|
Electronic Brake Force Distribution
Electronic brakeforce distribution (EBD or EBFD) or electronic brakeforce limitation (EBL) is an automobile brake technology that automatically varies the amount of force applied to each of a vehicle's wheels, based on road conditions, speed, loading, etc, thus providing intelligent control of both brake balance and overall brake force. Always coupled with anti-lock braking systems (ABS), EBD can apply more or less braking pressure to each wheel in order to maximize stopping power whilst maintaining vehicular control. Typically, the front end carries more weight and EBD distributes less braking pressure to the rear brakes so the rear brakes do not lock up and cause a skid. In some systems, EBD distributes more braking pressure at the rear brakes during initial brake application before the effects of weight transfer become apparent. ABS Vehicle wheels may lock-up due to excessive wheel torque over tire–road friction forces available, caused by too much hydraulic line pressure. Th ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Brake
A brake is a mechanical device that inhibits motion by absorbing energy from a moving system. It is used for slowing or stopping a moving vehicle, wheel, axle, or to prevent its motion, most often accomplished by means of friction. Background Most brakes commonly use friction between two surfaces pressed together to convert the kinetic energy of the moving object into heat, though other methods of energy conversion may be employed. For example, regenerative braking converts much of the energy to electrical energy, which may be stored for later use. Other methods convert kinetic energy into potential energy in such stored forms as pressurized air or pressurized oil. Eddy current brakes use magnetic fields to convert kinetic energy into electric current in the brake disc, fin, or rail, which is converted into heat. Still other braking methods even transform kinetic energy into different forms, for example by transferring the energy to a rotating flywheel. Brakes are generally ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Force
In physics, a force is an influence that can change the motion of an object. A force can cause an object with mass to change its velocity (e.g. moving from a state of rest), i.e., to accelerate. Force can also be described intuitively as a push or a pull. A force has both magnitude and direction, making it a vector quantity. It is measured in the SI unit of newton (N). Force is represented by the symbol (formerly ). The original form of Newton's second law states that the net force acting upon an object is equal to the rate at which its momentum changes with time. If the mass of the object is constant, this law implies that the acceleration of an object is directly proportional to the net force acting on the object, is in the direction of the net force, and is inversely proportional to the mass of the object. Concepts related to force include: thrust, which increases the velocity of an object; drag, which decreases the velocity of an object; and torque, which produce ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Brake Balance
The brake balance or brake bias of a vehicle is the distribution of brake force at the front and rear tires, and may be given as the percentage distributed to the front brakes (e.g. 52%) or as the ratio of front and rear percentages (e.g. 52/48). The braking balance affects the driving characteristics in terms of how fast the vehicle can brake, how the vehicle can take corners, and tire wear. The optimal brake balance can vary between circuits, weather conditions and driving styles. On race cars, the brake balance is often part of the racing setup, and in formula car racing it is regularly adjusted during the course of an entire lap. In some cases, the brake balance may be adjusted to match the traction (grip) of the vehicle during braking, which usually means distributing a greater braking force to the front (for example 55/45). In other cases, it may be desirable for the brake balance to be the more similar at the front and rear (e.g. 50/50) for the tires to last longer, which may ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Anti-lock Braking System
An anti-lock braking system (ABS) is a safety anti-skid braking system used on aircraft and on land vehicles, such as cars, motorcycles, trucks, and buses. ABS operates by preventing the wheels from locking up during braking, thereby maintaining tractive contact with the road surface and allowing the driver to maintain more control over the vehicle. ABS is an automated system that uses the principles of threshold braking and cadence braking, techniques which were once practiced by skillful drivers before ABS was widespread. ABS operates at a much faster rate and more effectively than most drivers could manage. Although ABS generally offers improved vehicle control and decreases stopping distances on dry and some slippery surfaces, on loose gravel or snow-covered surfaces ABS may significantly increase braking distance, while still improving steering control. Since ABS was introduced in production vehicles, such systems have become increasingly sophisticated and effective. Mode ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Weight Transfer
Weight transfer and load transfer are two expressions used somewhat confusingly to describe two distinct effects: *the change in load borne by different wheels of even perfectly rigid vehicles during acceleration *the change in center of mass (CoM) location relative to the wheels because of suspension compliance or cargo shifting or sloshing In the automobile industry, weight transfer customarily refers to the change in load borne by different wheels during acceleration. This would be more properly referred to as load transfer, and that is the expression used in the motorcycle industry, while weight transfer on motorcycles, to a lesser extent on automobiles, and cargo movement on either is due to a change in the CoM location relative to the wheels. This article uses this latter pair of definitions. Load transfer In wheeled vehicles, load transfer is the measurable change of load borne by different wheels during acceleration (both longitudinal and lateral). This includes bra ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Electronic Stability Control
