|
Seafarer 30
The Seafarer 30, also known as the Seafarer Swiftsure 30, is an American sailboat that was designed by McCurdy & Rhodes as a cruiser- racer and first built in 1978.Sherwood, Richard M.: ''A Field Guide to Sailboats of North America, Second Edition'', pages 222-223. Houghton Mifflin Company, 1994. Production The design was built by Seafarer Yachts in Huntington, New York, United States between 1978 and 1985, but it is now out of production. Design The Seafarer 30 is a recreational keelboat, built predominantly of fiberglass, with teak wood trim. It has a masthead sloop rig, a raked stem, a slightly reverse transom, a skeg-mounted rudder controlled by a wheel and a fixed fin keel or optional centerboard. It displaces and carries of lead ballast. The keel-equipped version of the boat has a draft of , while the centerboard-equipped version has a draft of with the centreboard retracted. A tall rig was also available, with a mast about taller than standard. The boat is fi ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
McCurdy & Rhodes
McCurdy & Rhodes is an American naval architecture design firm, originally based in Cold Spring Harbor, New York and now located in nearby Oyster Bay, New York. The company specializes in the design of fiberglass sailboats. The company was founded in 1965 by James A. McCurdy and Philip ("Bodie") H. Rhodes. Rhodes is the son of naval architect Philip L. Rhodes and both company principals got their start at Philip L. Rhodes, Naval Architects and Marine Engineers, where McCurdy was head of the Yacht Design Section and Bodie Rhodes did design work. History After its formation, the firm was involved in the design of many boats for Seafarer Yachts in the 1970s and 1980s. McCurdy's son, Ian A. McCurdy, graduated from Rensselaer Polytechnic Institute with a degree in civil engineering and also graduated from the University of Michigan, with BS and a MS degrees in naval architecture and marine engineering. In 1980, Ian A. McCurdy joined McCurdy & Rhodes from his previous post at the Am ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Teak
Teak (''Tectona grandis'') is a tropical hardwood tree species in the family Lamiaceae. It is a large, deciduous tree that occurs in mixed hardwood forests. ''Tectona grandis'' has small, fragrant white flowers arranged in dense clusters (panicles) at the end of the branches. These flowers contain both types of reproductive organs ( perfect flowers). The large, papery leaves of teak trees are often hairy on the lower surface. Teak wood has a leather-like smell when it is freshly milled and is particularly valued for its durability and water resistance. The wood is used for boat building, exterior construction, veneer, furniture, carving, turnings, and other small wood projects. ''Tectona grandis'' is native to south and southeast Asia, mainly Bangladesh, India, Indonesia, Malaysia, Myanmar, Thailand and Sri Lanka, but is naturalised and cultivated in many countries in Africa and the Caribbean. Myanmar's teak forests account for nearly half of the world's naturally occurring teak. ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Genoa (sail)
A genoa sail is a type of large jib or staysail that extends past the mast and so overlaps the main sail when viewed from the side, sometimes eliminating it. It was originally called an "overlapping jib" and later a genoa jib. It is used on single-masted sloops and twin-masted boats such as yawls and ketches. Its larger surface area increases the speed of the craft in light to moderate winds; in high wind, a smaller jib is usually substituted, and downwind a spinnaker may be used. Definition The term ''jib'' is the generic term for any of an assortment of ''headsails''. The term ''genoa'' (or genny) refers to a type of jib that is larger than the 100% foretriangle, which is the triangular area formed by the point at which the stay intersects the mast, and deck or bowsprit, and the line where the mast intersects deck at the rail. Colloquially the term is sometimes used interchangeably with ''jib''. A working jib is no larger than the 100% foretriangle. A genoa is larger, with ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Outhaul
An outhaul is a control line found on a sailboat. It is an element of the running rigging, used to attach the mainsail Parts of a sail#Corners, clew to the boom (sailing), boom and tensions the Sail components#Edges, foot of the sail. It commonly uses a Block (sailing), block at the boom end and a Cleat (nautical), cleat on the boom, closer to the mast, to secure the line. The outhaul is loosened to provide a fuller camber or tightened to give the sail foot a flatter camber. Depending on the wind, this will increase or decrease boat speed. Naval architect, Sailboat designer and sailing theorist, Frank Bethwaite, recommended that the outhaul, along with the other sail controls on a Sailing (sport), racing sailboat, should be knotted and the boom marked with the settings for different wind speeds. References {{Sail Types Sailing rigs and rigging ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Jiffy-reefing
Reefing reduces the area of a sail, usually by folding or rolling one edge of the canvas in on itself and attaching the unused portion to a spar or a stay, as the primary measure to preserve a sailing vessel's stability in strong winds. Restoring full sail area is termed ''shaking out'' a reef. Whereas fore-and-aft rigged vessels store the unused portion of the sail on a boom, below the sail, square-rigged vessels stow the unused portion on a spar, above the sail. Reefing may occur by rolling the sail around its luff or foot, either on a rotating stay or within a spar. Fore-and-aft rigs Sails may have built-in alternative attachment points that allow their area to be reduced. In a mainsail, pairs of grommets, called reefing tacks, reefing clews, or reefing cringles may be installed in the sail; a cruising boat will typically have two to three pairs. Pulling these points down to the boom forms a new tack and clew, reducing the sail's area. Using the pair of grommets closest t ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Halyard
In sailing, a halyard or halliard is a line (rope) that is used to hoist a ladder, sail, flag or yard. The term ''halyard'' comes from the phrase "to haul yards". Halyards, like most other parts of the running rigging, were classically made of natural fibre like manila or hemp. Sail types * A square rig sail with a halyard is mounted on a lifting yard that is free to slide on a short section of the mast. The halyard is used to raise (hail or hal) the yard when setting the sail. * A gaff rigged sail has two; a throat halyard to lift the end of the gaff nearer the mast, and a peak halyard to lift the outer end. * A more modern triangular (Bermuda or "Marconi") sail has only one halyard which is attached at its uppermost point (the ''head''). Fastenings Halyards can be attached a number of ways to the head of a triangular sail. The most common methods are as follows: # A shackle through a headboard on the sail. # A bowline through a hole in the head. # A half hitch with a figure ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Dorade Vents
