|
Signaling System No. 6
Signaling System No. 6 (SS6) was introduced in the 1970s as an early common channel signalling method for telecommunication trunks between international switching centers (ISCs). It is specified in CCITT Recommendations Q.251-Q.300.ITU-T Recommendation Q.251-Q.300 - Specifications of Signalling System No. 6 The system had limited applications since at that time the predecessor systems Signaling System No. 5 (C5) and C4 were widely in use, but there was a need to experience common channel working on a fast digital basis. Traffic switching in the ISCs was then typically handled by |
Common Channel Signaling
In telecommunication, common-channel signaling (CCS), or common-channel interoffice signaling (CCIS), is the transmission of control information ''(signaling)'' via a separate channel than that used for the messages, The signaling channel usually controls multiple message channels. In the public switched telephone network (PSTN) one channel of a communications link is typically used for the sole purpose of carrying signaling for establishment and tear down of telephone calls. The remaining channels are used entirely for the transmission of voice messages. In most cases, a single channel is sufficient to handle the call setup and call clear-down traffic for numerous bearer (voice and data) channels. The technical alternative to CCS is channel-associated signaling (CAS), in which each bearer channel has a dedicated signaling channel. CCS offers the following advantages over CAS, in the context of the PSTN: * Faster call set-up time * Greater trunking efficiency due to the quicker ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Register Signalling
In telecommunications, register signaling provides addressing information, such as the calling and/or called telephone number. R2 register signaling is an example. This is contrasted with line signaling Line signaling is a class of telecommunications signaling protocols. Line signaling is responsible for off-hook, ringing signal, answer, ground start, on-hook unidirectional supervision messaging in each direction from calling party to called pa .... References Telephony signals {{telephony-stub ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Analogue Signal
An analog signal or analogue signal (see spelling differences) is any continuous signal representing some other quantity, i.e., ''analogous'' to another quantity. For example, in an analog audio signal, the instantaneous signal voltage varies continuously with the pressure of the sound waves. In contrast, a digital signal represents the original time-varying quantity as a sampled sequence of quantized values which imposes some bandwidth and dynamic range constraints on the representation. The term ''analog signal'' usually refers to electrical signals; however, mechanical, pneumatic, hydraulic and other systems may also convey or be considered analog signals. Representation An analog signal uses some property of the medium to convey the signal's information. For example, an aneroid barometer uses rotary position as the signal to convey pressure information. In an electrical signal, the voltage, current, or frequency of the signal may be varied to represent the information. ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Circuit ID
A circuit ID is a company-specific identifier assigned to a data or voice network connection between two locations. This connection, often called a circuit, may then be leased to a customer referring to that ID. In this way, the circuit ID is similar to a serial number on any product sold from a retailer to a customer. Each circuit ID is unique, so a specific customer having many circuit connections sold to them would have many circuit IDs to refer to those connections. As an example of a use of the circuit ID, when a subscriber/customer has an issue (or trouble) with a circuit, they may contact the Controlling Local Exchange Carrier (Controlling LEC) telecommunications provider, identifying the circuit that has the issue by giving the LEC that circuit ID reference. The LEC would refer to their internal records for this circuit ID to take corrective action on the designated circuit. Telecom circuit ID formats Although telecommunication providers are not required to follow any sp ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Modem
A modulator-demodulator or modem is a computer hardware device that converts data from a digital format into a format suitable for an analog transmission medium such as telephone or radio. A modem transmits data by Modulation#Digital modulation methods, modulating one or more carrier wave signals to encode digital information, while the receiver Demodulation, demodulates the signal to recreate the original digital information. The goal is to produce a Signal (electronics), signal that can be transmitted easily and decoded reliably. Modems can be used with almost any means of transmitting analog signals, from light-emitting diodes to radio. Early modems were devices that used audible sounds suitable for transmission over traditional telephone systems and leased lines. These generally operated at 110 or 300 bits per second (bit/s), and the connection between devices was normally manual, using an attached telephone handset. By the 1970s, higher speeds of 1,200 and 2,400 ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Leased Line
A leased line is a private telecommunications circuit between two or more locations provided according to a commercial contract. It is sometimes also known as a private circuit, and as a data line in the UK. Typically, leased lines are used by businesses to connect geographically distant offices. Unlike traditional telephone lines in the public switched telephone network (PSTN) leased lines are generally not switched circuits, and therefore do not have an associated telephone number. Each side of the line is permanently connected, always active and dedicated to the other. Leased lines can be used for telephone, Internet, or other data communication services. Some are ringdown services, and some connect to a private branch exchange (PBX) or network router. The primary factors affecting the recurring lease fees are the distance between end stations and the bandwidth of the circuit. Since the connection does not carry third-party communications, the carrier can assure a specified ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Four-wire Circuit
