|
Guy (sailing)
A guy (probably from Dutch ''gei'', "brail") is a line (rope) attached to and intended to control the end of a spar on a sailboat. On a modern sloop-rigged sailboat with a symmetric spinnaker, the spinnaker pole is the spar most commonly controlled by one or more guys. Types There are two primary types of guys used to control a spinnaker pole: *The afterguy, working guy, or simply guy and sometimes known as a brace is attached to the windward clew of the spinnaker, and runs through the jaws on the outboard end of the pole and back to the cockpit. The afterguy is used to rotate the outboard end of the pole around the mast in order to optimize the sail's effectiveness, depending on the direction of the wind. Because a spinnaker has two clews, there is always a second line identical to the afterguy attached to the leeward clew of the spinnaker. This is called the sheet and serves a slightly different function. When the boat jibes, the spinnaker pole will be moved from one si ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Cockpit (sailing)
A cockpit is a name for the location of controls of a vessel; while traditionally an open well in the deck of a boat outside any deckhouse or cabin, in modern boats they may refer to an enclosed area. Smaller boats typically have an ''aft cockpit,'' towards the stern of the boat, whereas larger vessels may provide a ''center cockpit'' with greater protection from weather. On a recreational sailboat, the cockpit is considered the most safe external location for crew. A bridge deck is a raised separation between an external cockpit and cabin or saloon, used to keep water from astern from entering from the cockpit, especially in following seas. History In the Royal Navy, the term cockpit originally referred to the area where the coxswain was stationed. This led to the word being used to refer to the area towards the stern of a small decked vessel that houses the rudder controls. The midshipmen and master's mate Master's mate is an obsolete rating which was used by the Royal Navy, ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Bracing (aeronautics)
In aeronautics, bracing comprises additional structural members which stiffen the functional airframe to give it rigidity and strength under load. Bracing may be applied both internally and externally, and may take the form of strut, which act in compression or tension as the need arises, and/or wires, which act only in tension. In general, bracing allows a stronger, lighter structure than one which is unbraced, but external bracing in particular adds drag which slows down the aircraft and raises considerably more design issues than internal bracing. Another disadvantage of bracing wires is that they require routine checking and adjustment, or rigging, even when located internally. During the early years of aviation, bracing was a universal feature of all forms of aeroplane, including the monoplanes and biplanes which were then equally common. Today, bracing in the form of lift struts is still used for some light commercial designs where a high wing and light weight are more impo ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Guy-wire
A guy-wire, guy-line, guy-rope, or stay, also called simply a guy, is a tensioned cable designed to add stability to a free-standing structure. They are used commonly for ship masts, radio masts, wind turbines, utility poles, and tents. A thin vertical mast supported by guy wires is called a guyed mast. Structures that support antennas are frequently of a lattice construction and are called "towers". One end of the guy is attached to the structure, and the other is anchored to the ground at some distance from the mast or tower base. The tension in the diagonal guy-wire, combined with the compression and buckling strength of the structure, allows the structure to withstand lateral loads such as wind or the weight of cantilevered structures. They are installed radially, usually at equal angles about the structure, in trios and quads. As the tower leans a bit due to the wind force, the increased guy tension is resolved into a compression force in the tower or mast and a late ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Downhaul
The downhaul is a line which is part of the rigging on a sailboat; it applies downward force on a spar or sail. The most common downhaul on a modern sailboat is attached to the spinnaker pole, though this may be referred to as the foreguy in some rigging nomenclature. The term is also commonly applied to the cunningham on the mainsail. In a windsurfing rig, the downhaul is the primary load-bearing line which controls the sail's shape. Modern windsurfing sails incorporate a sleeve for the mast, and therefore do not have a halyard In sailing, a halyard or halliard is a line (rope) that is used to hoist a ladder, sail, flag or yard. The term ''halyard'' comes from the phrase "to haul yards". Halyards, like most other parts of the running rigging, were classically made of ... which tensions the top of the sail. The downhaul is tensioned early in the rigging process and is generally not adjustable on the water, and is therefore rather different in use than the downhaul on a sailb ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Jibe (sailing)
A jibe (US) or gybe (Britain) is a sailing maneuver whereby a sailing vessel reaching downwind turns its stern through the wind, which then exerts its force from the opposite side of the vessel. Because the mainsail boom can swing across the cockpit quickly, jibes are potentially dangerous to person and rigging compared to tacking. Therefore accidental jibes are to be avoided while the proper technique must be applied so as to control the maneuver. For square-rigged ships, this maneuver is called wearing ship. In this maneuver, the mainsail will cross the center of the boat while the jib is pulled to the other side of the boat. If a spinnaker is up, its pole will have to be manually moved to the other side, to remain opposite the mainsail. In a dinghy, raising the centerboard can increase the risk of capsizing during what can be a somewhat violent maneuver, although the opposite is true of a dinghy with a flat, planing hull profile: raising the centerboard reduces hee ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Sheet (sailing)
