|
Leading Edge
The leading edge of an airfoil surface such as a wing is its foremost edge and is therefore the part which first meets the oncoming air.Crane, Dale: ''Dictionary of Aeronautical Terms, third edition'', page 305. Aviation Supplies & Academics, 1997. Characteristics Sweep Seen in plan the leading edge may be straight, curved, kinked or a combination of these. A straight leading edge may be swept or unswept, while curves or kinks always mean that part of the leading edge is swept. On a swept wing the sweep angle may differ from that of the wing, as wing sweep is conventionally measured at the airfoil 25% chord line. However on a delta wing the leading edge sweep defines the wing sweep. Radius and stagnation point A rounded leading edge helps to maintain a smooth airflow at varying angles of incidence to the airflow. Most subsonic airfoils therefore have a rounded leading edge. The degree of rounding is characterised by the profile radius at that point. The airflow divides to ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Leading Edge
The leading edge of an airfoil surface such as a wing is its foremost edge and is therefore the part which first meets the oncoming air.Crane, Dale: ''Dictionary of Aeronautical Terms, third edition'', page 305. Aviation Supplies & Academics, 1997. Characteristics Sweep Seen in plan the leading edge may be straight, curved, kinked or a combination of these. A straight leading edge may be swept or unswept, while curves or kinks always mean that part of the leading edge is swept. On a swept wing the sweep angle may differ from that of the wing, as wing sweep is conventionally measured at the airfoil 25% chord line. However on a delta wing the leading edge sweep defines the wing sweep. Radius and stagnation point A rounded leading edge helps to maintain a smooth airflow at varying angles of incidence to the airflow. Most subsonic airfoils therefore have a rounded leading edge. The degree of rounding is characterised by the profile radius at that point. The airflow divides to ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Leading Edge Cuff
A leading-edge cuff is a fixed aerodynamics, aerodynamic wing device employed on fixed-wing aircraft to improve the Stall (flight), stall and spin (aerodynamics), spin characteristics. Cuffs may be either factory-designed or an after-market add-on modification.Crane, Dale: ''Dictionary of Aeronautical Terms, third edition'', page 144. Aviation Supplies & Academics, 1997. A leading-edge cuff is a wing leading-edge modification, usually a lightly drooped outboard leading-edge extension. In most cases of outboard leading-edge modification, the wing cuff starts about 50–70% half-span and spans the outer leading edge of the wing. The main goal is to produce a more gradual and gentler stall onset, without any spin departure tendency, particularly where the original wing has a sharp/asymmetric stall behaviour with a passive, non-moving, low-cost device that would have a minimal impact on performance. A further benefit is to lowering stall speed, with lower approach speeds and short ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Vortex Shedding
In fluid dynamics, vortex shedding is an oscillating flow that takes place when a fluid such as air or water flows past a bluff (as opposed to streamlined) body at certain velocities, depending on the size and shape of the body. In this flow, vortices are created at the back of the body and detach periodically from either side of the body forming a Kármán vortex street. The fluid flow past the object creates alternating low-pressure vortices on the downstream side of the object. The object will tend to move toward the low-pressure zone. If the bluff structure is not mounted rigidly and the frequency of vortex shedding matches the resonance frequency of the structure, then the structure can begin to resonate, vibrating with harmonic oscillations driven by the energy of the flow. This vibration is the cause for overhead power line wires humming in the wind, and for the fluttering of automobile whip radio antennas at some speeds. Tall chimneys constructed of thin-walled steel t ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Sailboat
A sailboat or sailing boat is a boat propelled partly or entirely by sails and is smaller than a sailing ship. Distinctions in what constitutes a sailing boat and ship vary by region and maritime culture. Types Although sailboat terminology has varied across history, many terms have specific meanings in the context of modern yachting. A great number of sailboat-types may be distinguished by size, hull configuration, keel type, purpose, number and configuration of masts, and sail plan. Popular monohull designs include: Cutter The cutter is similar to a sloop with a single mast and mainsail, but generally carries the mast further aft to allow for a jib and staysail to be attached to the head stay and inner forestay, respectively. Once a common racing configuration, today it gives versatility to cruising boats, especially in allowing a small staysail to be flown from the inner stay in high winds. Catboat A catboat has a single mast mounted far forward and does not carr ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Vortilon
Vortilons are fixed aerodynamic devices on aircraft wings used to improve handling at low speeds. The vortilon was invented by aerodynamicists working at Douglas Aircraft who had previously developed the engine pylons for the Douglas DC-8. The original pylons which wrapped around the leading edge of the wing had to be cut back to reduce excessive cruise drag. Wind tunnel testing of the next Douglas commercial aircraft, the Douglas DC-9 which had no under-wing engines, showed a cutback engine pylon would be beneficial to wing lift and upwash at the tail at the low speed stall. The pylon was reduced in size and became the vortilon (VORTex-generating-pYLON). Vortilons consist of one or more flat plates attached to the underside of the wing near its leading edge, aligned with the flight direction. When the speed is reduced and the aircraft approaches stall, the local flow at the leading edge is diverted outwards; this spanwise component of velocity around the vortilon creates a vorte ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Stall Strips
