|
Homing (mechanical)
An incremental encoder is a linear or rotary electromechanical device that has two output signals, ''A'' and ''B'', which issue pulses when the device is moved. Together, the ''A'' and ''B'' signals indicate both the occurrence of and direction of movement. Many incremental encoders have an additional output signal, typically designated ''index'' or ''Z'', which indicates the encoder is located at a particular reference position. Also, some encoders provide a status output (typically designated ''alarm'') that indicates internal fault conditions such as a bearing failure or sensor malfunction. Unlike an absolute encoder, an incremental encoder does not indicate absolute position; it only reports changes in position and, for each reported position change, the direction of movement. Consequently, to determine absolute position at any particular moment, it is necessary to send the encoder signals to an ''incremental encoder interface'', which in turn will "track" and report the en ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Open Collector
An open collector is a common type of output found on many integrated circuits (IC), which behaves like a switch that is either connected to ground or disconnected. Instead of outputting a signal of a specific voltage or current, the output signal is applied to the base of an internal NPN transistor whose collector is externalized (open) on a pin of the IC. The emitter of the NPN transistor is connected internally to the ground pin. If the output device is a MOSFET the output is called open drain and it functions in a similar way. For example, the I²C bus and 1-Wire bus are based on this concept. Function In the picture, the transistor base is labeled "IC output". This is a signal from the internal IC logic to the transistor. This signal controls the transistor switching. The external output is the transistor collector; the transistor forms an interface between the internal IC logic and parts external to the IC. On schematic component symbols, the open output is indicated wit ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
RS-422
RS-422, also known as TIA/EIA-422, is a technical standard originated by the Electronic Industries Alliance that specifies electrical characteristics of a digital signaling circuit. It was meant to be the foundation of a suite of standards that would replace the older RS-232C standard with standards that offered much higher speed, better immunity from noise, and longer cable lengths. RS-422 systems can transmit data at rates as high as 10 Mbit/s, or may be sent on cables as long as at lower rates. It is closely related to RS-423, which uses the same signaling systems but on a different wiring arrangement. RS-422 specifies differential signaling, with every data line paired with a dedicated return line. It is the voltage difference between these two lines that define the mark and space, rather than, as in RS-232, the difference in voltage between a data line and a local ground. As the ground voltage can differ at either end of the cable, this required RS-232 to use signals with ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Incremental Pulse-diagrama-b-z
Increment or incremental may refer to: *Incrementalism, a theory (also used in politics as a synonym for gradualism) *Increment and decrement operators, the operators ++ and -- in computer programming *Incremental computing *Incremental backup, which contain only that portion that has changed since the preceding backup copy. *Increment, chess term for additional time a chess player receives on each move *Incremental games * Increment in rounding See also * * *1+1 (other) 1+1 is a mathematical expression that evaluates to: * 2 (number) (in ordinary arithmetic) * 1 (number) (in Boolean algebra with a notation where '+' denotes a logical disjunction) * 0 (number) (in Boolean algebra with a notation where '+' denotes ' ... {{Disambiguation da:Inkrementel fr:Incrémentation nl:Increment ja:インクリメント pl:Inkrementacja ru:Инкремент sr:Инкремент sv:++ ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Transistor–transistor Logic
Transistor–transistor logic (TTL) is a logic family built from bipolar junction transistors. Its name signifies that transistors perform both the logic function (the first "transistor") and the amplifying function (the second "transistor"), as opposed to earlier resistor–transistor logic (RTL) and diode–transistor logic (DTL). TTL integrated circuits (ICs) were widely used in applications such as computers, industrial controls, test equipment and instrumentation, consumer electronics, and synthesizers. After their introduction in integrated circuit form in 1963 by Sylvania Electric Products, TTL integrated circuits were manufactured by several semiconductor companies. The 7400 series by Texas Instruments became particularly popular. TTL manufacturers offered a wide range of logic gates, flip-flops, counters, and other circuits. Variations of the original TTL circuit design offered higher speed or lower power dissipation to allow design optimization. TTL devices were original ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Service Life
A product's service life is its period of use in service. Several related terms describe more precisely a product's life, from the point of manufacture, storage, and distribution, and eventual use. Service life has been defined as "a product's total life in use from the point of sale to the point of discard" and distinguished from replacement life, "the period after which the initial purchaser returns to the shop for a replacement". Determining a product's expected service life as part of business policy (product life cycle management) involves using tools and calculations from maintainability and reliability analysis. Service life represents a commitment made by the item's manufacturer and is usually specified as a median. It is the time that any manufactured item can be expected to be "serviceable" or supported by its manufacturer. Service life is not to be confused with ''shelf life'', which deals with storage time, or with technical life, which is the maximum period during ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Electrical Contacts