In sailing, a sheet is a line (rope, cable or chain) used to control the movable corner(s) (clews) of a sail. Terminology In nautical usage the term "sheet" is applied to a line or chain attached to the lower corners of a sail for the purpose of extension or change of direction. The connection in derivation with the root "shoot" is more clearly seen in "sheet-anchor", one that is kept in reserve, to be "shot" in case of emergency. Fore-and-aft rigs Fore-and-aft rigs comprise the vast majority of sailing vessels in use today, including effectively all dinghies and yachts. The sheet on a fore-and-aft sail controls the angle of the sail to the wind, and should be adjusted to keep the sail just filled. Most smaller boats use the Bermuda rig, which has two or three sets of sheets: * The mainsheet is attached to the boom, and is used to control the mainsail. In a rig with no boom on the mainsail, the mainsheet would attach directly to the mainsail clew. A mainsheet is a line c ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Leeward
Windward () and leeward () are terms used to describe the direction of the wind. Windward is ''upwind'' from the point of reference, i.e. towards the direction from which the wind is coming; leeward is ''downwind'' from the point of reference, i.e. along the direction towards which the wind is going. The side of a ship that is towards the leeward is its "lee side". If the vessel is heeling under the pressure of crosswind, the lee side will be the "lower side". During the Age of Sail, the term ''weather'' was used as a synonym for ''windward'' in some contexts, as in the ''weather gage''. Because it captures rain, the windward side of a mountain tends to be wet compared to the leeward it blocks. Origin The term "lee" comes from the middle-low German word // meaning "where the sea is not exposed to the wind" or "mild". The terms Luv and Lee (engl. Windward and Leeward) have been in use since the 17th century. Usage Windward and leeward directions (and the points ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Parts Of A Sail
Sail components include the features that define a sail's shape and function, plus its constituent parts from which it is manufactured. A sail may be classified in a variety of ways, including by its orientation to the vessel (e.g. ''fore-and-aft'') and its shape, (e.g. ''(a)symmetrical'', ''triangular'', ''quadrilateral'', etc.). Sails are typically constructed out of flexible material that is shaped by various means, while in use, to offer an appropriate airfoil, according to the strength and apparent direction of the wind. A variety of features and fittings allow the sail to be attached to lines and spars. Whereas conventional sails form an airfoil with one layer of fabric, wingsails comprise a structure that has material on both sides to form an airfoil—much like a wing placed vertically on the vessel—and are beyond the scope of this article. Classifications Sails may be classified as either ''triangular'', which describes sails that either come to one point of suspen ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Dutch Language
Dutch ( ) is a West Germanic language spoken by about 25 million people as a first language and 5 million as a second language. It is the third most widely spoken Germanic language, after its close relatives German and English. ''Afrikaans'' is a separate but somewhat mutually intelligible daughter languageAfrikaans is a daughter language of Dutch; see , , , , , . Afrikaans was historically called Cape Dutch; see , , , , , . Afrikaans is rooted in 17th-century dialects of Dutch; see , , , . Afrikaans is variously described as a creole, a partially creolised language, or a deviant variety of Dutch; see . spoken, to some degree, by at least 16 million people, mainly in South Africa and Namibia, evolving from the Cape Dutch dialects of Southern Africa. The dialects used in Belgium (including Flemish) and in Suriname, meanwhile, are all guided by the Dutch Language Union. In Europe, most of the population of the Netherlands (where it is the only official language spoken country ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Spinnaker Pole
A spinnaker pole is a spar used in sailboats (both dinghys and yachts) to help support and control a variety of headsails, particularly the spinnaker. However, it is also used with other sails, such as genoas and jibs, when sailing downwind with no spinnaker hoisted. (Since the load on a spinnaker pole is very light on this point of sailing, sometimes a special light spinnaker pole called a whisker pole is used in these circumstances.) The spinnaker pole is rigged to run from the base of the mast, where there is a special fitting for attaching one end of the pole, out to windward over the side of the boat. There, one of the control lines of whichever sail it is to be used with is run through a fitting on the other end of the spinnaker pole. This allows for more precise control of the corner of the sail to which the line is attached. For a spinnaker, the line attached to the pole is the guy, or brace, and the corner is the tack. For other headsails, such as a jib, the line would ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Spinnaker
A spinnaker is a sail designed specifically for sailing off the wind on courses between a reach (wind at 90° to the course) to downwind (course in the same direction as the wind). Spinnakers are constructed of lightweight fabric, usually nylon, and are often brightly colored. They may be designed to perform best as either a reaching or a running spinnaker, by the shaping of the panels and seams. They are attached at only three points and said to be ''flown''. Nomenclature Informal names for a spinnaker are ''kite'' or ''chute'' (owing to their resemblance to a parachute in both construction and appearance). Boats may have more than one spinnaker, differentiated by a letter to indicate symmetric (S) or asymmetric (A) and a number to indicate size (with higher numbers indicating smaller size), e.g. ''A1'' would be a large asymmetric sail and ''S3'' would be a smaller symmetric sail. Operation A spinnaker is used for sailing with the direction of the wind. Symmetrical ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
