysis techniques to isolate portions of larger circuits. A two-port network is regarded as a "black box" with its properties specified by a matrix of num ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Two-port Parameters
A two-port network (a kind of four-terminal network or quadripole) is an electrical network (Electrical circuit, circuit) or device with two ''pairs'' of terminals to connect to external circuits. Two terminals constitute a port (circuit theory), port if the currents applied to them satisfy the essential requirement known as the port condition: the electric current entering one terminal must equal the current emerging from the other terminal on the same port.Gray, §3.2, p. 172Jaeger, §10.5 §13.5 §13.8 The ports constitute interfaces where the network connects to other networks, the points where signals are applied or outputs are taken. In a two-port network, often port 1 is considered the input port and port 2 is considered the output port. It's used in mathematical Network analysis (electrical circuits), circuit analysis. Application The two-port network model is used in mathematical circuit analysis techniques to isolate portions of larger circuits. A two-port net ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Complex Number
In mathematics, a complex number is an element of a number system that extends the real numbers with a specific element denoted , called the imaginary unit and satisfying the equation i^= -1; every complex number can be expressed in the form a + bi, where and are real numbers. Because no real number satisfies the above equation, was called an imaginary number by René Descartes. For the complex number a+bi, is called the , and is called the . The set of complex numbers is denoted by either of the symbols \mathbb C or . Despite the historical nomenclature "imaginary", complex numbers are regarded in the mathematical sciences as just as "real" as the real numbers and are fundamental in many aspects of the scientific description of the natural world. Complex numbers allow solutions to all polynomial equations, even those that have no solutions in real numbers. More precisely, the fundamental theorem of algebra asserts that every non-constant polynomial equation with real or ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Current Mirror
A current mirror is a circuit designed to copy a current through one active device by controlling the current in another active device of a circuit, keeping the output current constant regardless of loading. The current being "copied" can be, and sometimes is, a varying signal current. Conceptually, an ideal current mirror is simply an ideal ''inverting current amplifier'' that reverses the current direction as well. Or it can consist of a current-controlled current source (CCCS). The current mirror is used to provide bias currents and active loads to circuits. It can also be used to model a more realistic current source (since ideal current sources don't exist). The circuit topology covered here is one that appears in many monolithic ICs. It is a Widlar mirror without an emitter degeneration resistor in the follower (output) transistor. This topology can only be done in an IC, as the matching has to be extremely close and cannot be achieved with discretes. Another topology is t ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Dual Impedance
Dual impedance and dual network are terms used in electronic network analysis. The dual of an impedance Z is its reciprocal, or algebraic inverse Z'=\frac. For this reason the dual impedance is also called the inverse impedance. Another way of stating this is that the dual of Z is the admittance Y'=Z. The dual of a network is the network whose impedances are the duals of the original impedances. In the case of a black-box network with multiple ports, the impedance looking into each port must be the dual of the impedance of the corresponding port of the dual network. This is consistent with the general notion duality of electric circuits, where the voltage and current are interchanged, etc., since Z=\frac yields Z'=\frac __TOC__ Scaled and normalised duals In physical units, the dual is taken with respect to some nominal or characteristic impedance. To do this, Z and Z' are scaled to the nominal impedance Z0 so that : \frac=\frac Z0 is usually taken to be a purely real ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Antimetric (electrical Networks)
An antimetric electrical network is an electrical network that exhibits anti-symmetry, symmetrical electrical properties. The term is often encountered in filter theory, but it applies to general electrical network analysis (electrical circuits), network analysis. Antimetric is the diametrical opposite of symmetric; it does not merely mean "asymmetric" (i.e., "lacking symmetry"). It is possible for networks to be symmetric or antimetric in their electrical properties without being physically or topology (electronics), topologically symmetric or antimetric. Definition References to symmetry and antimetry of a network usually refer to the input impedancesinput impedance. The input impedance of a Port (circuit theory), port is the impedance measured across that network port with nothing connected to it externally and all other ports terminated with a defined impedance. of a two-port network when correctly terminated."correctly terminated". This will most usually mean termination w ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Isolator (microwave)
