|
Gybing
A jibe (US) or gybe (Britain) is a sailing maneuver whereby a sailing vessel reaching downwind turns its stern through the wind, which then exerts its force from the opposite side of the vessel. Because the mainsail boom can swing across the cockpit quickly, jibes are potentially dangerous to person and rigging compared to tacking. Therefore accidental jibes are to be avoided while the proper technique must be applied so as to control the maneuver. For square-rigged ships, this maneuver is called wearing ship. In this maneuver, the mainsail will cross the center of the boat while the jib is pulled to the other side of the boat. If a spinnaker is up, its pole will have to be manually moved to the other side, to remain opposite the mainsail. In a dinghy, raising the centerboard can increase the risk of capsizing during what can be a somewhat violent maneuver, although the opposite is true of a dinghy with a flat, planing hull profile: raising the centerboard reduces ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Spinnaker
A spinnaker is a sail designed specifically for sailing off the wind on courses between a reach (wind at 90° to the course) to downwind (course in the same direction as the wind). Spinnakers are constructed of lightweight fabric, usually nylon, and are often brightly colored. They may be designed to perform best as either a reaching or a running spinnaker, by the shaping of the panels and seams. They are attached at only three points and said to be ''flown''. Nomenclature Informal names for a spinnaker are ''kite'' or ''chute'' (owing to their resemblance to a parachute in both construction and appearance). Boats may have more than one spinnaker, differentiated by a letter to indicate symmetric (S) or asymmetric (A) and a number to indicate size (with higher numbers indicating smaller size), e.g. ''A1'' would be a large asymmetric sail and ''S3'' would be a smaller symmetric sail. Operation A spinnaker is used for sailing with the direction of the wind. Symmetrical ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Heeling (sailing)
Sailing employs the wind—acting on sails, wingsails or kites—to propel a craft on the surface of the ''water'' (sailing ship, sailboat, raft, windsurfer, or kitesurfer), on ''ice'' (iceboat) or on ''land'' (land yacht) over a chosen course, which is often part of a larger plan of navigation. From prehistory until the second half of the 19th century, sailing craft were the primary means of maritime trade and transportation; exploration across the seas and oceans was reliant on sail for anything other than the shortest distances. Naval power in this period used sail to varying degrees depending on the current technology, culminating in the gun-armed sailing warships of the Age of Sail. Sail was slowly replaced by steam as the method of propulsion for ships over the latter part of the 19th century – seeing a gradual improvement in the technology of steam through a number of stepwise developments. Steam allowed scheduled services that ran at higher average speeds than sail ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Jibing
A jibe (US) or gybe (Britain) is a sailing maneuver whereby a sailing vessel reaching downwind turns its stern through the wind, which then exerts its force from the opposite side of the vessel. Because the mainsail boom can swing across the cockpit quickly, jibes are potentially dangerous to person and rigging compared to tacking. Therefore accidental jibes are to be avoided while the proper technique must be applied so as to control the maneuver. For square-rigged ships, this maneuver is called wearing ship. In this maneuver, the mainsail will cross the center of the boat while the jib is pulled to the other side of the boat. If a spinnaker is up, its pole will have to be manually moved to the other side, to remain opposite the mainsail. In a dinghy, raising the centerboard can increase the risk of capsizing during what can be a somewhat violent maneuver, although the opposite is true of a dinghy with a flat, planing hull profile: raising the centerboard reduces hee ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Points Of Sail
A point of sail is a sailing craft's direction of travel under sail in relation to the true wind direction over the surface. The principal points of sail roughly correspond to 45° segments of a circle, starting with 0° directly into the wind. For many sailing craft 45° on either side of the wind is a ''no-go'' zone, where a sail is unable to mobilize power from the wind. Sailing on a course as close to the wind as possible—approximately 45°—is termed ''beating'', a point of sail when the sails are ''close-hauled''. At 90° off the wind, a craft is on a ''beam reach''. The point of sail between beating and a beam reach is called a ''close reach''. At 135° off the wind, a craft is on a ''broad reach''. At 180° off the wind (sailing in the same direction as the wind), a craft is ''running downwind''. A given point of sail (beating, close reach, beam reach, broad reach, and running downwind) is defined in reference to the true wind—the wind felt by a stationary observe ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Fore-and-aft Rig
A fore-and-aft rig is a sailing vessel rigged mainly with sails set along the line of the keel, rather than perpendicular to it as on a square rigged vessel. Description Fore-and-aft rigged sails include staysails, Bermuda rigged sails, gaff rigged sails, gaff sails, gunter rig, lateen sails, lug sails, tanja sails, the spanker sail on a square rig and crab claw sails. Fore-and-aft rigs include: * Rigs with one mast: the proa, the catboat, the sloop, the cutter * Rigs with two masts: the ketch, the yawl * Rigs with two or more masts: the schooner Barques and barquentines are partially square rigged and partially fore-and-aft rigged. A rig which combines both on a foremast is known as a hermaphroditic rig. History Austronesia The fore-and-aft rig is believed to have been first developed independently by the Austronesian peoples some time around 1500 BC with the invention of the crab claw sail. It is suggested that it evolved from a more primitive "V"-shaped "square" s ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Capsize
Capsizing or keeling over occurs when a boat or ship is rolled on its side or further by wave action, instability or wind force beyond the angle of positive static stability or it is upside down in the water. The act of recovering a vessel from a capsize is called righting. Capsize may result from broaching, , loss of stability due to cargo shifting or flooding, or in high speed boats, from turning too fast. If a capsized vessel has enough flotation to prevent sinking, it may recover on its own in changing conditions or through mechanical work if it is not stable inverted. Vessels of this design are called self-righting. Small vessels In dinghy sailing, a practical distinction can be made between being knocked down (to 90 degrees; on its beam-ends, figuratively) which is called a capsize, and being inverted, which is called being turtled. Small dinghies frequently capsize in the normal course of use and can usually be recovered by the crew. Some types of dinghy are occa ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Death Roll
