|
Two-man Saw
A two-man saw (known colloquially as a "misery whip") is a saw designed for use by two sawyers. While some modern chainsaws are so large that they require two persons to control, two-man crosscut saws were primarily important when human power was used. Such a saw would typically be long, and sometimes up to , with a handle at each end. In some cases, such as when felling Giant Sequoias, sawblades could be brazed together end-to-end in order to create longer saws. The technique in using a two-man saw involved a sawyer standing at each end. Together the sawyers would alternate pulling the saw through the wood. If the kerf began closing, causing the saw to bind, wedges would be inserted behind the sawblade in order to keep the kerf open. Cutting from underneath a suspended log, called "underbucking", might also have been used if binding became a big problem. Many variations on the design were used, but they mainly fell into two types. Felling saws were used to fell the tree ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Loggers With Saw Next To Tree (3329045507)
Lumberjacks are mostly North American workers in the logging industry who perform the initial harvesting and transport of trees for ultimate processing into forest products. The term usually refers to loggers in the era (before 1945 in the United States) when trees were felled using hand tools and dragged by oxen to rivers. The work was difficult, dangerous, intermittent, low-paying, and involved living in primitive conditions. However, the men built a traditional culture that celebrated strength, masculinity, confrontation with danger, and resistance to modernization. Terminology The term lumberjack is of Canadian derivation. The first attested use of the word comes from an 1831 letter to the '' Cobourg Star and General Advertiser'' in the following passage: "my misfortunes have been brought upon me chiefly by an incorrigible, though perhaps useful, race of mortals called lumberjacks, whom, however, I would name the Cossack's of Upper Canada, who, having been reared amon ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Chainsaw
A chainsaw (or chain saw) is a portable gasoline-, electric-, or battery-powered saw that cuts with a set of teeth attached to a rotating chain driven along a guide bar. It is used in activities such as tree felling, limbing, bucking, pruning, cutting firebreaks in wildland fire suppression, and harvesting of firewood. Chainsaws with specially designed bar-and-chain combinations have been developed as tools for use in chainsaw art and chainsaw mills. Specialized chainsaws are used for cutting concrete during construction developments. Chainsaws are sometimes used for cutting ice; for example, ice sculpture and winter swimming in Finland. History In surgery The origin of chain saws in surgery is debated. A "flexible saw", consisting of a fine serrated link chain held between two wooden handles, was pioneered in the late 18th century (c. 1783–1785) by two Scottish doctors, John Aitken and James Jeffray, for symphysiotomy and excision of diseased bone, respectively. It was ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Crosscut Saw
A crosscut saw (thwart saw) is any saw designed for cutting wood perpendicular to (across) the wood grain. Crosscut saws may be small or large, with small teeth close together for fine work like woodworking or large for coarse work like log bucking, and can be a hand tool or power tool. The cutting edge of each tooth is angled in an alternating pattern. This design allows each tooth to act like a knife edge and slice through the wood in contrast to a rip saw, which tears along the grain, acting like a miniature chisel. Some crosscut saws use special teeth called "rakers" designed to clean out the cut strips of wood from the ''kerf''. Crosscut saws generally have smaller teeth than rip saws. Some saws, such as Japanese saws and those used by the ancient Egyptians, are designed to cut only on the pull stroke. Western saws, on the other hand, are designed to cut on the push stroke. Common features Many crosscut saws have a wooden handle with the return edge at right angles ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Giant Sequoia
''Sequoiadendron giganteum'' (giant sequoia; also known as giant redwood, Sierra redwood, Sierran redwood, California big tree, Wellingtonia or simply big treea nickname also used by John Muir) is the sole living species in the genus ''Sequoiadendron'', and one of three species of coniferous trees known as redwoods, classified in the family Cupressaceae in the subfamily Sequoioideae, together with ''Sequoia sempervirens'' (coast redwood) and ''Metasequoia glyptostroboides'' (dawn redwood). Giant sequoia specimens are the most massive trees on Earth. The common use of the name ''sequoia'' usually refers to ''Sequoiadendron giganteum'', which occurs naturally only in groves on the western slopes of the Sierra Nevada mountain range of California. The giant sequoia is listed as an endangered species by the IUCN, with fewer than 80,000 trees remaining. Since its last assessment as an endangered species in 2011, it was estimated that another 13–19% of the population (or 9,761–13,63 ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Brazing
Brazing is a metal-joining process in which two or more metal items are joined together by melting and flowing a filler metal into the joint, with the filler metal having a lower melting point than the adjoining metal. Brazing differs from welding in that it does not involve melting the work pieces. Brazing differs from soldering through the use of a higher temperature and much more closely fitted parts than when soldering. During the brazing process, the filler metal flows into the gap between close-fitting parts by capillary action. The filler metal is brought slightly above its melting ( liquidus) temperature while protected by a suitable atmosphere, usually a flux. It then flows over the base metal (in a process known as wetting) and is then cooled to join the work pieces together. A major advantage of brazing is the ability to join the same or different metals with considerable strength. Basics High-quality brazed joints require that parts be closely fitted with base m ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Kerf
