|
Pritchel Hole
A pritchel is a type of punch used in forging, particularly in making nail holes in horseshoes. The horseshoe is heated and a hole is punched through 90 percent of the steel with a forepunch or drift punch. The pointed end of the tool should be kept sharp and so that the burr is cut out smoothly. The punched hole is lined up over the pritchel hole and the pritchel is driven into the hole, knocking out the remaining metal at the bottom of the punched hole. The temperature of the pritchel should be always below the ''red-hot'' stage as the tool itself will bend and lose the temper. When over-heated it is advised to cool it in water intermediately. Back pritcheling The pritchel should normally be driven from the bottom of the shoe, similarly as the nail is driven. ''Back pritcheling'' is the process of driving it from the opposite side —the hoof side— leaving burrs and resulting in the weakening and cutting the nails. Pritchel hole A pritchel hole is a round hole in an anvil. It ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Punch (engineering)
A punch is a tool used to indent or create a hole through a hard surface. They usually consist of a hard metal rod with a narrow tip at one end and a broad flat "butt" at the other. When used, the narrower end is pointed against a target surface and the broad end is then struck with a hammer or mallet, causing the blunt force of the blow to be transmitted down the rod body and focused more sharply onto a small area. Typically, woodworkers use a ball-peen hammer to strike a punch. Use Punches are used to drive fasteners such as nail (fastener), nails and dowels, making a hole, or forming an indentation/impression of the tip on a workpiece. Decorative punches may also be used to create a pattern or even form an image. Pin Metal pins and similar connectors are driven in or out of holes using a pin punch. For removal, first use a starter punch to loosen the pin, then use a pin punch to finish. Center A ''center punch'' is used to mark the center of a point. It is usua ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Forging
Forging is a manufacturing process involving the shaping of metal using localized compressive forces. The blows are delivered with a hammer (often a power hammer) or a die. Forging is often classified according to the temperature at which it is performed: cold forging (a type of cold working), warm forging, or hot forging (a type of hot working). For the latter two, the metal is heated, usually in a forge. Forged parts can range in weight from less than a kilogram to hundreds of metric tons.Degarmo, p. 389 Forging has been done by smiths for millennia; the traditional products were kitchenware, hardware, hand tools, edged weapons, cymbals, and jewellery. Since the Industrial Revolution, forged parts are widely used in mechanisms and machines wherever a component requires high strength; such forgings usually require further processing (such as machining) to achieve a finished part. Today, forging is a major worldwide industry. History Forging is one of the oldest known me ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Nail (fastener)
In woodworking and construction, a nail is a small object made of metal (or wood, called a tree nail or "trunnel") which is used as a fastener, as a peg to hang something, or sometimes as a decoration. Generally, nails have a sharp point on one end and a flattened head on the other, but headless nails are available. Nails are made in a great variety of forms for specialized purposes. The most common is a ''wire nail''. Other types of nails include '' pins'', ''tacks'', ''brads'', ''spikes'', and '' cleats.'' Nails are typically driven into the workpiece by a hammer or nail gun. A nail holds materials together by friction in the axial direction and shear strength laterally. The point of the nail is also sometimes bent over or ''clinched'' after driving to prevent pulling out. History The history of the nail is divided roughly into three distinct periods: * Hand-wrought (forged) nail (pre-history until 19th century) * Cut nail (roughly 1800 to 1914) * Wire nail (roughly 1860 ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Horseshoe
A horseshoe is a fabricated product designed to protect a horse hoof from wear. Shoes are attached on the palmar surface (ground side) of the hooves, usually nailed through the insensitive hoof wall that is anatomically akin to the human toenail, although much larger and thicker. However, there are also cases where shoes are glued. Horseshoes are available in a wide variety of materials and styles, developed for different types of horse and for the work they do. The most common materials are steel and aluminium, but specialized shoes may include use of rubber, plastic, magnesium, titanium, or copper.Price, Steven D. (ed.) ''The Whole Horse Catalog: Revised and Updated'' New York:Fireside 1998 , pp. 84–87. Steel tends to be preferred in sports in which a strong, long-wearing shoe is needed, such as polo, eventing, show jumping, and western riding events. Aluminium shoes are lighter, making them common in horse racing where a lighter shoe is desired, and often facilitate ce ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Anvil
An anvil is a metalworking tool consisting of a large block of metal (usually forged or cast steel), with a flattened top surface, upon which another object is struck (or "worked"). Anvils are as massive as practical, because the higher their inertia, the more efficiently they cause the energy of striking tools to be transferred to the work piece. In most cases the anvil is used as a forging tool. Before the advent of modern welding technology, it was the primary tool of metal workers. The great majority of modern anvils are made of cast steel that has been heat treated by either flame or electric induction. Inexpensive anvils have been made of cast iron and low quality steel, but are considered unsuitable for serious use as they deform and lack rebound when struck. Structure The primary work surface of the anvil is known as the face. It is generally made of hardened steel and should be flat and smooth with rounded edges for most work. Any marks on the face will b ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Tool
A tool is an object that can extend an individual's ability to modify features of the surrounding environment or help them accomplish a particular task. Although many animals use simple tools, only human beings, whose use of stone tools dates back hundreds of millennia, have been observed using tools to make other tools. Early human tools, made of such materials as stone, bone, and wood, were used for preparation of food, hunting, manufacture of weapons, and working of materials to produce clothing and useful artifacts. The development of metalworking made additional types of tools possible. Harnessing energy sources, such as animal power, wind, or steam, allowed increasingly complex tools to produce an even larger range of items, with the Industrial Revolution marking an inflection point in the use of tools. The introduction of widespread automation in the 19th and 20th centuries allowed tools to operate with minimal human supervision, further increasing the productivity of ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Hardy Hole
An anvil is a metalworking tool consisting of a large block of metal (usually forged or cast steel), with a flattened top surface, upon which another object is struck (or "worked"). Anvils are as massive as practical, because the higher their inertia, the more efficiently they cause the energy of striking tools to be transferred to the work piece. In most cases the anvil is used as a forging tool. Before the advent of modern welding technology, it was the primary tool of metal workers. The great majority of modern anvils are made of cast steel that has been heat treated by either flame or electric induction. Inexpensive anvils have been made of cast iron and low quality steel, but are considered unsuitable for serious use as they deform and lack rebound when struck. Structure The primary work surface of the anvil is known as the face. It is generally made of hardened steel and should be flat and smooth with rounded edges for most work. Any marks on the face will b ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Metalworking Hand Tools
Metalworking hand tools are hand tools that are used in the metalworking field. Hand tools are powered solely by the operator. Slapper Both metal and wood slappers are used for metalworking. Generally wood slappers are covered with a leather-face. Slappers can be used to shrink, contour, and planish (smooth) the panel without leaving rough marks to clean up. The salapper controls more surface with each blow than a hammer can and is very easy to use because it has the same angle of attack as a body hammer. This means the user does not need to change their arm and hand position when moving from hammer to slapper. The slapper can be far more effective than the hammer for shrinking because its leverage gives greater mechanical advantage over the rough spots. The slapper is great for working metal over a T-stake or for gouging and planishing. A good slapper can make radius bends and crowns quite well. A slapper works well with forming stakes and post dollies for lightly planishing and p ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
