Hot Tube Engine
The hot tube engine is a primitive and long-obsolete type of combustion engine, not to be confused with the hot-bulb engine. The timing of a hot tube engine is controlled by means of varying the length of the hot-tube ignitor, that does the job that a spark plug does in a spark ignited engine. Length of the tube controls when the charge ignites, and the ignition timing can be optimized so as to allow different operating speeds to be selected, much like a spark advance control. It was mostly used as a stationary engine on farms but was also found in very early automobiles and motorcycles. Contrary to the aforementioned hot-bulb engine which only requires a heater to begin combustion but then self-sustains, the flame must be kept on the ignitor tube for the engine to keep working, because the byproduct heat from internal combustion is insufficient to maintain the required temperature for ignition. Modern recreations and restored engines are therefore built to run on propane, as it ... [...More Info...]       [...Related Items...]     OR:     [Wikipedia]   [Google]   [Baidu]   |
|
Hot-bulb Engine
The hot-bulb engine is a type of internal combustion engine in which fuel ignites by coming in contact with a red-hot metal surface inside a bulb, followed by the introduction of air (oxygen) compressed into the hot-bulb chamber by the rising piston. There is some ignition when the fuel is introduced, but it quickly uses up the available oxygen in the bulb. Vigorous ignition takes place only when sufficient oxygen is supplied to the hot-bulb chamber on the compression stroke of the engine. Most hot-bulb engines were produced as one or two-cylinder, low-speed two-stroke crankcase scavenged units. History Four-stroke Hornsby-Akroyd oil engine The concept of this engine was established by Herbert Akroyd Stuart, an English inventor. The first prototypes were built in 1886 and production started in 1891 by Richard Hornsby & Sons of Grantham, Lincolnshire, England under the title Hornsby Akroyd Patent Oil Engine under licence.Herbert Akroyd Stuart, ''Improvements in Engines ... [...More Info...]       [...Related Items...]     OR:     [Wikipedia]   [Google]   [Baidu]   |
|
Hot-tube Ignitor
A hot-tube ignitor was an early device that fit onto the cylinder head of an internal-combustion engine, used to ignite the compressed fuel/air mixture by means of a flame heating part of the tube red-hot. A hot-tube ignitor consisted of a metal or porcelain tube, closed at one end and attached to the cylinder head at the other and an adjustable burner that could be moved to position its flame at any point along the length of the tube. Operation The compression stroke in the cylinder pushed some left over combustion products in the tube, followed by fresh (unburned) fuel/air mixture. When the compression was enough that the fuel reached the red-hot area of the tube, ignition occurred. On early designs, ignition timing was adjusted by adjusting the position of the red-hot spot on the tube—this was accomplished by moving the burner along the length of the tube. Most later styles used a fixed burner and varied tube lengths to change ignition timing. Disadvantages Hot-tube ignitors ... [...More Info...]       [...Related Items...]     OR:     [Wikipedia]   [Google]   [Baidu]   |
|
Spark Plug
A spark plug (sometimes, in British English, a sparking plug, and, colloquially, a plug) is a device for delivering electric current from an ignition system to the combustion chamber of a spark-ignition engine to ignite the compressed fuel/air mixture by an electric spark, while containing combustion pressure within the engine. A spark plug has a metal threaded shell, electrically isolated from a central electrode by a ceramic insulator. The central electrode, which may contain a resistor, is connected by a heavily insulated wire to the output terminal of an ignition coil or magneto. The spark plug's metal shell is screwed into the engine's cylinder head and thus electrically grounded. The central electrode protrudes through the porcelain insulator into the combustion chamber, forming one or more spark gaps between the inner end of the central electrode and usually one or more protuberances or structures attached to the inner end of the threaded shell and designated the ''side ... [...More Info...]       [...Related Items...]     OR:     [Wikipedia]   [Google]   [Baidu]   |
|
Hot-tube Ignitor
A hot-tube ignitor was an early device that fit onto the cylinder head of an internal-combustion engine, used to ignite the compressed fuel/air mixture by means of a flame heating part of the tube red-hot. A hot-tube ignitor consisted of a metal or porcelain tube, closed at one end and attached to the cylinder head at the other and an adjustable burner that could be moved to position its flame at any point along the length of the tube. Operation The compression stroke in the cylinder pushed some left over combustion products in the tube, followed by fresh (unburned) fuel/air mixture. When the compression was enough that the fuel reached the red-hot area of the tube, ignition occurred. On early designs, ignition timing was adjusted by adjusting the position of the red-hot spot on the tube—this was accomplished by moving the burner along the length of the tube. Most later styles used a fixed burner and varied tube lengths to change ignition timing. Disadvantages Hot-tube ignitors ... [...More Info...]       [...Related Items...]     OR:     [Wikipedia]   [Google]   [Baidu]   |