An isolator is a two-port device that transmits microwave or radio frequency power in one direction only. The non-reciprocity observed in these devices usually comes from the interaction between the propagating wave and the material, which can be different with respect to the direction of propagation. It is used to shield equipment on its input side, from the effects of conditions on its output side; for example, to prevent a microwave source being detuned by a mismatched load. Non-reciprocity An isolator is a non-reciprocal device, with a non-symmetric scattering matrix. An ideal isolator transmits all the power entering port 1 to port 2, while absorbing all the power entering port 2, so that to within a phase-factor its S-matrix is :S = \begin 0 & 0 \\ 1 & 0 \end To achieve non-reciprocity, an isolator must necessarily incorporate a non-reciprocal material. At microwave frequencies, this material is usually a ferrite which is biased by a static magnetic field but can be a ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Circulator
A circulator is a passive, non-reciprocal three- or four-port device that only allows a microwave or radio-frequency signal to exit through the port directly after the one it entered. Optical circulators have similar behavior. Ports are where an external waveguide or transmission line, such as a microstrip line or a coaxial cable, connects to the device. For a three-port circulator, a signal applied to port 1 only comes out of port 2; a signal applied to port 2 only comes out of port 3; a signal applied to port 3 only comes out of port 1, and so on. An ideal three-port circulator has the following scattering matrix: :S = \begin 0 & 0 & 1\\ 1 & 0 & 0 \\ 0 & 1 & 0 \end Types Depending on the materials involved, circulators fall into two main categories: ferrite circulators and nonferrite circulators. Ferrite Ferrite circulators are radio-frequency circulators which employ magnetized microwave ferrite materials. They fall into two main classes: differential phase shift circ ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Reciprocity (electrical Networks)
Reciprocity in electrical networks is a property of a circuit that relates voltages and currents at two points. The reciprocity theorem states that the current at one point in a circuit due to a voltage at a second point is the same as the current at the second point due to the same voltage at the first. The reciprocity theorem is valid for almost all passive networks. The reciprocity theorem is a feature of a more general principle of reciprocity in electromagnetism. Description If a current, I_\text , injected into port A produces a voltage, V_\text , at port B and I_\text injected into port B produces V_\text at port A, then the network is said to be reciprocal. Equivalently, reciprocity can be defined by the dual situation; applying voltage, V_\text , at port A producing current I_\text at port B and V_\text at port B producing current I_\text at port A. In general, passive networks are reciprocal. Any network that consists entirely of ideal capacitances, inductance ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Scattering Parameters
Scattering parameters or S-parameters (the elements of a scattering matrix or S-matrix) describe the electrical behavior of linear electrical networks when undergoing various steady state stimuli by electrical signals. The parameters are useful for several branches of electrical engineering, including electronics, communication systems design, and especially for microwave engineering. The S-parameters are members of a family of similar parameters, other examples being: Y-parameters, Z-parameters, H-parameters, T-parameters or ABCD-parameters. They differ from these, in the sense that ''S-parameters'' do not use open or short circuit conditions to characterize a linear electrical network; instead, matched loads are used. These terminations are much easier to use at high signal frequencies than open-circuit and short-circuit terminations. Contrary to popular belief, the quantities are not measured in terms of power (except in now-obsolete six-port network analyzers). Modern vector ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Energy
In physics, energy (from Ancient Greek: ἐνέργεια, ''enérgeia'', “activity”) is the quantitative property that is transferred to a body or to a physical system, recognizable in the performance of work and in the form of heat and light. Energy is a conserved quantity—the law of conservation of energy states that energy can be converted in form, but not created or destroyed. The unit of measurement for energy in the International System of Units (SI) is the joule (J). Common forms of energy include the kinetic energy of a moving object, the potential energy stored by an object (for instance due to its position in a field), the elastic energy stored in a solid object, chemical energy associated with chemical reactions, the radiant energy carried by electromagnetic radiation, and the internal energy contained within a thermodynamic system. All living organisms constantly take in and release energy. Due to mass–energy equivalence, any object that has mass whe ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
-in-WG16.jpg "Click for more on -> Isolator (microwave)")
