|
Plain-sawing
Flat sawing, flitch sawing or plain sawing is a woodworking process that produces flat-cut or plain-cut boards of lumber. Process After an initial cut through the diameter of a log, parallel cuts produce flitches—strips of lumber with consistent thickness. Two cuts on each flitch trim the bark from the sides, and reduces it to a standard board width with squared edges. Two more cuts at each end set the length. Lumber can be quickly flat-cut with a side-by-side set of mechanical saws. A slower but sturdier method involves passing the log back and forth over a single saw. To reduce buckling that may occur along the middle of flat-cut boards, the initial cut may be offset from the diameter, and resulting sections cut further before cutting the flitches. Comparison Flat-sawn wood often exhibits "flat-" or "slash grain", where the angle between the visible growth rings and the width of the board is 45° or less. This makes the wood vulnerable to deformation as it dries, or if la ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Plain Quarter Sawn
In geography, a plain is a flat expanse of land that generally does not change much in elevation, and is primarily treeless. Plains occur as lowlands along valleys or at the base of mountains, as coastal plains, and as plateaus or Highland, uplands. In a valley, a plain is enclosed on two sides, but in other cases a plain may be delineated by a complete or partial ring of hills, by mountains, or by cliffs. Where a geological region contains more than one plain, they may be connected by a Mountain pass, pass (sometimes termed a Gap (landform), gap). Coastal plains mostly rise from sea level until they run into elevated features such as mountains or plateaus. Plains are one of the major landforms on earth, where they are present on all continents, and cover more than one-third of the world's land area. Plains can be formed from flowing lava; from deposition of sediment by water, ice, or wind; or formed by erosion by the agents from hills and mountains. Biomes on plains include g ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Lumber
Lumber is wood that has been processed into dimensional lumber, including beams and planks or boards, a stage in the process of wood production. Lumber is mainly used for construction framing, as well as finishing (floors, wall panels, window frames). Lumber has many uses beyond home building. Lumber is sometimes referred to as timber as an archaic term and still in England, while in most parts of the world (especially the United States and Canada) the term timber refers specifically to unprocessed wood fiber, such as cut logs or standing trees that have yet to be cut. Lumber may be supplied either rough- sawn, or surfaced on one or more of its faces. Beside pulpwood, ''rough lumber'' is the raw material for furniture-making, and manufacture of other items requiring cutting and shaping. It is available in many species, including hardwoods and softwoods, such as white pine and red pine, because of their low cost. ''Finished lumber'' is supplied in standard sizes, mostly ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Growth Rings
Dendrochronology (or tree-ring dating) is the scientific method of dating tree rings (also called growth rings) to the exact year they were formed. As well as dating them, this can give data for dendroclimatology, the study of climate and atmospheric conditions during different periods in history from wood. Dendrochronology derives from Ancient Greek (), meaning "tree", (), meaning "time", and (), "the study of". Dendrochronology is useful for determining the precise age of samples, especially those that are too recent for radiocarbon dating, which always produces a range rather than an exact date. However, for a precise date of the death of the tree a full sample to the edge is needed, which most trimmed timber will not provide. It also gives data on the timing of events and rates of change in the environment (most prominently climate) and also in wood found in archaeology or works of art and architecture, such as old panel paintings. It is also used as a check in radiocarb ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Quarter Sawn
Quarter sawing or quartersawing is a woodworking process that produces quarter-sawn or quarter-cut boards in the rip cutting of logs into lumber. The resulting lumber can also be called ''radially-sawn'' or simply ''quartered''. There is widespread confusion between the terms ''rift sawn'' and ''quarter sawn'' with the terms defined both with opposite meanings and as synonyms. Quarter-sawn boards have greater stability of form and size with less cupping, shrinkage across the width, shake and splitting, and other good qualities. In some woods such as oak, the grain produces a decorative effect which shows a prominent ray fleck, while sapele is likely to produce a ribbon figure. Process When boards are cut from a log, they are usually rip cut along the length (axis) of the log. This can be done in three ways: plain-sawing (most common, also known as flat-sawn, bastard-sawn, through and through, and tangent-sawn), quarter-sawing (less common), or rift sawing (rare). In flat-sa ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Rift Sawn
Rift sawing is a woodworking process that aims to produce lumber that is less vulnerable to distortion than flat-sawn lumber. Rift-sawing may be done strictly along a log's radials—perpendicular to the annular growth ring orientation or wood grain—or as part of the quarter sawing process. Process Leading to some confusion, the terms "rift sawing" and "quarter sawing" are interchanged between various sources. Radial cut ''Civil Engineering Materials'' describes rift-sawing as a process where boards are cut radially. Thus, the grain is always nearly parallel to the short edge of the board and thus nearly perpendicular to the long edge of the board. This produces stable boards with comparatively thin grain; least susceptible to warping, twisting, or cupping; and hence most valued for products where dimensional stability is critical (e.g. musical instruments, high-end sports equipment). This is similar to the process used to make wood shingles. The word "rift" derives fr ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
