|
Balanced Circuit
A balanced circuit is circuitry for use with a balanced line or the balanced line itself. Balanced lines are a common method of transmitting many types of electrical communication signals between two points on two wires. In a balanced line the two signal lines are of a matched impedance to help ensure that interference induced in the line is common-mode and can be removed at the receiving end by circuitry with good common-mode rejection. To maintain the balance, circuit blocks which interface to the line, or are connected in the line, must also be balanced. Balanced lines work because the interfering noise from the surrounding environment induces equal noise voltages into both wires. By measuring the voltage difference between the two wires at the receiving end, the original signal is recovered while the noise is rejected. Any inequality in the noise induced in each wire is an imbalance and will result in the noise not being fully rejected. One requirement for balance is that ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Electronic Circuit
An electronic circuit is composed of individual electronic components, such as resistors, transistors, capacitors, inductors and diodes, connected by conductive wires or traces through which electric current can flow. It is a type of electrical circuit and to be referred to as ''electronic'', rather than ''electrical'', generally at least one active component must be present. The combination of components and wires allows various simple and complex operations to be performed: signals can be amplified, computations can be performed, and data can be moved from one place to another. Circuits can be constructed of discrete components connected by individual pieces of wire, but today it is much more common to create interconnections by photolithographic techniques on a laminated substrate (a printed circuit board or PCB) and solder the components to these interconnections to create a finished circuit. In an integrated circuit or IC, the components and interconnections are formed on t ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Impedance Balance
Impedance is the complex-valued generalization of resistance. It may refer to: *Acoustic impedance, a constant related to the propagation of sound waves in an acoustic medium *Electrical impedance, the ratio of the voltage phasor to the electric current phasor, a measure of the opposition to time-varying electric current in an electric circuit **High impedance, when only a small amount of current is allowed through **Characteristic impedance of a transmission line **Impedance (accelerator physics), a characterization of the self interaction of a charged particle beam **Nominal impedance, approximate designed impedance **Impedance matching, the adjustment of input impedance and output impedance *Mechanical impedance, a measure of opposition to motion of a structure subjected to a force *Wave impedance, a constant related to electromagnetic wave propagation in a medium **Impedance of free space The impedance of free space, , is a physical constant relating the magnitudes of the elec ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Phone Connector (audio)
A phone connector, also known as phone jack, audio jack, headphone jack or jack plug, is a family of electrical connectors typically used for analog signal, analog audio signals. A plug, the Gender of connectors and fasteners, male connector, is inserted into the jack, the female connector. The phone connector was invented for use in telephone switchboards in the 19th century and is still widely used. The phone connector is cylindrical in shape, with a grooved tip to retain it. In its original audio configuration, it typically has two, three, four or, occasionally, five contacts. Three-contact versions are known as ''TRS connectors'', where ''T'' stands for Tip and ring, "tip", ''R'' stands for Tip and ring, "ring" and ''S'' stands for "sleeve". Ring contacts are typically the same diameter as the sleeve, the long shank. Similarly, two-, four- and five-contact versions are called ''TS'', ''TRRS'' and ''TRRRS connectors'' respectively. The outside diameter of the "sleeve" c ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Professional Audio
Professional audio, abbreviated as pro audio, refers to both an activity and a category of high quality, studio-grade audio equipment. Typically it encompasses sound recording, sound reinforcement system setup and audio mixing, and studio music production by trained sound engineers, audio engineers, record producers, and audio technicians who work in live event support and recording using mixing consoles, recording equipment and sound reinforcement systems. Professional audio is differentiated from consumer- or home-oriented audio, which are typically geared toward listening in a non-commercial environment. Professional audio can include, but is not limited to broadcast radio, audio mastering in a recording studio, television studio, and sound reinforcement such as a live concert, DJ performances, audio sampling, public address system set up, sound reinforcement in movie theatres, and design and setup of piped music in hotels and restaurants. Professional audio equipment ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
XLR Connector
The XLR connector is a type of electrical connector primarily used in professional audio, video, and stage lighting equipment. XLR connectors are cylindical in design, and have three to seven connector pins, and are often employed for analog balanced audio interconnections, AES3 digital audio, portable intercom, DMX512 lighting control, and for low-voltage power supply. XLR connectors are included to the international standard for dimensions, IEC 61076-2-103. The XLR connector is superficially similar to the smaller DIN connector, with which it is physically incompatible. History and manufacturers The XLR connector (also Cannon plug and Cannon connector) was invented by James H. Cannon, founder of the Cannon Electric company, Los Angeles, California. The XLR connector originated from the ''Cannon X'' series of connectors in 1915; by 1950, a latching mechanism was added to the connector, which produced the ''Cannon XL'' model of connector, and by 1955, the female connector ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Modular Connector