An electrical contact is an electrical circuit component found in electrical switches, relays, connectors and circuit breakers. Each contact is a piece of electrically conductive material, typically metal. When a pair of contacts touch, they can pass an electrical current with a certain contact resistance, dependent on surface structure, surface chemistry and contact time; when the pair is separated by an insulating gap, then the pair does not pass a current. When the contacts touch, the switch is ''closed''; when the contacts are separated, the switch is ''open''. The gap must be an insulating medium, such as air, vacuum, oil, SF6. Contacts may be operated by humans in push-buttons and switches, by mechanical pressure in sensors or machine cams, and electromechanically in relays. The surfaces where contacts touch are usually composed of metals such as silver or gold alloysMatsushita Electronics, "Relay Techninal Information: Definition of Relay Terminology", § Contact, http ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Rot Enc
Rot(s) or rotting may refer to: Decay Organic matter * Rot, decomposition of organic matter ** Dry rot, of wood ** Root rot ** Wet rot, of wood * Necrosis, of tissue Technology * Bit rot, data degradation ** Software rot, a form of bit rot * Disk rot, also called CD Rot or DVD rot, the physical decay of optical disks * Link rot, hyperlinks becoming broken Music * ''Rot'' (album), an album by German rapper Sabrina Setlur * ''Rot'' (SITD), an album by the German band SITD:* ''Rotting'' (EP), by the Brazilian metal band Sarcofago * "Rot", a song by Northlane in 2015 album ''Node'' * "Rotting", a song by Green Day in 2002 album '' Shenanigans'' Places * Rot (Bad Mergentheim), a subdivision of the town of Bad Mergentheim in Baden-Württemberg, Germany * Rot (Apfelstädt), a river of Thuringia, Germany * Rot (Danube), a river in Upper Swabia, Germany * Rot (Kocher), a river of Baden-Württemberg, Germany * Rot an der Rot, a village on the Rot river, Baden-Württemberg, Germany * ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Rise Time
In electronics, when describing a voltage or current step function, rise time is the time taken by a signal to change from a specified low value to a specified high value. These values may be expressed as ratiosSee for example , and . or, equivalently, as percentages with respect to a given reference value. In analog electronics and digital electronics, these percentages are commonly the 10% and 90% (or equivalently and ) of the output step height: however, other values are commonly used. For applications in control theory, according to , rise time is defined as "''the time required for the response to rise from to of its final value''", with 0% to 100% rise time common for underdamped second order systems, 5% to 95% for critically damped and 10% to 90% for overdamped ones.Precisely, states: "''The rise time is the time required for the response to rise from x% to y% of its final value. For overdamped second order systems, the 0% to 100% rise time is normally used, and for under ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Low-pass Filter
A low-pass filter is a filter that passes signals with a frequency lower than a selected cutoff frequency and attenuates signals with frequencies higher than the cutoff frequency. The exact frequency response of the filter depends on the filter design. The filter is sometimes called a high-cut filter, or treble-cut filter in audio applications. A low-pass filter is the complement of a high-pass filter. In optics, high-pass and low-pass may have different meanings, depending on whether referring to frequency or wavelength of light, since these variables are inversely related. High-pass frequency filters would act as low-pass wavelength filters, and vice versa. For this reason it is a good practice to refer to wavelength filters as ''short-pass'' and ''long-pass'' to avoid confusion, which would correspond to ''high-pass'' and ''low-pass'' frequencies. Low-pass filters exist in many different forms, including electronic circuits such as a hiss filter used in audio, anti-aliasing fil ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Pull-up Resistor
In electronic logic circuits, a pull-up resistor (PU) or pull-down resistor (PD) is a resistor used to ensure a known state for a signal. It is typically used in combination with components such as switches and transistors, which physically interrupt the connection of subsequent components to ground or to VCC. Closing the switch creates a direct connection to ground or VCC, but when the switch is open, the rest of the circuit would be left floating (i.e., it would have an indeterminate voltage). For a switch that is used to connect a circuit to VCC (e.g., if the switch or button is used to transmit a "high" signal), a pull-down resistor connected between the circuit and ground ensures a well-defined ground voltage (i.e. logical low) across the remainder of the circuit when the switch is open. For a switch that is used to connect a circuit to ground, a pull-up resistor (connected between the circuit and VCC) ensures a well-defined voltage (i.e. VCC, or logical high) when the ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
.svg "Click for more on -> Low-pass Filter")