|
Paint Adhesion Testing
In the paint and coating industries, paint adhesion testing is often used to determine if the paint or coating will adhere properly to the substrates to which they are applied. There are several different tests to measure the resistance of paints and coatings from substrates: cross-cut test, scrape adhesion, pull-off test, and others. Scrape Adhesion Test The scrape adhesion test measures the determination of the adhesion of organic coatings when applied to smooth, flat panel surfaces. It is helpful in giving relative ratings for a number of coated panels showing significant differences in adhesion. The materials being tested are applied at uniform thickness to flat panels, mainly some sort of sheet metal. When the materials have dried the adhesion is determined by pressing panels under a rounded stylus that is loaded with increasing amounts of weight until the coating is removed from the substrate surface. Pull-off test The adhesion of a coating or several coated sample of ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Coating
A coating is a covering that is applied to the surface of an object, usually referred to as the Substrate (materials science), substrate. The purpose of applying the coating may be decorative, functional, or both. Coatings may be applied as liquids, gases or solids e.g. Powder coatings. Paints and lacquers are coatings that mostly have dual uses of protecting the substrate and being decorative, although some artists paints are only for decoration, and the paint on large industrial pipes is for preventing corrosion and identification e.g. blue for process water, red for fire-fighting control etc. Functional coatings may be applied to change the surface properties of the substrate, such as adhesion, Wetting, wettability, corrosion resistance, or wear resistance. In other cases, e.g. semiconductor device fabrication (where the substrate is a wafer (electronics), wafer), the coating adds a completely new property, such as a magnetic response or electrical conductivity, and forms an e ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Substrate (building)
The word substrate comes from the Latin '' sub - stratum '' meaning 'the level below' and refers to any material existing or extracted from beneath the topsoil, including sand, chalk and clay. The term is also used for materials used in building foundations or else incorporated into plaster, brick, ceramic and concrete components, which are sometimes called 'filler' products. See also *Firestop *Sealant *Caulking *Paint Paint is any pigmented liquid, liquefiable, or solid mastic composition that, after application to a substrate in a thin layer, converts to a solid film. It is most commonly used to protect, color, or provide texture. Paint can be made in many ... References {{Engineering-stub Civil engineering ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Pull Off Test
The pull-off test, also called stud pull test in which an adhesive connection is made between a stud and the carrier (or object to be tested) by using a glue, possibly an epoxy or polyester resin, that is stronger than the bond that needs to be tested. The force required to pull the stud from the surface, together with the carrier, is Measure (mathematics), measured. Simple mechanical hand-operated loading Tool, equipment has been developed for this purpose. When higher accuracy is required, tests can be performed with more advanced equipment called a bond tester. A bond tester provides more control and possibly automation. Applying the glue automatically and curing with UV light is the next step in automation. This methodology can also be used to measure direct tensile strength or/and the bond strength between two different layers. MIL-STD-883 methods 2011.9 destructive bond pull test and 2031.1 flip chip pull off test apply, as well as JEDEC JESD22-B109. Partial coring may be us ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Tensile Stress
In continuum mechanics, stress is a physical quantity. It is a quantity that describes the magnitude of forces that cause deformation. Stress is defined as ''force per unit area''. When an object is pulled apart by a force it will cause elongation which is also known as deformation, like the stretching of an elastic band, it is called tensile stress. But, when the forces result in the compression of an object, it is called compressive stress. It results when forces like tension or compression act on a body. The greater this force and the smaller the cross-sectional area of the body on which it acts, the greater the stress. Therefore, stress is measured in newton per square meter (N/m2) or pascal (Pa). Stress expresses the internal forces that neighbouring particles of a continuous material exert on each other, while strain is the measure of the deformation of the material. For example, when a solid vertical bar is supporting an overhead weight, each particle in the bar pushes o ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Painter And Decorator
A house painter and decorator is a tradesman responsible for the painting and decorating of buildings, and is also known as a decorator or house painter.''The Modern Painter and Decorator'' volume 1 1921 Caxton The purpose of painting is to improve the appearance of a building and to protect it from damage by water, corrosion, insects and mould. House painting can also be a form of artistic and/or cultural expression such as Ndebele house painting. History of the trade in England In England, little is known of the trade and its structures before the late 13th century, at which point guilds began to form, amongst them the Painters Company and the Stainers Company. These two guilds eventually merged with the consent of the Lord Mayor of the City of London in 1502, forming the Worshipful Company of Painter-Stainers. The guild standardised the craft and acted as a protector of the trade secrets. In 1599, the guild asked Parliament for protection, which was eventually granted in a b ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Coatings
A coating is a covering that is applied to the surface of an object, usually referred to as the substrate. The purpose of applying the coating may be decorative, functional, or both. Coatings may be applied as liquids, gases or solids e.g. Powder coatings. Paints and lacquers are coatings that mostly have dual uses of protecting the substrate and being decorative, although some artists paints are only for decoration, and the paint on large industrial pipes is for preventing corrosion and identification e.g. blue for process water, red for fire-fighting control etc. Functional coatings may be applied to change the surface properties of the substrate, such as adhesion, wettability, corrosion resistance, or wear resistance. In other cases, e.g. semiconductor device fabrication (where the substrate is a wafer), the coating adds a completely new property, such as a magnetic response or electrical conductivity, and forms an essential part of the finished product. A major consideratio ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
