|
Ariès
The Ariès was a French automobile manufactured by La Société des Automobile Ariès in Asnières-sur-Seine. The firm was founded in 1902 by Baron Charles Petiet. The decision to end production was taken in 1937. Around 20,000 vehicles were produced in total. The first cars were two- and four-cylinder vehicles built 20 chassis at a time in a large factory. These shaft-drive cars had a rather unusual double rear axle, while the engines were built by Aster. In 1907 the company made its own narrow-angle V4 engine. The engine had a single cast iron T-head monobloc on a light alloy crankcase. This contained four cylinders in a square layout with a narrow 15° vee angle. Bore and stroke were 60 by 100mm, giving a capacity of 1.13 litres. It was rated at 8/10 fiscal horsepower. The crankshaft was short with disk webs, two main bearings and fork-and-blade connecting rods. Crankpins and main journals were held in the webs by tapers and a shallow nut, giving the effect of an u ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Ariès 1907
The Ariès was a French automobile manufactured by La Société des Automobile Ariès in Asnières-sur-Seine. The firm was founded in 1902 by Baron Charles Petiet. The decision to end production was taken in 1937. Around 20,000 vehicles were produced in total. The first cars were two- and four-cylinder vehicles built 20 chassis at a time in a large factory. These shaft-drive cars had a rather unusual double rear axle, while the engines were built by Aster. In 1907 the company made its own narrow-angle V4 engine. The engine had a single cast iron T-head monobloc on a light alloy crankcase. This contained four cylinders in a square layout with a narrow 15° vee angle. Bore and stroke were 60 by 100mm, giving a capacity of 1.13 litres. It was rated at 8/10 fiscal horsepower. The crankshaft was short with disk webs, two main bearings and fork-and-blade connecting rods. Crankpins and main journals were held in the webs by tapers and a shallow nut, giving the effect of an u ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Aster (auto Parts Company)
L'Aster, Aster, Ateliers de Construction Mecanique l'Aster, was a French manufacturer of automobiles and the leading supplier of engines to other manufacturers from the late 1890s until circa 1910/12. Although primarily known as an engine mass manufacturer the company also produced chassis for coach-works and a complete range of components. Aster produced a range of engines including: stationary motors; electricity generators; automobile motors; marine engines and aero engines. There were air-cooled and water cooled Gasoline motors, Kerosene motors, and Gas Motors. Among the companies for which Aster produced engines and other parts were Ache Frères, Achilles, Argyll, Ariès, Aster-Newey, Automobiles Barré, Bolide, Belhaven, Bij 't Vuur, Century, Clément, Darracq, Dennis, Durham-Churchill, Ernst, Excelsior, Gladiator, Hanzer, Hoflack, Hurtu, Korn et Latil, Lacoste & Battmann, La Torpille, Lucerna, Newey Aster, Société Parisienne, Passy-Thellier, Pearson, Prune ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Fork-and-blade Connecting Rod
A connecting rod, also called a 'con rod', is the part of a piston engine which connects the piston to the crankshaft. Together with the crank, the connecting rod converts the reciprocating motion of the piston into the rotation of the crankshaft. The connecting rod is required to transmit the compressive and tensile forces from the piston. In its most common form, in an internal combustion engine, it allows pivoting on the piston end and rotation on the shaft end. The predecessor to the connecting rod is a mechanic linkage used by water mills to convert rotating motion of the water wheel into reciprocating motion. The most common usage of connecting rods is in internal combustion engines or on steam engines. __TOC__ Origins The predecessor to the connecting length is the mechanical linkage used by Roman-era watermills. The earliest known example of this linkage has been found at the late 3rd century Hierapolis sawmill in Roman Asia (modern Turkey) and the 6th century s ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Overhead Camshaft
An overhead camshaft (OHC) engine is a piston engine where the camshaft is located in the cylinder head above the combustion chamber. This contrasts with earlier overhead valve engines (OHV), where the camshaft is located below the combustion chamber in the engine block. ''Single overhead camshaft'' (SOHC) engines have one camshaft per bank of cylinders. ''Dual overhead camshaft'' (DOHC, also known as "twin-cam".) engines have two camshafts per bank. The first production car to use a DOHC engine was built in 1910. Use of DOHC engines slowly increased from the 1940s, leading to many automobiles by the early 2000s using DOHC engines. Design In an OHC engine, the camshaft is located at the top of the engine, above the combustion chamber. This contrasts the earlier overhead valve engine (OHV) and flathead engine configurations, where the camshaft is located down in the engine block. The valves in both OHC and OHV engines are located above the combustion chamber; however an OHV ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
CV (tax Horsepower)
The tax horsepower or taxable horsepower was an early system by which taxation rates for automobiles were reckoned in some European countries such as Britain, Belgium, Germany, France and Italy; some US states like Illinois charged license plate purchase and renewal fees for passenger automobiles based on taxable horsepower. The tax horsepower rating was computed not from actual engine power but by a mathematical formula based on cylinder dimensions. At the beginning of the twentieth century, tax power was reasonably close to real power; as the internal combustion engine developed, real power became larger than nominal taxable power by a factor of ten or more. Britain The so-called RAC horsepower rating was devised in 1910 by the RAC at the invitation of the British government. The formula is: : \frac where: : D is the diameter (or bore) of the cylinder in inches, : n is the number of cylinders The formula was calculated from total piston surface area (i.e., "bore" only). The fact ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Aero Engine