A modular connector is a type of electrical connector for cords and cables of electronic devices and appliances, such as in computer networking, telecommunication equipment, and audio headsets. Modular connectors were originally developed for use on specific Bell System telephone sets in the 1960s, and similar types found use for simple interconnection of customer-provided telephone subscriber premises equipment to the telephone network. The Federal Communications Commission (FCC) mandated in 1976 an interface registration system, in which they became known as registered jacks. The convenience of prior existence for designers and ease of use led to a proliferation of modular connectors for many other applications. Many applications that originally used bulkier, more expensive connectors have converted to modular connectors. Probably the best-known applications of modular connectors are for telephone and Ethernet. Accordingly, various electronic interface specifications exist ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Autotransformer
An autotransformer is an electrical transformer with only one winding. The "auto" (Greek for "self") prefix refers to the single coil acting alone, not to any kind of automatic mechanism. In an autotransformer, portions of the same winding act as both the primary winding and secondary winding sides of the transformer. In contrast, an ordinary transformer has separate primary and secondary windings which have no metallic conducting path between them. The autotransformer winding has at least three taps where electrical connections are made. Since part of the winding does "double duty", autotransformers have the advantages of often being smaller, lighter, and cheaper than typical dual-winding transformers, but the disadvantage of not providing electrical isolation between primary and secondary circuits. Other advantages of autotransformers include lower leakage reactance, lower losses, lower excitation current, and increased VA rating for a given size and mass. An example of an ap ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Opto-isolator
An opto-isolator (also called an optocoupler, photocoupler, or optical isolator) is an electronic component that transfers electrical Signal, signals between two isolated circuits by using light. Opto-isolators prevent high voltages from affecting the system receiving the signal.Lee et al., p. 2. Commercially available opto-isolators withstand input-to-output voltages up to 10 Volt, kVHasse, p. 145. and voltage transients with speeds up to 25 kV/microsecond, μs.Joffe and Kai-Sang Lock, p. 279. A common type of opto-isolator consists of an Light emitting diode, LED and a phototransistor in the same opaque package. Other types of source-sensor combinations include LED-photodiode, LED-thyristor#photothyristors, LASCR, and lamp (electrical component), lamp-photoresistor pairs. Usually opto-isolators transfer digital (on-off) signals, but some techniques allow them to be used with analog signals. History The value of optically coupling a solid state light emitter to a semi ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Op-amp
An operational amplifier (often op amp or opamp) is a DC-coupled high-gain electronic voltage amplifier with a differential input and, usually, a single-ended output. In this configuration, an op amp produces an output potential (relative to circuit ground) that is typically 100,000 times larger than the potential difference between its input terminals. The operational amplifier traces its origin and name to analog computers, where they were used to perform mathematical operations in linear, non-linear, and frequency-dependent circuits. The popularity of the op amp as a building block in analog circuits is due to its versatility. By using negative feedback, the characteristics of an op-amp circuit, its gain, input and output impedance, bandwidth etc. are determined by external components and have little dependence on temperature coefficients or engineering tolerance in the op amp itself. Op amps are used widely in electronic devices today, including a vast array of consumer, ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Two-wire Circuit
In telecommunication, a two-wire circuit is characterized by supporting transmission in two directions simultaneously, as opposed to four-wire circuits, which have separate pairs for transmit and receive. The subscriber local loop from the telco central office are almost all two wire for analog baseband voice calls (and some digital services like ISDN), and converted to four-wire at the line card back when telephone switching was performed on baseband audio. Today the audio is digitized and processed completely in the digital domain upstream from the local loop. The reason for using two wires rather than four is simple economics—half the materials cost half as much to purchase and install. Note the use of the past-tense "cost," as installation of two-wire copper local loops for telephony was done primarily during the mid 20th century. In the first world there is no new infrastructure planning for new copper-based technology, and as customers are migrating to cellular telephony an ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Center Tap
In electronics, a center tap (CT) is a contact made to a point halfway along a winding of a transformer or inductor, or along the element of a resistor or a potentiometer. Taps are sometimes used on inductors for the coupling of signals, and may not necessarily be at the half-way point, but rather, closer to one end. A common application of this is in the Hartley oscillator. Inductors with taps also permit the transformation of the amplitude of alternating current (AC) voltages for the purpose of power conversion, in which case, they are referred to as autotransformers, since there is only one winding. An example of an autotransformer is an automobile ignition coil. Potentiometer tapping provides one or more connections along the device's element, along with the usual connections at each of the two ends of the element, and the slider connection. Potentiometer taps allow for circuit functions that would otherwise not be available with the usual construction of just the two end ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Ground Loop (electricity)
In an electrical system, a ground loop or earth loop occurs when two points of a circuit are intended to have the same ground reference potential but instead have a different potential between them. This is typically caused when enough current is flowing in the connection between the two ground points to produce a voltage drop and cause two points to be at different potentials. Current may be produced in a circular ground connection (ground loop) by electromagnetic induction. Ground loops are a major cause of noise, hum, and interference in audio, video, and computer systems. Wiring practices that protect against ground loops include ensuring that all vulnerable signal circuits are referenced to one point as ground. The use of differential signaling can provide rejection of ground-induced interference. Removal of safety ground connections to equipment in an effort to eliminate ground loops also eliminates the protection the safety ground connection is intended to provide. ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