In a keel boat, a death roll is the act of broaching to windward, putting the spinnaker pole into the water and causing a crash-jibe of the boom and mainsail, which sweep across the deck and plunge down into the water. The death roll often results in the destruction of the spinnaker pole and sometimes even the dismasting of the boat. Serious injury to crew is possible due to the swift and uncontrolled action of the boom and associated gear sweeping across the boat and crashing to the (now) leeward side. For dinghy sailors, a death roll is a common type of oscillation while running downwind. It may, and often will, result in a capsize and even a full inversion if the skipper does not take quick action to prevent one. During a death roll, the boat ''rolls'' from side to side, becoming gradually more unstable until either it capsizes or the skipper reacts correctly to prevent it. While on the dead run, off the wind, the force exerted by the sail lies almost parallel to the cente ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Chinese Gybe
A Chinese gybe on a sailing vessel is a type of gybe where the upper section of the main sail moves cross the boat, filling from the opposite side, whilst the lower section and boom remain on the original side of the vessel. It contrasts with a normal gybe, where the whole sail moves across the boat as the boat turns its stern through the wind. A Chinese gybe is usually induced by too little tension on the vang or kicking strap, allowing the boom to rise up and the leech of the sail to twist excessively. The term can be used in a different sense, in which a Chinese gybe is a gybe caused when a boat rolls excessively to windward (usually when running downwind), causing an unexpected and/or uncontrolled change in course (specifically bearing off dangerously). This sense of the term is similar to death roll In a keel boat, a death roll is the act of broaching to windward, putting the spinnaker pole into the water and causing a crash-jibe of the boom and mainsail, which sweep acr ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Broach (nautical)
A broach is an abrupt, involuntary change in a vessel's course, towards the wind, resulting from loss of directional control, when the vessel's rudder becomes ineffective. This can be caused by ''wind'' or ''wave'' action. A wind gust can heel (lean) a sailing vessel, lifting its rudder out of the water. Both power and sailing vessels can broach when wave action reduces the effectiveness of the rudder. This risk occurs when traveling in the same general direction as the waves are moving. The loss of control from either cause usually leaves the vessel beam-on to the sea, and in more severe cases the rolling moment may cause a capsize. An alternative meaning in the context of submarine operation is an unintended surfacing of a shallow-running submarine in a deep wave trough. Causes Wind Broaching caused by wind action may occur when a vessel is sailing away from the wind and its sails are suddenly overpowered by a gust of wind, causing it to heel excessively. Heeling alters t ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Preventer
A gybe preventer, preventer, or jibe-guard, is a mechanical device on a sailing vessel which limits the boom's ability to swing unexpectedly across the boat due to an unplanned accidental jibe. During an unplanned accidental jibe (or ''gybe''), neither the crew nor the boat is set up properly to execute a planned jibe. As a result, the uncontrolled boom will swing across the boat potentially inflicting injury or knocking crew members overboard. The mainsheet or traveller can also inflict serious injury. Uncontrolled jibes may also damage the boat itself. Rigging a preventer on a yacht's mainsail is often performed when the wind is behind the beam (i.e. when it's coming from more than 90° off the bow). It can also be useful at other times when there is more swell than wind, a situation when the wind may not have the strength to keep the boom in place as the boat dips and rolls. On any boat that is sailing downwind without a preventer, strict 'heads-down' procedures must be e ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Boom Vang
A boom vang (US) or kicking strap (UK) (often shortened to "vang" or "kicker") is a line or piston system on a sailboat used to exert downward force on the boom and thus control the shape of the sail. The Collins English Dictionary defines it as "A rope or tackle extended from the boom of a fore-and-aft mainsail to a deck fitting of a vessel when running, in order to keep the boom from riding up". The vang typically runs from the base of the mast to the boom. Due to the great force necessary to change the height of the boom while a boat is under sail, a line-based boom vang usually includes some sort of a pulley system. Hydraulic piston vangs are used on larger sailboats and controlled by manual or electric hydraulic pumps. By controlling leech tension, the boom vang is one way of controlling sail twist. The boom vang may also be used to flatten the mainsail on dinghies. On small sailboats and some cruising sailboats a vang may be omitted. If a vang is not installed, then th ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Boom (sailing)
In sailing, a boom is a spar (pole), along the of a fore and aft rigged sail, that greatly improves control of the angle and shape of the sail. The primary action of the boom is to keep the ''foot'' flatter when the sail angle is away from the centerline of the boat. The boom also serves as an attachment point for more sophisticated control lines. Because of the improved sail control it is rare to find a non-headsail without a boom, but lateen sails, for instance, are loose-footed. In some modern applications, the sail is rolled up into the boom for storage or reefing (shortening sail). Boom attachment The forward end of the boom attaches to a mast just below the sail, with a joint called the gooseneck. The gooseneck pivots allowing the other end of the boom to move freely. The clew (back corner) of the sail attaches to the free end of the boom. The entire ''foot'' of the sail may be attached to the boom or just the clew. If the ''foot'' is not attached to the boom, ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
.svg "Click for more on -> Boom (sailing)")