Electronic stability control (ESC), also referred to as electronic stability program (ESP) or dynamic stability control (DSC), is a computerized technology that improves a vehicle's stability by detecting and reducing loss of traction ( skidding). When ESC detects loss of steering control, it automatically applies the brakes to help steer the vehicle where the driver intends to go. Braking is automatically applied to wheels individually, such as the outer front wheel to counter oversteer, or the inner rear wheel to counter understeer. Some ESC systems also reduce engine power until control is regained. ESC does not improve a vehicle's cornering performance; instead, it helps reduce the chance of the driver losing control of the vehicle. According to the U.S. National Highway Traffic Safety Administration and the Insurance Institute for Highway Safety in 2004 and 2006 respectively, one-third of fatal accidents could be prevented by the use of the technology. In Europe the elect ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Yaw Rate Sensor
A yaw-rate sensor is a gyroscopic device that measures a vehicle's yaw rate, its angular velocity around its vertical axis. The angle between the vehicle's heading and velocity is called its slip angle, which is related to the yaw rate. Types There are two types of yaw-rate sensors: the piezoelectric type and the micromechanical type. In the piezoelectric type, the sensor is a "tuning fork"-shaped structure with four piezoelectric elements, two on top and two below. When the slip angle is zero (i.e., no slip), the upper elements produce no voltage as no Coriolis force acts on them. But when cornering, the rotational movement causes the upper part of the tuning fork to leave the oscillatory plane, creating an alternating voltage (and thus an alternating current) proportional to the yaw rate and oscillatory speed. The output signal's sign depends on the direction of rotation. In the micromechanical type, the Coriolis acceleration is measured by a micromechanical capacitive acce ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Center Of Gravity
In physics, the center of mass of a distribution of mass in space (sometimes referred to as the balance point) is the unique point where the weight function, weighted relative position (vector), position of the distributed mass sums to zero. This is the point to which a force may be applied to cause a linear acceleration without an angular acceleration. Calculations in mechanics are often simplified when formulated with respect to the center of mass. It is a hypothetical point where the entire mass of an object may be assumed to be concentrated to visualise its motion. In other words, the center of mass is the particle equivalent of a given object for application of Newton's laws of motion. In the case of a single rigid body, the center of mass is fixed in relation to the body, and if the body has uniform density, it will be located at the centroid. The center of mass may be located outside the physical body, as is sometimes the case for wikt:hollow, hollow or open-shaped object ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Understeer And Oversteer
Understeer and oversteer are vehicle dynamics terms used to describe the sensitivity of a vehicle to steering. Oversteer is what occurs when a car turns (steers) by more than the amount commanded by the driver. Conversely, understeer is what occurs when a car steers less than the amount commanded by the driver. Automotive engineers define understeer and oversteer based on changes in steering angle associated with changes in lateral acceleration over a sequence of steady-state circular turning tests. Car and motorsport enthusiasts often use the terminology more generally in magazines and blogs to describe vehicle response to steering in a variety of maneuvers. Vehicle dynamics terminology Standard terminology used to describe understeer and oversteer are defined by the Society of Automotive Engineers (SAE) in document J670SAE International Surface Vehicle Recommended Practice, "Vehicle Dynamics Terminology", SAE Standard J670, Rev. 2008-01-24 and by the International Organization ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Brake Assist
Brake assist (BA or BAS) or emergency brake assist (EBA) is a term for an automobile braking technology that increases braking pressure in an emergency. The first application was developed jointly by Daimler-Benz and TRW/ LucasVarity. Research conducted in 1992 at the Mercedes-Benz driving simulator in Berlin revealed that more than 90% of drivers fail to brake with enough force when faced with an emergency. By interpreting the speed and force with which the brake pedal is pushed, the system detects if the driver is trying to execute an emergency stop, and if the brake pedal is not fully applied, the system overrides and fully applies the brakes until the anti-lock braking system (ABS) takes over to stop the wheels locking up. This is a lower level of automation than advanced emergency braking which is a collision avoidance system, which may initiate braking on its own if the onboard computer detects an imminent collision. Overview Many drivers are not prepared for the relat ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Cornering Brake Control
Cornering brake control (CBC) is an automotive safety system introduced by carmakers BMW and Mercedes-Benz (ESP Dynamic Cornering Assist and Curve Dynamic Assist). It is a further development and expansion of the anti-lock braking system, designed to distribute braking force by adjusting the brake balance during braking whilst cornering. It works by applying braking pressure asymmetrically despite physically difficult conditions (e.g. the car swerving towards the inside of the bend when the wheel load changes). By asymmetrically distributing brake pressure to the left- and right-side brakes or by reducing pressure (to the rear axle), even if the driver brakes outside the normal range of ABS.Cornering Brake Control http://www.bmw.com/com/en/insights/technology/technology_guide/articles/cornering_brake_control.html?source=index&article=cornering_brake_control See also * Anti-lock braking system (ABS) * Electronic brakeforce distribution (EBD) * Electronic stability control (ESC), ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Automobile Safety
Automotive safety is the study and practice of design, construction, equipment and regulation to minimize the occurrence and consequences of traffic collisions involving motor vehicles. Road traffic safety more broadly includes roadway design. One of the first formal academic studies into improving motor vehicle safety was by Cornell Aeronautical Laboratory of Buffalo, New York. The main conclusion of their extensive report is the crucial importance of seat belts and padded dashboards. However, the primary vector of traffic-related deaths and injuries is the disproportionate mass and velocity of an automobile compared to that of the predominant victim, the pedestrian. According to the World Health Organization (WHO), 80% of cars sold in the world are not compliant with main safety standards. Only 40 countries have adopted the full set of the seven most important regulations for car safety. In the United States, a pedestrian is injured by a motor vehicle every 8 minutes, and ar ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