A saw is a tool consisting of a tough blade, wire, or chain with a hard toothed edge. It is used to cut through material, very often wood, though sometimes metal or stone. The cut is made by placing the toothed edge against the material and moving it forcefully forth and less vigorously back or continuously forward. This force may be applied by hand, or powered by steam, water, electricity or other power source. An abrasive saw has a powered circular blade designed to cut through metal or ceramic. Terminology * Abrasive saw: A saw that cuts with an abrasive disc or band, rather than a toothed blade. * Back: the edge opposite the toothed edge. * Fleam: The angle of the faces of the teeth relative to a line perpendicular to the face of the saw. * Gullet: The valley between the points of the teeth. * Heel: The end closest to the handle. * Kerf: The narrow channel left behind by the saw and (relatedly) the measure of its width. The kerf depends on several factors: the width of ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Underbucking
Underbucking is a type of log bucking where the cuts are made upwards from the lower side of a suspended log. It is the opposite of ''overbucking'', cutting from the top side down. The tool supporting a saw in such a cut is known as the "underbuck". Overview Underbucking is called that because a Sawyer (occupation), sawyer will cut the suspended log from the underside of the log, upwards. Cutting from the top of a suspended log will cause the log to bind on the saw blade as the log sags at the cutting point. Cutting from below will cause the cut to widen as the log sags, avoiding binding on the saw blade. Tool An underbucking tool can be made using an ax driven into the side of the log so that a crosscut saw can be turned upside down. A special tool designed specifically for underbucking facilitates the job of cutting from the ground upwards. The underbuck tool is driven into the section of the log which is considered to be least likely of moving once the cut has been success ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Log Bucking
image:Log Buckers with the Madera Sugar Pine Company, 1914.jpg, A crew of log buckers with crosscut saws in 1914. image:Bucker1.jpg, Bucker limbing dead branch stubs with a chainsaw, also known as knot bumping image:Bucker2.jpg, Bucker making a bucking cut with a chainsaw Bucking is the process of cutting a felling, felled and delimbing, delimbed tree into logs. Significant value can be lost by sub-optimal bucking because logs destined for plywood, lumber, and wood pulp, pulp each have their own value and specifications for length, diameter, and defects. Cutting from the top down is ''overbucking'' and from the bottom up is ''underbucking''. In British English, the process is called logging-up or crosscutting. Methods A felled and delimbed tree is cut into logs of standard sizes, a process called ''bucking''. A logger who specialises in this job is a ''buck sawyer (occupation), sawyer''. Bucking may be done in a variety of ways depending on the logging operation. Trees that ha ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Japanese Saw
The Japanese saw or is a type of saw used in woodworking and Japanese carpentry that cuts on the pull stroke, unlike most European saws that cut on the push stroke. Japanese saws are the best known pull saws, but they are also used in China, Iran, Iraq, Korea, Nepal and Turkey. Among European saws, both coping saws for woodworking and jeweler's saws for metal working also cut on the pull stroke like Japanese saws. Cutting on the pull stroke is claimed to cut more efficiently and leave a narrower cut width (kerf). On the other hand, a pull stroke does not easily permit putting one's body weight behind a stroke. This can be readily solved by using a vice or clamping. Another disadvantage, due to the arrangement and form of the teeth, is that Japanese saws do not work as well on hardwoods as European saws do. Japanese saws were originally intended for comparatively soft woods like cypress and pine whereas European saws were intended for hard woods like oak and maple. The popularity ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Saw Pit
A saw pit or sawpit is a pit over which timber is positioned to be sawed with a long two-handled saw, usually a whipsaw, by two people, one standing above the timber and the other below. It was used for producing sawn planks from tree trunks, which could then be cut down into boards, pales, posts, etc. Many towns, villages and country estates had their own saw pits. The greatest user of sawn timber in past centuries was the shipbuilding industry. After falling, without bark, in smaller and more standardized sizes, and not intended as primary members in shipbuilding, the term 'timber' is often replaced by the term 'lumber'. Sawing A sawyer is a person who cuts ("saws") wood for a living. At one time, sawyers were important members of the rural community, because many implements, as well as buildings, were made of wood. In England, the terms used were 'bottom sawyer', for the man standing in the pit, and 'top sawyer', for the man who balanced on the log. Together, the sawyers wo ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Whipsaw
A whipsaw or pitsaw was originally a type of saw used in a saw pit, and consisted of a narrow blade held rigid by a frame and called a frame saw or sash saw (see illustrations). This evolved into a straight, stiff blade without a frame, up to 14 feet long and with a handle at each end. The upper handle was called the tiller and the lower one the box, so called from its appearance and because it could be removed when the saw was taken out of one cut to be positioned in another. The whipsaw was used close to the felling site to reduce large logs to beams and planks. Sawyers either dug a large pit or constructed a sturdy platform, enabling a two-man crew to saw, one positioned below the log called the pit-man, the other standing on top called the top-man. The saw blade teeth were angled and sharpened as a rip saw so as to only cut on the downward stroke. On the return stroke, the burden of lifting the weight of the saw was shared equally by the two sawyers, thereby reducing fat ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Mother Earth News
''Mother Earth News'' is a bi-monthly American magazine that has a circulation of 500,520 . It is published in Topeka, Kansas. Since its founding, ''Mother Earth News'' has promoted renewable energy, recycling, family farms, good agricultural practices, better eating habits, medical self-care, more meaningful education and affordable housing. The magazine approaches environmental problems from a down-to-earth, practical, simple living, how-to standpoint. History Founders John and Jane Shuttleworth started the magazine on a "shoestring" budget of $1500, published from home in 1970. The first issue was published in January of that year. (John Shuttleworth died on March 29, 2009, at his home in Evergreen, Colorado, at the age of 71.) The magazine was originally published in Madison, Ohio, and moved to Hendersonville, North Carolina, later. The headquarters is in Topeka, Kansas. It had a scrappy, no-frills style and appearance throughout the 1970s. ''Mother Earth News'' embraced ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
