|
BMW M50
The BMW M50 is a straight-6 DOHC petrol engine which was produced from 1990 to 1996. It was released in the E34 520i and 525i, to replace the M20 engine. In September 1992, the M50 was upgraded to the M50TU ("technical update"), which was BMW's first engine to use variable valve timing. Called single VANOS by BMW, the system adjusted the phasing of the intake camshaft. The M50 began to be phased out following the introduction of the M52 engine in 1994. The E36 M3 is powered by the S50 engine series, which is a high output version of the M50. Design A significant advance over its M20 predecessor, the M50 features dual overhead camshaft (DOHC) with four valves per cylinder (the M20 has a single overhead camshaft with 2 valves per cylinder), coil-on-plug ignition, a knock sensor and a lightweight plastic intake manifold. Both engines use an iron block with an aluminum alloy head. The redline is 6,500 rpm for the M50B25 and 6,750 rpm for the M50B20 (7,000&nb ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Straight-six Engine
The straight-six engine (also referred to as an inline-six engine; abbreviated I6 or L6) is a piston engine with six cylinders arranged in a straight line along the crankshaft. A straight-six engine has perfect primary and secondary engine balance, resulting in fewer vibrations than other designs of six or less cylinders. Until the mid-20th century, the straight-six layout was the most common design for engines with six cylinders. However, V6 engines became more common from the 1960s and by the 2000s most straight-six engines had been replaced by V6 engines. An exception to this trend is BMW which has produced automotive straight-six engines from 1933 to the present day. Characteristics In terms of packaging, straight-six engines are almost always narrower than a V6 engine or V8 engine, but longer than straight-four engines, V6s, and most V8s. Straight-six engines are typically produced in displacements ranging from , however engines ranging in size from the Benelli 75 ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Intake Manifold
In automotive engineering, an inlet manifold or intake manifold (in American English) is the part of an engine that supplies the fuel/ air mixture to the cylinders. The word ''manifold'' comes from the Old English word ''manigfeald'' (from the Anglo-Saxon ''manig'' anyand ''feald'' epeatedly and refers to the multiplying of one (pipe) into many.manifold, (adv.) "in the proportion of many to one, by many times". AD1526 ''Oxford English Dictionary'', In contrast, an exhaust manifold collects the exhaust gases from multiple cylinders into a smaller number of pipes – often down to one pipe. The primary function of the intake manifold is to ''evenly'' distribute the combustion mixture (or just air in a direct injection engine) to each intake port in the cylinder head(s). Even distribution is important to optimize the efficiency and performance of the engine. It may also serve as a mount for the carburetor, throttle body, fuel injectors and other components of the engine. ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Motronic
Motronic is the trade name given to a range of digital engine control units developed by Robert Bosch GmbH (commonly known as Bosch) which combined control of fuel injection and ignition in a single unit. By controlling both major systems in a single unit, many aspects of the engine's characteristics (such as power, fuel economy, drivability, and emissions) can be improved. Motronic 1.x Motronic M1.x is powered by various i8051 derivatives made by Siemens, usually SAB80C515 or SAB80C535. Code/data is stored in DIL or PLCC EPROM and ranges from 32k to 128k. 1.0 Often known as "Motronic basic", Motronic ML1.x was one of the first digital engine-management systems developed by Bosch. These early Motronic systems integrated the spark timing element with then-existing Jetronic fuel injection technology. It was originally developed and first used in the BMW 7 Series, before being implemented on several Volvo and Porsche engines throughout the 1980s. The components of the Motronic M ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Throttle
A throttle is the mechanism by which fluid flow is managed by constriction or obstruction. An engine's power can be increased or decreased by the restriction of inlet gases (by the use of a throttle), but usually decreased. The term ''throttle'' has come to refer, informally, to any mechanism by which the power or speed of an engine is regulated, such as a car's accelerator pedal. What is often termed a ''throttle'' (in an aviation context) is also called a thrust lever, particularly for jet engine powered aircraft. For a steam locomotive, the valve which controls the steam is known as the regulator. Internal combustion engines In an internal combustion engine, the throttle is a means of controlling an engine's power by regulating the amount of fuel or air entering the engine. In a motor vehicle the control used by the driver to regulate power is sometimes called the throttle, accelerator, or gas pedal. For a gasoline engine, the throttle most commonly regulates the am ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
BMW S14
The BMW S14 is a DOHC four-cylinder petrol engine which was used in the E30 M3, E30 320iS, and E36 320i Super Touring. It is based on the BMW M10 block and the cylinder head from the six-cylinder BMW S38 with two cylinders removed. The direct successor to the S14 was the S42 based on the M42 engine. The S42 was a racing engine installed in the E36 320i for the German Super Tourenwagen Cup. There is no direct successor to the S14 for production BMWs, since the following generation of M3 is powered by the BMW S50 six-cylinder engine. Two separate throttle bodies are used, each incorporating two throttle butterfly plates. Versions S14B20 This version was only sold in Portugal and Italy. It has a displacement reduced to by shortening the stroke to . Applications: * 1987-1990 E30 320iS (Italy and Portugal only) S14B23 The E30 M3 was initially released with the S14B23 engine. Versions equipped with a catalytic converter produced and 230 Nm. In April 1989, the Ravaglia ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Petrol Engine