A stall strip is a small component fixed to the leading edge of the wing of an airplane to modify its aerodynamic characteristics.Crane, Dale: ''Dictionary of Aeronautical Terms'', third edition, page 487. Aviation Supplies & Academics, 1997. These stall strips may be necessary for the airplane to comply with type certification requirements. A stall strip typically consists of a small piece of material, usually aluminium, triangular in cross section and often 6-12 inches (15–30 cm) in length. It is riveted or bonded to the wing’s leading edge. Some airplanes have one stall strip on each wing. Some airplanes have only one stall strip on one wing. Operation A stall strip initiates flow separation on a region of the upper surface of the wing during flight at high angle of attack. This is typically to avoid a tendency to spin following a stall, or to improve the controllability of the airplane as it approaches the stall. A stall strip may be intended to alter the wing†... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Leading Edge Slot
A leading-edge slot is a fixed aerodynamic feature of the wing of some aircraft to reduce the stall speed and promote good low-speed handling qualities. A leading-edge slot is a spanwise gap in each wing, allowing air to flow from below the wing to its upper surface. In this manner they allow flight at higher angles of attack and thus reduce the stall speed. Purpose and development At an angle of attack above about 15° many airfoils enter the stall. Modification of such an airfoil with a fixed leading-edge slot can increase the stalling angle to between 22° and 25°.Clancy, L.J., ''Aerodynamics'', Section 6.9 Slots were first developed by Handley Page in 1919 and the first aircraft to fly with them was the experimental H.P.17, a modified Airco DH.9A. Their invention is credited jointly to Sir Frederick Handley Page and Gustav Lachmann. The first aircraft fitted with controllable slots was the Handley Page H.P.20. Licensing the design became one of Handley Page's major sou ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Leading Edge Slats
Slats are aerodynamic surfaces on the leading edge of the wing of a fixed-wing aircraft which, when deployed, allow the wing to operate at a higher angle of attack. A higher coefficient of lift is produced as a result of angle of attack and speed, so by deploying slats an aircraft can fly at slower speeds, or take off and land in shorter distances. They are used during takeoff and landing or while performing low speed maneuvers which may take the aircraft close to a stall, they are retracted in normal flight to minimize drag. Slats are one high-lift device used on high speed turbojet aircraft, trailing edge flap systems running along the trailing edge of the wing are common on all aircraft. Types Types include: ;Automatic: The spring-loaded slat lies flush with the wing leading edge, held in place by the force of the air acting on them. As the aircraft slows down, the aerodynamic force is reduced and the springs extend the slats. Sometimes referred to as Handley-Page slat ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Leading Edge Root Extension
A leading-edge extension (LEX) is a small extension to an aircraft wing surface, forward of the leading edge. The primary reason for adding an extension is to improve the airflow at high angle of attack, angles of attack and low airspeeds, to improve handling and delay the stall. A dog tooth can also improve airflow and reduce drag at higher speeds. Leading-edge slat A leading-edge slat is an aerodynamic surface running spanwise just ahead of the wing leading edge. It creates a leading edge slot between the slat and wing which directs air over the wing surface, helping to maintain smooth airflow at low speeds and high angle of attack, angles of attack. This delays the stall (flight), stall, allowing the aircraft to fly at a higher angle of attack. Slats may be made fixed, or retractable in normal flight to minimize drag (physics)#drag in aerodynamics, drag. Dogtooth extension A dogtooth is a small, sharp zig-zag break in the leading edge of a wing. It is usually used on a swe ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Leading-edge Droop Flap
The leading-edge droop flap is a device on the leading edge of aircraft wings designed to improve airflow at high pitch angles (high angle of attack). The droop flap is similar to the leading-edge slat and the Krueger flap, but with the difference that the entire leading edge section rotates downwards, whereas the slat and Krueger flap are panels which move away from the wing leading edge when it is deployed.Norris & Wagner (2005), pp.67-68 Location A leading-edge droop flap comprises the rounded front part of a wing, in movable form. The Airbus A380 has droop flaps between the fuselage and each inboard engine, at the leading edge of the thickest part of each wing. Early variants of the Hawker Siddeley Trident had two droop flaps on the outboard of each wing and a Krueger flap on the section closest to the fuselage. [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Deicing Boot
A deicing boot is a type of ice protection system installed on aircraft surfaces to permit a mechanical deicing in flight. Such boots are generally installed on the leading edges of wings and control surfaces (e.g. horizontal and vertical stabilizer) as these areas are most likely to accumulate ice and any contamination could severely affect the aircraft's performance. Design A deicing boot consists of a thick rubber membrane that is installed over the surface to be deiced. As atmospheric icing occurs and ice builds up, a pneumatic system inflates the boot with compressed air. This expansion in size cracks any ice that has accumulated, and this ice is blown away into the airflow. The boots are then deflated to return the wing or surface to its optimal shape. Boots require proper care. Holes in the boot may create air leaks that will decrease the effectiveness of the boots. As such, boots must be carefully inspected before each flight and any holes or cuts must be patched. ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Leading Edge Extension
A leading-edge extension (LEX) is a small extension to an aircraft wing surface, forward of the leading edge. The primary reason for adding an extension is to improve the airflow at high angles of attack and low airspeeds, to improve handling and delay the stall. A dog tooth can also improve airflow and reduce drag at higher speeds. Leading-edge slat A leading-edge slat is an aerodynamic surface running spanwise just ahead of the wing leading edge. It creates a leading edge slot between the slat and wing which directs air over the wing surface, helping to maintain smooth airflow at low speeds and high angles of attack. This delays the stall, allowing the aircraft to fly at a higher angle of attack. Slats may be made fixed, or retractable in normal flight to minimize drag. Dogtooth extension A dogtooth is a small, sharp zig-zag break in the leading edge of a wing. It is usually used on a swept wing, to generate a vortex flow field to prevent separated flow from progressing o ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
.jpg "Click for more on -> Leading Edge")