In telecommunication, a four-wire circuit is a two-way circuit using two paths so arranged that the respective signals are transmitted in one direction only by one path and in the other direction by the other path. The four-wire circuit gets its name from the fact that is uses four conductors to create two complete electrical circuits, one for each direction. The two separate circuits (channels) allow full- duplex operation with low crosstalk. In telephony a four-wire circuit was historically used to transport and switch baseband audio signals in the phone company telephone exchange before the advent of digital modulation and the electronic switching system eliminated baseband audio from the telco plant except for the local loop. The local loop is a two-wire circuit for one reason only: to save copper. Using half the number of copper wire conductors per circuit means that the infrastructure cost for wiring each circuit is halved. Although a lower quality circuit, the local loop al ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Data Link
A data link is the means of connecting one location to another for the purpose of transmitting and receiving digital information (data communication). It can also refer to a set of electronics assemblies, consisting of a transmitter and a receiver (two pieces of data terminal equipment) and the interconnecting data telecommunication circuit. These are governed by a link protocol enabling digital data to be transferred from a data source to a data sink. Types There are at least three types of basic data-link configurations that can be conceived of and used: * Simplex communications, most commonly meaning all communications in one direction only. * Half-duplex communications, meaning communications in both directions, but not both ways simultaneously. * Duplex communications, communications in both directions simultaneously. Aviation In civil aviation, a data-link system (known as Controller Pilot Data Link Communications) is used to send information between aircraft and air tr ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Kbit/s
In telecommunications, data-transfer rate is the average number of bits (bitrate), characters or symbols (baudrate), or data blocks per unit time passing through a communication link in a data-transmission system. Common data rate units are multiples of bits per second (bit/s) and bytes per second (B/s). For example, the data rates of modern residential high-speed Internet connections are commonly expressed in megabits per second (Mbit/s). Standards for unit symbols and prefixes Unit symbol The ISQ symbols for the bit and byte are ''bit'' and ''B'', respectively. In the context of data-rate units, one byte consists of 8 bits, and is synonymous with the unit octet. The abbreviation bps is often used to mean bit/s, so that when a ''1 Mbps'' connection is advertised, it usually means that the maximum achievable bandwidth is 1 Mbit/s (one million bits per second), which is 0.125 MB/s (megabyte per second), or about 0.1192 MiB/s (mebibyte per second). The Institu ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Blue Box
A blue box is an electronic device that produces tones used to generate the in-band signaling tones formerly used within the North American long-distance telephone network to send line status and called number information over voice circuits. This allowed the user, referred to as a "phreaker", to surreptitiously place long-distance calls that would be billed to another number or dismissed entirely as an incomplete call. A number of similar "color boxes" were also created to control other aspects of the phone network. First developed in the 1960s and used by a small phreaker community, the introduction of low-cost microelectronics in the early 1970s greatly simplified these devices to the point where they could be constructed by anyone reasonably competent with a soldering iron or breadboard construction. Soon after, models of relatively low quality were being offered fully assembled, but these generally required tinkering on the part of the user to keep operational. An excepti ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Clearing (telecommunications)
Clearing, in telecommunications means: * A sequence of events used to disconnect a call and return to the ready state for the next call setup. It is sometimes, particularly in the context of common-channel signaling, called teardown. * Removal of data from an automated information system (AIS), its storage devices, and other peripheral devices with storage capacity, in such a way that the data may not be reconstructed using normal system capabilities (i.e. through the keyboard). ''Note:'' An AIS need not be disconnected from any external network before clearing takes place. Clearing enables a product to be reused within, but not outside of, a secure facility. It does not produce a declassified product by itself, but may be the first step in the declassification process. See also * Disengagement originator * National Information Systems Security Glossary Committee on National Security Systems Instruction No. 4009, National Information Assurance Glossary, published by the Un ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Call Set-up Time
In telecommunication, call setup is the process of establishing a virtual circuit across a telecommunications network. Call setup is typically accomplished using a signaling protocol. The term call set-up time has the following meanings: # The overall length of time required to establish a circuit-switched call between users. # For data communication, the overall length of time required to establish a circuit-switched call between terminals; ''i.e.,'' the time from the initiation of a call request to the beginning of the call message. ''Note:'' Call set-up time is the summation of: (a) call request time—the time from initiation of a calling signal to the delivery to the caller of a proceed-to-select signal; (b) selection time—the time from the delivery of the proceed-to-select signal until all the selection signals have been transmitted; and (c) post selection time—the time from the end of the transmission of the selection signals until the delivery of the call-connecte ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