A dorade box (also called a dorade vent, collector box, or simply a "ventilator") is a type of Ventilation (architecture), vent that permits the passage of air in and out of the cabin or engine room of a boat while keeping rain, spray, and sea wash out. Design The basic form is a low, rectangular box fixed to the deck (ship), deck or cabin (ship), cabin top, fitted with interleaving vertical baffles. The baffles alternate to be free at the floor of the box, or free at the ceiling, forming a series of chambers. A horn-shaped ventilation cowl (chimney), cowl is usually fitted facing forward to a large hole at the top of the chamber at one end of the box with another large hole opening down into the boat from the chamber at the other end. limber hole, Limber holes perforate the wall of the box at the floor of each chamber. Dorade boxes operate on the principle that air can pass relatively freely through the chambers, yet rain or sea wash will be trapped in successive chambers and ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Head (watercraft)
The head (pl. heads) is a ship's toilet. The name derives from sailing ships in which the toilet area for the regular sailors was placed at the head or bow of the ship. Design In sailing ships, the toilet was placed in the bow somewhat above the water line with vents or slots cut near the floor level allowing normal wave action to wash out the facility. Only the captain had a private toilet near his quarters, at the stern of the ship in the quarter gallery. The plans of 18th-century naval ships do not reveal the construction of toilet facilities when the ships were first built. The Journal of Aaron Thomas aboard HMS ''Lapwing'' in the Caribbean Sea in the 1790s records that a canvas tube was attached, presumably by the ship's sailmaker, to a superstructure beside the bowsprit near the figurehead, ending just above the normal waterline. In many modern boats, the heads look similar to seated flush toilets but use a system of valves and pumps that brings sea water into the to ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Galley (kitchen)
The galley is the compartment of a ship, train, or aircraft where food is cooked and prepared. It can also refer to a land-based kitchen on a naval base, or, from a kitchen design point of view, to a straight design of the kitchen layout. Ship's cooking area A galley is the cooking area aboard a vessel, usually laid out in an efficient typical style with longitudinal units and overhead cabinets. This makes the best use of the usually limited space aboard ships. It also caters for the rolling and heaving nature of ships, making them more resistant to the effects of the movement of the ship. For this reason galley stoves are often gimballed, so that the liquid in pans does not spill out. They are also commonly equipped with bars, preventing the cook from falling against the hot stove. A small cooking area on deck was called a caboose or ''camboose'', originating from the nl, kombuis, which is still in use today. In English it is a defunct term used only for a cooking area that is ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Centerboard
A centreboard or centerboard (US) is a retractable hull appendage which pivots out of a slot in the hull of a sailboat, known as a ''centreboard trunk'' (UK) or ''centerboard case'' (US). The retractability allows the centreboard to be raised to operate in shallow waters, to move the centre of lateral resistance (offsetting changes to the sailplan that move the centre of effort aft), to reduce drag when the full area of the centreboard is not needed, or when removing the boat from the water, as when trailering. A centreboard which consists of solely a pivoting metal plate is called a centerplate. A daggerboard is similar but slides vertically rather than pivoting. The analog in a scow is a bilgeboard: these are fitted in pairs and used one at a time. General History Lt. John Schank (c. 1740 – 6 February 1823) was an officer of the British Royal Navy and is credited with the invention of the centerboard. Schank, however, gave credit for the idea to British Brigadier General ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Keel
The keel is the bottom-most longitudinal structural element on a vessel. On some sailboats, it may have a hydrodynamic and counterbalancing purpose, as well. As the laying down of the keel is the initial step in the construction of a ship, in British and American shipbuilding traditions the construction is dated from this event. Etymology The word "keel" comes from Old English , Old Norse , = "ship" or "keel". It has the distinction of being regarded by some scholars as the first word in the English language recorded in writing, having been recorded by Gildas in his 6th century Latin work ''De Excidio et Conquestu Britanniae'', under the spelling ''cyulae'' (he was referring to the three ships that the Saxons first arrived in). is the Latin word for "keel" and is the origin of the term careen (to clean a keel and the hull in general, often by rolling the ship on its side). An example of this use is Careening Cove, a suburb of Sydney, Australia, where careening was carried out ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Ship's Wheel
A ship's wheel or boat's wheel is a device used aboard a water vessel to steer that vessel and control its course. Together with the rest of the steering mechanism, it forms part of the helm. It is connected to a mechanical, electric servo, or hydraulic system which alters the horizontal angle of the vessel's rudder relative to its hull. In some modern ships the wheel is replaced with a simple toggle that remotely controls an electro-mechanical or electro-hydraulic drive for the rudder, with a rudder position indicator presenting feedback to the helmsman. History Until the invention of the ship's wheel, the helmsman relied on a tiller—a horizontal bar fitted directly to the top of the rudder post—or a whipstaff—a vertical stick acting on the arm of the ship's tiller. Near the start of the 18th century, a large number of vessels appeared using the ship's wheel design, but historians are unclear when the approach was first used. Design A traditional ship's wheel is compo ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
.png "Click for more on -> Jiffy-reefing")
.svg "Click for more on -> Centerboard")