A petrol engine (gasoline engine in American English) is an internal combustion engine designed to run on petrol (gasoline). Petrol engines can often be adapted to also run on fuels such as liquefied petroleum gas and ethanol blends (such as ''E10'' and ''E85''). Most petrol engines use spark ignition, unlike diesel engines which typically use compression ignition. Another key difference to diesel engines is that petrol engines typically have a lower compression ratio. Design Thermodynamic cycle Most petrol engines use either the four-stroke Otto cycle or the two-stroke cycle. Petrol engines have also been produced using the Miller cycle and Atkinson cycle. Layout Most petrol-powered piston engines are straight engines or V engines. However, flat engines, W engines and other layouts are sometimes used. Wankel engines are classified by the number of rotors used. Compression ratio Cooling Petrol engines are either air-cooled or water-cooled. Igniti ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
BMW M54
The BMW M54 is a naturally aspirated straight-6 petrol engine produced from 2000 to 2006. It was released in the E53 X5 and is the replacement for the M52 engine. The S54 is the equivalent high performance engine, used in the E46 M3, the Z3 M Coupé/Roadster and the E85/E86 Z4 M. The BMW M56 SULEV engine (sold in several states of the United States) is based on the M54. The M54 was phased out following the introduction of the BMW N52 engine in 2004. From 2001 to 2003, the M54 was included on the Ward's 10 Best Engines list. Design Compared with the final versions of its M52 predecessor (called the 'M52TU'), the M54 has a non-return fuel system, a fully electronic throttle (without mechanical backup), Siemens MS 43 engine management, a revised intake manifold. The displacement of the largest variant increased from 2.8 L to , due to an increase in stroke to . As per the M52TU, the M54 uses an aluminium block and aluminium cylinder head with cast iron cylinder liners. Varia ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Overhead Camshaft
An overhead camshaft (OHC) engine is a piston engine where the camshaft is located in the cylinder head above the combustion chamber. This contrasts with earlier overhead valve engines (OHV), where the camshaft is located below the combustion chamber in the engine block. ''Single overhead camshaft'' (SOHC) engines have one camshaft per bank of cylinders. ''Dual overhead camshaft'' (DOHC, also known as "twin-cam".) engines have two camshafts per bank. The first production car to use a DOHC engine was built in 1910. Use of DOHC engines slowly increased from the 1940s, leading to many automobiles by the early 2000s using DOHC engines. Design In an OHC engine, the camshaft is located at the top of the engine, above the combustion chamber. This contrasts the earlier overhead valve engine (OHV) and flathead engine configurations, where the camshaft is located down in the engine block. The valves in both OHC and OHV engines are located above the combustion chamber; however an OHV ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Stroke (engine)
In the context of an internal combustion engine, the term stroke has the following related meanings: * A phase of the engine's cycle (e.g. compression stroke, exhaust stroke), during which the piston travels from top to bottom or vice versa. * The type of power cycle used by a piston engine (e.g. two-stroke engine, four-stroke engine). * "Stroke length", the distance travelled by the piston during each cycle. The stroke length––along with bore diameter––determines the engine's displacement. Phases in the power cycle Commonly used engine phases or strokes (i.e. those used in a four-stroke engine) are described below. Other types of engines can have very different phases. Induction-intake stroke The induction stroke is the first phase in a four-stroke (e.g. Otto cycle or Diesel cycle) engine. It involves the downward movement of the piston, creating a partial vacuum that draws a air-fuel mixture (or air alone, in the case of a direct injection engine) into the com ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
BMW E36
The third generation of the BMW 3 Series range of compact executive cars is designated under the model code E36, and was produced by the German automaker BMW from 1990 to 2000. The initial models were of the four-door sedan body style, followed by the coupe, convertible, wagon ("Touring"), hatchback ("Compact"), and the rare four-door convertible Baur TC4 in later years. The E36 was the first 3 Series to be offered in a hatchback body style. It was also the first 3 Series to be available with a six-speed manual transmission (in the 1996 M3), a five-speed automatic transmission, and a four-cylinder diesel engine. The multi-link rear suspension was also a significant upgrade as compared to the previous generations of the 3 Series. Unlike the previous (E30) and successive (E46) generations, all-wheel drive was not available for the E36. The E36 was named in ''Car and Driver'' magazine's 10Best list for every year it was on sale. Following the introduction of its successor, the ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Stroke (engine)
In the context of an internal combustion engine, the term stroke has the following related meanings: * A phase of the engine's cycle (e.g. compression stroke, exhaust stroke), during which the piston travels from top to bottom or vice versa. * The type of power cycle used by a piston engine (e.g. two-stroke engine, four-stroke engine). * "Stroke length", the distance travelled by the piston during each cycle. The stroke length––along with bore diameter––determines the engine's displacement. Phases in the power cycle Commonly used engine phases or strokes (i.e. those used in a four-stroke engine) are described below. Other types of engines can have very different phases. Induction-intake stroke The induction stroke is the first phase in a four-stroke (e.g. Otto cycle or Diesel cycle) engine. It involves the downward movement of the piston, creating a partial vacuum that draws a air-fuel mixture (or air alone, in the case of a direct injection engine) into the com ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Bore (engine)
In a piston engine, the bore (or cylinder bore) is the diameter of each cylinder. Engine displacement is calculated based on bore, stroke length and the number of cylinders: displacement = The stroke ratio, determined by dividing the bore by the stroke, traditionally indicated whether an engine was designed for power at high engine speeds (rpm) or torque at lower engine speeds. The term "bore" can also be applied to the bore of a locomotive cylinder or steam engine pistons. Steam locomotive The term bore also applies to the cylinder of a steam locomotive or steam engine. See also * Bore pitch * Compression ratio * Engine displacement Engine displacement is the measure of the cylinder volume swept by all of the pistons of a piston engine, excluding the combustion chambers. It is commonly used as an expression of an engine's size, and by extension as a loose indicator of the ... References {{Steam engine configurations Engine technology ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