An aircraft engine, often referred to as an aero engine, is the power component of an aircraft propulsion system. Most aircraft engines are either piston engines or gas turbines, although a few have been rocket powered and in recent years many small UAVs have used electric motors. Manufacturing industry In commercial aviation the major Western manufacturers of turbofan engines are Pratt & Whitney (a subsidiary of Raytheon Technologies), General Electric, Rolls-Royce, and CFM International (a joint venture of Safran Aircraft Engines and General Electric). Russian manufacturers include the United Engine Corporation, Aviadvigatel and Klimov. Aeroengine Corporation of China was formed in 2016 with the merger of several smaller companies. The largest manufacturer of turboprop engines for general aviation is Pratt & Whitney. General Electric announced in 2015 entrance into the market. Development history * 1848: John Stringfellow made a steam engine for a 10-foot wingspan model ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Hispano-Suiza
Hispano-Suiza () is a Spanish automotive–engineering company. It was founded in 1904 by Marc Birkigt and Damian Mateu as an automobile manufacturer and eventually had several factories in Spain and France that produced luxury cars, aircraft engines, trucks and weapons. In 1923, its French luxury car arm became a semi-autonomous partnership with the Spanish parent company. In 1946, the Spanish parent company sold all of its Spanish automotive assets to Enasa, a Spanish state-owned vehicle manufacturer, and the French arm continued as an independent aviation engine and components manufacturer under the Hispano-Suiza name. In 1968, Hispano-Suiza was taken over by the aerospace company Snecma, which is now part of the French Safran Group. An attempt to relaunch the marque was made by the company Hispano Suiza Cars associated with the Peralada Group (owned by the Suqué Mateu family) in 2019 with a fully-electric car. History Early years In 1898, a Spanish artillery captain, Emilio ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
World War I
World War I (28 July 1914 11 November 1918), often abbreviated as WWI, was one of the deadliest global conflicts in history. Belligerents included much of Europe, the Russian Empire, the United States, and the Ottoman Empire, with fighting occurring throughout Europe, the Middle East, Africa, the Pacific, and parts of Asia. An estimated 9 million soldiers were killed in combat, plus another 23 million wounded, while 5 million civilians died as a result of military action, hunger, and disease. Millions more died in genocides within the Ottoman Empire and in the 1918 influenza pandemic, which was exacerbated by the movement of combatants during the war. Prior to 1914, the European great powers were divided between the Triple Entente (comprising France, Russia, and Britain) and the Triple Alliance (containing Germany, Austria-Hungary, and Italy). Tensions in the Balkans came to a head on 28 June 1914, following the assassination of Archduke Franz Ferdin ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
French Army
The French Army, officially known as the Land Army (french: Armée de Terre, ), is the land-based and largest component of the French Armed Forces. It is responsible to the Government of France, along with the other components of the Armed Forces. The current Chief of Staff of the French Army (CEMAT) is General , a direct subordinate of the Chief of the Defence Staff (CEMA). General Schill is also responsible to the Ministry of the Armed Forces for organization, preparation, use of forces, as well as planning and programming, equipment and Army future acquisitions. For active service, Army units are placed under the authority of the Chief of the Defence Staff (CEMA), who is responsible to the President of France for planning for, and use of forces. All French soldiers are considered professionals, following the suspension of French military conscription, voted in parliament in 1997 and made effective in 2001. , the French Army employed 118,600 personnel (including the Fo ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Commercial Vehicle
A commercial vehicle is any type of motor vehicle used for transporting goods or paying passengers. The United States defines a "commercial motor vehicle" as any self-propelled or towed vehicle used on a public highway in interstate commerce to transport passengers or property when the vehicle: :1. has a gross vehicle weight rating of 4,536 kg (10,001 pounds) or more :2. Is designed or used to transport more than 8 passengers (including the driver) for compensation; :3. Is designed or used to transport more than 15 passengers, including the driver, not used to transport passengers for compensation; :4. Is used in transporting material found by the Secretary of Transportation to be hazardous. The federal definition though followed closely is meant to accommodate and remain flexible to each state's definitions. The European Union defines a "commercial motor vehicle" as any motorized road vehicle, that by its type of construction and equipment is designed for, and capable ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Splash Lubrication
Splash lubrication is a rudimentary form of lubrication found in early engines. Such engines could be external combustion engines (such as stationary steam engines), or internal combustion engines (such as petrol, diesel or paraffin engines). Description An engine that uses splash lubrication requires neither oil pump nor oil filter. Splash lubrication is an antique system whereby scoops on the big-ends of the connecting rods dip into the oil sump and splash the lubricant upwards towards the cylinders, creating an oil mist which settles into droplets. The oil droplets then pass through drillings to the bearings and thereby lubricate the moving parts. Provided that the bearing is a ball bearing or a roller bearing, splash lubrication would usually be sufficient; however, plain bearings typically need a pressure feed to maintain the oil film, loss of which leads to overheating and seizure. The splash lubrication system has simplicity, reliability, and cheapness within its v ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
.jpg "Click for more on -> Ariès 1907")
.jpg "Click for more on -> Commercial Vehicle")
